Page 2041 of 2267
Changing Engine Oil
WARNING:
Be careful not to burn yourself, as the engine oil is hot.
Prolonged and repeated contact with used engine oil
may cause skin cancer; try to avoid direct skin contact
with used oil. If skin contact is made, wash thoroughly
with soap or hand cleaner as soon as possible.
1. Warm up engine, and check for oil leakage from engine com-
ponents.
2. Stop engine.
3. Remove drain plug and oil filler cap.
4. Drain oil and refill with new engine oil.
Oil grade: API SH or SJ/ACEA A2/96
Viscosity: See“RECOMMENDED FLUIDS AND LUB-
RICANTS”, MA-16.
Refill oil capacity (Approximate):
Unit:(Imp pts)
Drain and refill
With oil filter change2.9
Without oil filter change2.7
Dry engine (engine overhaul)3.0
CAUTION:
Be sure to clean drain plug and install with new washer.
Drain plug:
:29-39N·m (3.0 - 4.0 kg-m, 22 - 29 ft-lb)
The refill oil capacity depends on oil temperature and
drain time. Use these specifications as a reference only.
Always use the dipstick to determine when the proper
amount of oil is in the engine.
5. Start engine and check area around drain plug and oil filter
for oil leakage.
6. Run engine for a few minutes, then turn it off. After several
minutes, check oil level.
Changing Engine Oil Filter
1. Remove oil filter with Tool.
WARNING:
Be careful not to burn yourself, as the engine and the engine
oil are hot.
2. Clean the oil filter mounting surface on the cylinder block.
Coat the rubber seal of the new oil filter with engine oil.
SMA672C Oil filler cap
Oil filter
Drain plug
SMA390C Refill oil to this
“H”level.
Do not overfill.
SMA010
ENGINE MAINTENANCEQG
MA-24
Page 2051 of 2267
Changing Air Cleaner Filter
Viscous paper type
Unfasten clamps to change air cleaner filter.
The viscous paper type filter does not need cleaning.
Changing Engine Oil
WARNING:
Be careful not to burn yourself, as the engine oil is hot.
Prolonged and repeated contact with used engine oil
may cause skin cancer; try to avoid direct skin contact
with used oil. If skin contact is made, wash thoroughly
with soap or hand cleaner as soon as possible.
1. Warm up engine, and check for oil leakage from engine com-
ponents.
2. Stop engine.
3. Remove drain plug and oil filler cap.
4. Drain oil and refill with new engine oil.
Oil grade: API SH or SJ/ACEA A2/96
Viscosity: See“RECOMMENDED FLUIDS AND LUBRI-
CANTS”, MA-16.
Refill oil capacity (Approximate):
Unit:(Imp pts)
Drain and refill
With oil filter change3.7 (6 - 1/2)
Without oil filter change3.5 (6 - 1/8)
Dry engine (engine overhaul)3.9 (6 - 7/8)
CAUTION:
Be sure to clean drain plug and install with new washer.
Drain plug:
:29-39N·m (3.0 - 4.0 kg-m, 22 - 29 ft-lb)
The refill oil capacity depends on oil temperature and
drain time. Use these specifications as a reference only.
Always use the dipstick to determine when the proper
amount of oil is in the engine.
5. Start engine and check area around drain plug and oil filter
for oil leakage.
6. Run engine for a few minutes, then turn it off. After several
minutes, check oil level.
NMA006
NMA039 Oil filter
SR20DE engine model
NDI021 Overfill
Normal range
Add
ENGINE MAINTENANCESR20DE
MA-34
Page 2062 of 2267
Changing Engine Oil
WARNING:
Be careful not to burn yourself, as the engine oil is hot.
Prolonged and repeated contact with used engine oil
may cause skin cancer; try to avoid direct skin contact
with used oil. If skin contact is made, wash thoroughly
with soap or hand cleaner as soon as possible.
1. Warm up engine, and check for oil leakage from engine com-
ponents.
2. Stop engine.
3. Remove drain plug and oil filler cap.
4. Drain oil and refill with new engine oil.
Oil specification and viscosity:
ACEA B2-96 (CCMC-PD2)
See“RECOMMENDED FLUIDS AND LUBRICANTS”,
MA-16.
Oil capacity (Approximately):
Unit:(Imp pts)
Drain and refill
With oil filter change5.0
Without oil filter change4.5
Dry engine (engine overhaul)5.1
CAUTION:
Be sure to clean drain plug and install with new washer.
Drain plug:
:29-39N·m (3.0 - 4.0 kg-m, 22 - 29 ft-lb)
The refill capacity depends on the oil temperature and
drain time. Use these specifications for reference only.
Always use the dipstick to determine when the proper
amount of oil is in the engine.
5. Warm up engine, and check area around drain plug and oil
filter for oil leakage.
6. Stop engine.
7. Check oil level.
Changing Engine Oil Filter
1. Remove oil filter with Tool.
WARNING:
Be careful not to burn yourself, as engine and engine oil are
hot.
SMA418C Engine oil drain plug
.SMA411C Oil filter cap
Engine oil
level gauge
SMA822C Refill oil to this“H”
level.
Do not overfill.
SMA412C Engine oil
filter
ENGINE MAINTENANCECD20T
MA-45
Page 2073 of 2267
Engine Maintenance
INSPECTION AND ADJUSTMENT
Drive belt deflection and tension
Deflection adjustment Unit: mm (in) Tension adjustment* Unit: N (kg, lb)
Used belt
New beltUsed belt
New belt
LimitAfter
adjustmentLimitAfter
adjustment
Alternator
Without aircondi-
tioner compressor10.2
(0.402)6.5 - 7.0
(0.256 - 0.276)5.5 - 6.1
(0.217 - 0.240)
292
(29.8, 65.6)652 - 740
(66.5 - 75.5,
146.6 - 166.4)789 - 877
(80.5 - 89.7,
177.4 - 197.6)
With airconditioner
compressor8.1
(0.319)5.3 - 5.7
(0.209 - 0.224)4.5 - 5.0
(0.177 - 0.197)
Power steering
oil pump10.8
(0.425)6.6 - 7.5
(0.260 - 0.295)6.0 - 6.6
(0.236 - 0.260)196
(20.0, 44.1)495 - 583
(50.5 - 59.5,
111.3 - 131.1)603 - 691
(61.5 - 70.5,
135.6 - 155.3)
Applied pushing force 98 N (10 kg, 22 lb)—
*: If belt tension gauge cannot be installed at check points shown, check drive belt tension at a different location on the belt.
Oil capacity (Refill capacity)Unit:(Imp pts)
With oil filter change 2.9 (5 - 1/8)
Without oil filter change 2.7 (4 - 3/4)
Coolant capacityUnit:(Imp pts)
With reservoir tank 6.1 (10 - 3/4)
Reservoir tank 0.8 (1 - 3/8)
Spark plug
Make CHAMPION NGK
Standard typeRC10YCC4
RC10YC4BKR5E-11
Hot typeRC12YCC4
RC12YC4BKR4E-11
Cold typeRC7YCC4
RC7YC4BKR6E-11
Plug gap mm (in) 1.0 - 1.1 (0.039 - 0.043)
SERVICE DATA AND SPECIFICATIONS (SDS)QG
MA-56
Page 2074 of 2267
Engine Maintenance
INSPECTION AND ADJUSTMENT
Drive belt deflection and tension
Deflection adjustment Unit: mm (in) Tension adjustment* Unit: N (kg, lb)
Used belt
New beltUsed belt
New belt
LimitAfter adjust-
mentLimitAfter adjust-
ment
Alternator12-13
(0.47 - 0.51)8-9
(0.31 - 0.35)7-8
(0.28 - 0.31)264
(26.9, 59.3)493 - 583
(50.3 - 59.5,
110.8 - 131.1)11720 70J00 11720 70J05
603 - 691
(61.5 - 70.5,
135.6 - 155.3)652 - 740
(66.5 - 75.5,
146.6 - 166.4)
Air condi-
tioner com-
pressor9 (0.35)5.5 - 6.5
(0.217 -
0.256)4.5 - 5.5
(0.177 -
0.217)304
(31.0, 68.3)534 - 623
(54.5 - 63.5,
120.0 - 140.1)11920 9F500 11920 9F505
652 - 740
(66.5 - 75.5,
146.6 - 166.4)838 - 926
(85.5 - 94.5,
188 - 208)
Power steer-
ing oil pump12
(0.47)8-9
(0.31 - 0.35)7-8
(0.28 - 0.31)264
(26.9, 59.3)493 - 583
(50.3 - 59.5,
110.8 - 131.1)603 - 691
(61.5 - 70.5,
135.6 - 155.3)603 - 691
(61.5 - 70.5,
135.6 - 155.3)
Applied push-
ing force98 N (10 kg, 22 lb)—
*: If belt tension gauge cannot be installed at check points shown, check drive belt tension at a different location on the belt.
Oil capacity (Refill capacity)Unit:(Imp pts)
With oil filter change 3.7 (6 - 1/2)
Without oil filter change 3.5 (6 - 1/8)
Coolant capacity (Refill capacity)
Unit:(Imp pts)
Engine SR20DE
With reservoir tankM/T 6.6 (11 - 5/8)
CVT 6.8 (12)
Reservoir tank 0.8 (1 - 3/8)
Spark plug
Make NGK
Ty p e
Standard BKR6EY-11
Hot—
Cold—
Plug gap mm (in) 1.0 - 1.1 (0.039 - 0.043)
Ignition leadUnit: kΩ/m
Ignition lead Resistance [at 25°C(77°F)]
No. 1 cylinder Approx 3.8
No. 2 cylinder Approx 3.5
No. 3 cylinder Approx 2.7
No. 4 cylinder Approx 2.4
For U.K. (Made by Bougicord) 4.48 - 6.72 kΩ(1.365 - 2.048
kΩ/ft) [at 25°C (77°F)]
SERVICE DATA AND SPECIFICATIONS (SDS)SR20DE
MA-57