1999 MITSUBISHI LANCER EVOLUTION VI Workshop Manual

GENERAL – Tightening Torque00-22
TIGHTENING TORQUE
Each torque value in the table is a standard value
for tightening under the following conditions.
(1) Bolts, nuts and washers are all made of steel
and plated with zinc.
(2) The threads and bearing surface of bolts and
nuts are all in dry condition.The values in the table are not applicable:
(1) If toothed washers are inserted.
(2) If plastic parts are fastened.
(3) If bolts are tightened to plastic or die-cast
inserted nuts.
(4) If self-tapping screws or self-locking nuts are
used.
Standard bolt and nut tightening torque
Thread sizeTorque Nm
Bolt nominal
diameter (mm)Pitch (mm)Head mark “4”Head mark “7”Head mark “8”
M50.82.54.95.9
M61.04.98.89.8
M81.25122225
M101.25244452
M121.25418196
M141.572137157
M161.5111206235
M181.5167304343
M201.5226412481
M221.5304559647
M241.5392735853
Flange bolt and nut tightening torque
Thread sizeTorque Nm
Bolt nominal
diameter (mm)Pitch (mm)Head mark “4”Head mark “7”Head mark “8”
M61.04.99.812
M81.25132428
M101.25264957
M101.5244454
M121.254693103
M121.75428196

11-1
ENGINE
CONTENTS
GENERAL INFORMATION 2. . . . . . . . . . . . . . . .
SPECIFICATIONS 3. . . . . . . . . . . . . . . . . . . . . . . .
Service Specifications 3. . . . . . . . . . . . . . . . . . . . . .
Torque Specifications 5. . . . . . . . . . . . . . . . . . . . . .
New Tightening Method by Use of Bolts
to Be Tightened in Plastic Area 9. . . . . . . . . . . .
Sealants 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Form-In-Place Gasket 10. . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS 11. . . . . . . . . . . . . . . . . . . . . . .
ALTERNATOR AND IGNITION SYSTEM 14.
TIMING BELT 15. . . . . . . . . . . . . . . . . . . . . . . . .
FUEL AND EMISSION CONTROL PARTS 27
SECONDARY AIR SYSTEM AND INTAKE
MANIFOLD 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . EXHAUST MANIFOLD 31. . . . . . . . . . . . . . . . .
WATER PUMP AND WATER HOSE 34. . . . .
ROCKER ARMS AND CAMSHAFT 37. . . . . .
CYLINDER HEAD AND VALVES 43. . . . . . . .
FRONT CASE, COUNTERBALANCE
SHAFT AND OIL PAN 51. . . . . . . . . . . . . . . . .
PISTON AND CONNECTING ROD 59. . . . . .
CRANKSHAFT AND FLYWHEEL 67. . . . . . . .
THROTTLE BODY 73. . . . . . . . . . . . . . . . . . . . .
TURBOCHARGER 75. . . . . . . . . . . . . . . . . . . . .
ALTERNATOR 79. . . . . . . . . . . . . . . . . . . . . . . . .
STARTER MOTOR 83. . . . . . . . . . . . . . . . . . . . .

ENGINE – General Information11-2
GENERAL INFORMATION
DescriptionsSpecifications
TypeIn-line OHV, SOHC
Number of cylinders4
Combustion chamberPentroof + curved top piston type
Total displacement dm31,997
Cylinder bore mm85.0
Piston stroke mm88.0
Compression ratio8.8
Valve timingIntake valveOpens (BTDC)21°
Closes (ABDC)59°
Exhaust valveOpens (BBDC)58°
Closes (ATDC)18°
Lubrication systemPressure feed, full-flow filtration
Oil pump typeInvolute gear type

ENGINE – Specifications11-3
SPECIFICATIONS
SERVICE SPECIFICATIONS
ItemsStandard valueLimit
Timing belt
Auto-tensioner rod projection length mm12–
Auto-tensioner rod pushed-in amount [when pushed with a force of 98
– 196 N] mm1.0 or less–
Rocker arms and camshaft
Camshaft cam height mmIntake35.7935.29
Exhaust35.4934.99
Camshaft journal outer diameter mm26–
Cylinder head and valves
Cylinder head flatness of gasket surface mmLess than 0.050.2
Cylinder head grinding limit of gasket surface mm
Total resurfacing depth of both cylinder head and cylinder block–0.2
Cylinder head overall height mm131.9 – 132.1–
Cylinder head bolt shank length mm–Maximum 99.4
Valve thickness of valve head (margin) mmIntake1.00.5
Exhaust1.51.0
Overall valve length mmIntake109.5109.0
Exhaust109.7109.2
Valve thickness to valve guide clearance
mm
Intake0.02 – 0.050.10
mmExhaust0.05 – 0.090.15
Valve face angle45° – 45.5°–
Valve spring free length mm48.347.3
Valve spring load/installed height N/mm294/40.0–
Valve spring out-of-squareness1.5° or lessMaximum 4°
Valve seat contact width mm0.9 – 1.3–
Valve guide inner diameter mm6.6–
Valve guide projection from cylinder head upper surface mm20.5–
Valve stem projection mmIntake49.2049.70
Exhaust48.4048.90
Oversize rework dimensions of valve guide
hole mm
0.05 O.S.12.05 – 12.07–
hole mm0.25 O.S.12.25 – 11.27–
0.50 O.S.12.50 – 12.52–

ENGINE – Specifications11-4
ItemsLimit Standard value
Intake oversize rework dimensions of valve
guide hole mm
0.3 O.S.35.30 – 35.33–
guide hole mm0.6 O.S.35.60 – 35.63–
Exhaust oversize rework dimensions of
valve guide hole mm
0.3 O.S.33.30 – 33.33–
valve guide hole mm0.6 O.S.33.60 – 33.63–
Front case and oil pan
Oil pump side clearance mmDrive gear0.08 – 0.14–
Driven gear0.06 – 0.12–
Oil pressure at curb idle speed kPa [Oil temperature is 75 to 90°C]78 or more–
Piston and connecting rod
Piston outer diameter mm85.0–
Piston ring side clearance mmNo. 1 ring0.04 – 0.075–
No. 2 ring0.02 – 0.06–
Piston ring end gap mmNo. 1 ring0.25 – 0.350.8
No. 2 ring0.40 – 0.550.8
Oil ring0.10 – 0.401.0
Piston pin outer diameter mm21.0–
Piston pin press-in load N (Room temperature)7,350 – 17,200–
Crankshaft pin oil clearance mm0.02 – 0.050.1
Connecting rod big end side clearance mm0.10 – 0.250.4
Crankshaft and flywheel
Crankshaft end play mm0.05 – 0.250.40
Crankshaft journal outer diameter mm57.0–
Crankshaft pin outer diameter mm44.0–
Crankshaft journal oil clearance mm0.02 – 0.040.1
Bearing cap bolt shank length mm–Maximum 71.1
Piston to cylinder clearance mm0.02 – 0.04–
Cylinder block grinding limit of gasket surface mm
Total resurfacing depth of both cylinder head and cylinder block–0.2
Cylinder block overall height mm284–
Cylinder block inner diameter mm85.0–
Cylinder block cylinder mm0.01–
Turbocharger
Waste gate actuator operation check kPa100113.3

ENGINE – Specifications11-5
ItemsLimit Standard value
Alternator
Rotor coil resistance ΩApprox. 3 – 5–
Protrusion length of brush mm–2
Starter motor
Commutator runout mm0.050.1
Commutator outer diameter mm32.031.4
Commutator undercut mm0.5–
TORQUE SPECIFICATIONS
ItemsNm
Alternator and ignition system
Oil level gauge guide13
Water pump pulley9
Alternator brace (Alternator side)21
Alternator brace (Tightened with water pump)23
Alternator pivot bolt44
Crankshaft pulley25
Center cover3
Spark plug25
Ignition coil10
Timing belt
Timing belt cover (Flange bolt)11
Timing belt cover (Washer bolt)9
Power steering pump bracket49
Tensioner pulley49
Tensioner arm24
Auto tensioner24
Idler pulley48
Crank angle sensor9
Oil pump sprocket54
Camshaft bolt11 8
Tensioner “B”19
Counterbalance shaft sprocket45

ENGINE – Specifications11-6
ItemsNm
Rocker cover3.5
Engine support bracket49
Camshaft sprocket bolt88
Timing belt rear right cover11
Timing belt rear left upper cover11
Fuel and emission control parts
Throttle body18
Fuel pressure regulator9
Delivery pipe11
Vacuum tank bracket9
Solenoid valve bracket9
Solenoid valve9
Vacuum hose and vacuum pipe11
Secondary air intake manifold
Heat protector13
Vacuum hose and vacuum pipe11
Air pipe (Heat protector side)13
Air pipe (Cam position sensor side)11
Air pipe (Eye bolt)49
Air pipe (Control valve side)24
Air control valve21
Air control valve bracket24
Intake manifold stay30
Intake manifold (M8)19
Intake manifold (M10)35
Exhaust manifold
Engine hanger12
Heat protector (Turbocharger side)14
Oxygen sensor54
Exhaust fitting bolt59
Exhaust fitting nut59
Air outlet fitting19

ENGINE – Specifications11-7
ItemsNm
OIl return pipe (Turbocharger side)9
Oil return pipe (Oil pan side – Head mark 7)9
Oil return pipe (Oil pan side – Head mark 10)13
Oil pipe11
Oil pipe eye bolt (Cylinder head side)16
Oil pipe eye bolt (Turbocharger side)30
Water pipe11
Water pipe eye bolt41
Exhaust manifold (M8)29
Exhaust manifold (M10)49
Exhaust manifold (Turbocharger side)59
Water pump and water hose
Water temperature sensor29
Water temperature gauge unit11
Water inlet fitting24
Water outlet fitting (M6)10
Water outlet fitting (M8)13
Thermostat housing24
Thermostat housing (Clamp)11
Water inlet pipe (Cylinder block)13
Water inlet pipe (Outlet fitting)10
Water pump14
Knock sensor22
Rocker arms and camshaft
Camshaft position sensor9
Camshaft position sensor cover10
Camshaft position sensing cylinder21
Camshaft position sensing support13
Camshaft bearing cap20
Oil delivery body11
Cylinder head and valves
Cylinder head bolt [Tighten to 78 Nm and then completely before tightening to final torque
specification]20
90° + 90°