Page 1016 of 3115
D12771
ECM
PWR E829 J/B No.4
E4
(*) Electronically Controlled
Transmission Pattern Select SW
5
W-B
IF IU19
SB Combination Meter
C1519
Cowl Side J/B LH
L-R
1
2
3
(*) Pattern Select Switch (PWR Mode Switch)
When the PWR mode switch is pushed in, the switch contact is made and the PWR mode is selected.
To cancel the PWR mode, push the PWR mode switch once again.C1520
SB312
4F 4C
W-BB
B
E8
E8
E818
28 2nd
PWR
5L-W 10
3M
3PCowl Side J/B RH
18
2E66 24
2E 2QP-B
SNWI MPX1 MPX2
- DIAGNOSTICSAUTOMATIC TRANSMISSION
DI-495
688 Author: Date:
2004 LAND CRUISER (RM1071U)
Pattern Select Switch Circuit (PWR Mode Switch)
CIRCUIT DESCRIPTION
The ECM memory contains the shift programs for the NORMAL and POWER patterns, 2 position, L position
and the lock-up patterns. Following the programs corresponding to the signals from the pattern select
switch, the park/neutral position and other various sensors, the ECM switches the solenoid valves ON and
OFF, and controls the transmission gear change and the lock-up clutch operation.
WIRING DIAGRAM
DI3C5-07
Page 1059 of 3115
DIB31-02
A14471
E9E5E6E7E8 ECM Terminals
- DIAGNOSTICSAUTOMATIC TRANSMISSION
DI-393
586 Author: Date:
2004 LAND CRUISER (RM1071U)
TERMINALS OF ECM
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage (V)
P (E9 6) E1 (E7 1)GW BRIG switch ON and shift lever P position10 to 14P (E9-6) - E1 (E7-1)G-W - BRIG switch ON and shift lever other than P positionBelow 1
N (E9 7) E1 (E7 1)GR BRIG switch ON and shift lever N position10 to 14N (E9-7) - E1 (E7-1)G-R - BRIG switch ON and shift lever other than N positionBelow 1
L4 (E8 4) E1 (E7 1)BL BRIG switch ON and Transfer shift lever L position9 to 14L4 (E8-4) - E1 (E7-1)B-L - BRIG switch ON and Transfer shift lever other than L positionBelow 1.5
SNWI (E8 5) E1 (E7 1)LR BRIG switch ON9 to 14SNWI (E8-5) - E1 (E7-1)L-R - BRIG switch ON and Press continuously 2nd start switchBelow 1
L (E8 8) E1 (E7 1)RL BRIG switch ON and shift lever L position9 to 14L (E8-8) - E1 (E7-1)R-L - BRIG switch ON and shift lever other than L positionBelow 1.5
2 (E8 9) E1 (E7 1)GB BRIG switch ON and shift lever 2 and L position9 to 142 (E8-9) - E1 (E7-1)G-B - BRIG switch ON and shift lever other than 2 and L positionBelow 1.5
D (E8 10) E1 (E7 1)GY BRIG switch ON and shift lever D and 4 position9 to 14D (E8-10) - E1 (E7-1)G-Y - BRIG switch ON and shift lever other than D and 4 positionBelow 1.5
R (E8 11) E1 (E7 1)RB BRIG switch ON and shift lever R position9 to 14R (E8-11) - E1 (E7-1)R-B - BRIG switch ON and shift lever other than R positionBelow 1.5
STP (E8 19) E1 (E7 1)GW BRBrake pedal is depressed7.5 to 14STP (E8-19) - E1 (E7-1)G-W - BRBrake pedal is releasedBelow 1.5
3 (E8 20) E1 (E7 1)GBRIG switch ON and shift lever 3 position9 to 143 (E8-20) - E1 (E7-1)G - BRIG switch ON and shift lever other than 3 positionBelow 1.5
4 (E8 23) E1 (E7 1)GR BRIG switch ON and shift lever 4 position9 to 144 (E8-23) - E1 (E7-1)G-R - BRIG switch ON and shift lever other than 4 positionBelow 1.5
PWR (E8 28) E1 (E7 1)LW BRIG switch ON and Pattern select switch º PWRº OFF9 to 14PWR (E8-28) - E1 (E7-1)L-W - BRIG switch ON and Pattern select switch ºPWRº ONBelow 1
TFN (E7 11) E1 (E7 1)YG BRIG switch ON and Transfer shift lever N positionBelow 1.5TFN (E7-11) - E1 (E7-1)Y-G - BRIG switch ON and Transfer shift lever other than N position9 to 14
SLU+ (E7-16) - SLU- (E7-15)P-G - BEngine idle speedPulse generation 2
reference
IG switch ONBelow 1.5
S2 (E6-10) - E1 (E7-1)W - BR2nd or 3rd gear9 to 14S2 (E6 10) E1 (E7 1)W BR
1st, 4th or 5th gearBelow 1.5
IG switch ON9 to 14
S1 (E6-11) - E1 (E7-1)R - BR1st or 2nd gear9 to 14S1 (E6 11) E1 (E7 1)R BR
3rd, 4th or 5th gearBelow 1.5
Page 1062 of 3115
I25774
C18
Combination Switch
45
CRUISE CANCEL SET/COASTRES/ACC
BRLL L294
55
BR SB BRBR II3Id3
IH2 IX224
E8
1
E7 E1CCS
ECECM DI-998
- DIAGNOSTICSCRUISE CONTROL SYSTEM
1191 Author: Date:
2004 LAND CRUISER (RM1071U)
Main Switch Circuit (Cruise Control Switch)
CIRCUIT DESCRIPTION
This circuit carries the -/SET, +/RESUME and Cancel signals (each voltage) to the ECM.
WIRING DIAGRAM
DIB6C-01
Page 1065 of 3115
DI3CI-14
DI-992
- DIAGNOSTICSCRUISE CONTROL SYSTEM
1185 Author: Date:
2004 LAND CRUISER (RM1071U)
CIRCUIT INSPECTION
DTC P0500/21 Vehicle Speed Sensor ºAº
DTC P0503/23 Vehicle Speed Sensor ºAº Intermittent/Errat-
ic/High
CIRCUIT DESCRIPTION
See page .DI-274
DTC No.DTC Detection ConditionTrouble Area
P0500/21
P0503/23
No vehicle speed sensor signal to ECM under following condi-
tions (a) and (b): (2 trip detection logic)
(a) Park/neutral position switch is OFF
(b) Vehicle is being drivenCombination meter
Open or short in vehicle speed sensor circuit
Vehicle speed sensor
ECM
WIRING DIAGRAM
See page .DI-274
INSPECTION PROCEDURE
See page .DI-274
Page 1067 of 3115
I25773
S5 Stop Light Switch Cowl Side J/B LH Cowl Side J/B RHEngine Control Model
Cowl Side J/B RHCenter J/B
S5 Stop Light Switch
Engine Room J/B
Fusible Link BlockI18 Ignition Switch J4
J/C 21
G-W
G-R
W-R2D35
2D 31
2A10STOP2E 26
2C1
2E41G-WG-W 3M4
3M5
E8 19
STP
ST1- E8 12
R-G 4C9
4E15 4E13
4D9
3 4
B-R R-G 3E4
3E8
B-R B-R A
A
B-R
W-R 7 6
IG2 AM2
1C1
1B9 AM2
B-G
F161
F152J/B No. 2
Battery B-G
IGN
ALT
MAIN DI-994
- DIAGNOSTICSCRUISE CONTROL SYSTEM
1187 Author: Date:
2004 LAND CRUISER (RM1071U)
WIRING DIAGRAM
Page 1084 of 3115
DI3CH-17
I25003
E5E6E7E8E9 DI-990
- DIAGNOSTICSCRUISE CONTROL SYSTEM
1183 Author: Date:
2004 LAND CRUISER (RM1071U)
TERMINALS OF ECM
Symbols (Terminals No.)Wiring ColorConditionSpecified condition
STP e E1GWBRDepress brake pedal10 - 16 VSTP e E1
(E8-19 e E7-1)G-W e BRRelease brake pedalBelow 1 V
Ignition switch ON10 - 16 V
Ignition switch ON
CANCEL switch hold ON3.6 - 7.2 V
Ignition switch ON
-/SET switch hold ON2.1 - 4.9 V
CCS e E1
(E8-24 e E7-1)L e BRIgnition switch ON
+/RES switch hold ON0.7 - 2.6 V
Ignition switch ONBl 1VIgnition switch ON
Main switch OFFBelow 1 V
Ignition switch ON10 14 VIgnition switch ON
Main switch ON10 - 14 V
ST1- e E1RGBRDepress brake pedalBelow 1 VST1 e E1
(E8-12 e E7-1)R-G e BRRelease brake pedal10 - 14 V
Page 1086 of 3115
A19975
ECM
IGSW
+B
MREL
E1 9
E9
E9
E9
E7 4D 4E 3E 3E14 9 8 4
A A
6741 10
536 2E2A
2A 2D1
9
11 1
1
11
1 1
1 8 2 15 3
24
2
44 43
1B 1A5D
5C 1C
1B
1B Cowl Side J/B RH
Engine Room J/B
J/B No. 5 J4
J/C
Cowl Side J/B LH I18
Ignition SW
AM2 IG2
Engine Room R/B
Engine Room J/B
MAIN
BatteryEFI or ECD Relay
EA ECB-R B-R B-R
B-R W-R W-R
B-Y
B-Y
W-R B-G
B-YB-Y
B-W B-W
W-B W-B BR
F15
FL Block
EFI or ECD No. 1
IGN
AM2J/B No. 4 DI-346
- DIAGNOSTICSENGINE
539 Author: Date:
2004 LAND CRUISER (RM1071U)
WIRING DIAGRAM
Page 1090 of 3115
DI-350
- DIAGNOSTICSENGINE
543 Author: Date:
2004 LAND CRUISER (RM1071U)
Fuel Pump Control Circuit
CIRCUIT DESCRIPTION
Refer to DTC P0230 on page DI-162.
WIRING DIAGRAM
Refer to DTC P0230 on page DI-162.
INSPECTION PROCEDURE
Hand-held tester:
1 Check fuel pump operation (See page SF-7).
OK Go to step 8.
NG
2 Connect hand-held tester, and check operation of fuel pump relay.
PREPARATION:
(a) Connect the hand-held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand-held tester main switch ON.
(c) Enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / FUEL PUMP / SPD.
CHECK:
Check the operation of the fuel pump relay when it is switched ON and OFF by the hand-held tester.
OK:
Operating noise can be heard from the relay.
OK Go to step 4.
NG
3 Check operation of fuel pump relay (See page SF-40).
NG Replace fuel pump relay.
OK
DIB2Y-02
