1998 JAGUAR X308 parking brake

5. Remove an d discard the tie
st
rap securing the wheel speed
sensor harness to the brake hose clip.

6. Mark the wi shbone at the
pivot
pin eccentric flan ge marker to
aid installation.

7. Remove the pivot pin nu
t and washer.
8. CAUTION: To prevent damage to the parking brake cable,
the hub carrier must be supported on removal from the wishbone.

Re
move the hub carrie
r from the wishbone.
Re
move the pivot pin from the hub carrier.

Remova
l

2
05-2
34 (JD 550-1)
1. CAUTION: Replacement of nuts and bolts: Various
thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt
can be used. See section 100-00 for information.
Release handbrake.
2. Ra
ise the vehicle on a four-post lift.

3. Fully slacken bu
t do not remove parking brake cable adjuster
nut.

4. Relea s
e appropriate side parkin
g brake cable from connecting
clip.

5. With draw parkin
g brake cable th
rough equalizer (LH side cable
only).
6. Lower four-post lift.
7. Raise rear of vehicle to workin g height and support on stands.
Refer to section 100-02.
8. Remove rear wheel. Refer to section 204-04.

9. P
osition special tool 204-195 on hub studs and install securing
nuts.

10
.
Slacken but do not remove hub to axle shaft securing nut.
11. Remove securing nuts and withdraw special tool (204-195)
from hub.
12. Remove rear brake disc. Refer to 70.10.13.
13. Remove parking brake shoe s. Refer to 70.40.05.

14
.
Remove wheel speed sensor.
Disc
onnect wheel speed sensor harness from sensor
R

emove wheel speed sensor se
curing bolt and withdraw
sensor from hub carrier.

15
.
Sever and discard wheel speed sensor harness tie strap and
position harness for access.
16. Remove hub nut and collar.
Re
move nut.

Remove l
ocating collar.

17 . Install a th
read protector on axle shaft.

18 . R
elease hub from axle shaft.
Pos
i
tion hub puller 204-011 on hub studs.
Inst
al
l securing nuts.
Progres
s
ively tighten
puller center bolt to release hub from
axle shaft splines.
19. Remove hub puller an d thread protector.
Re
move securing nuts and
release puller from hub.
Re
move thread protecto
r from axle shaft.

20 . Relea
se parking brake cable
from suspension mounting
bracket.
Remove cable reta ining clip.

Draw c
a
ble through suspension mounting bracket
aperture.
21. Remove parking brake cable to hub carrier grommet.

22
.
Remove back plate.
Remove two bolts and two scre ws securi
ng back plate to
hub carrier.
With
draw back plate complete
with parking brake cable.

23
.
Mark wishbone at pivot pin eccentric flange marker to aid
installation.

24
.
Remove nut and washer from pivot pin.
25. Remove hub and carrier from wishbone and axle shaft.
With
draw pivot pin and remove
hub and carrier assembly.

1.
Position hub carrier on block of wood.
2. Position ABS-rotor sensor to hub.
Ali g
n assembly to press-ram, and operate press to install
ABS-sensor rotor to hub.

10 . CAUTI
ON: Do not use excessive force when levering
hub.
Measure hub end-float.
Secure hub carri er in vi
ce.
Inst
al
l special tool JD15 to hub.
1. Install dial gauge JD 13A on hub carrier.
2. Using two levers, measure and record hub end-float.
R e
move special tools from hub carrier.

11
. Using h
ydraulic pr
ess, remove hub and outer bearing
assembly from carrier.
1. Position large section of special tool JD132 on press bed, with recess in tool upper most.
2. Position hub carrier on tool, ensuring parking brake cable housing locates in tool recess.
3. Position small section of special tool JD132 on hub.
Alig
n assembly to press-ram, and operate press to remove

hub from hub carrier.

12 . R
emove ABS rotor and inner bearing from hub carrier.
R
e
move ABS rotor.
R
e
move inner bearing.
13. Remove outer bearing assembly from hub.
Remove bearing shim.

25
.
Install hub assembly to wi shbone and axle assembly.
Position hu
b and carrier to wishbone and axle shaft.
Install piv

ot pin ensuring that
eccentric flange correctly
seats in wishbone groove.

26
.
Install washer and nut on pivot pin, but DO NOT tighten nut.

27
.
Install hub on axle shaft .
Route parking brake cable throu
gh hub carrier aperture
and install grommet.
Appl
y Loctite 270 to axle shaft splines and thread, and
fully seat hub on shaft.
28. Install locating collar and hub nut on axle shaft, but DO NOT
tighten hub nut.

35
.
Tighten hub nut to 304-336Nm.
36. Remove securing nuts and withdraw special tool 204-195
from hub.
37. Install rear wheel. Refer to Section 204-04.
38. Remove stands and lower vehi cle onto wheels. Refer to
section 100-02.
39. Raise vehicle on four-post lift.

40
.
Route parking brake cable through suspension mounting
bracket and secure with clip.

41
.
Route parking brake LH ca ble through equalizer.
42. Install LH cable in connecting clip.