1998 JAGUAR X308 lock

            206‐07:  Powe r Brake  Actuation  
                 Specif
ication
 
                 Description  and  Operation  
                     Brake Booster  
                 Removal and  Installation  
                     Brake Booster  (70.50.17)  
                     Brake Booster  and  Brake  Master  Cylinder  (70.50.18)  
 
             206‐09:  Anti ‐Lock  Control  
                 Specification  
                 Description  and  Operation  
                     Anti‐Lock  Control  
                 Diagnosis  and  Testing  
                     Anti‐Lock  Control  
                 Removal and  Installation  
                     Anti‐Lock  Brake  System  (ABS)  Module  (70.60.02)  
                     Front Wheel  Speed  Sensor  (70.60.03)  
                     Hydraulic Cont
rol Unit  (HCU) 
                     Rear Wheel  Speed  Sensor  (70.60.04)  
                     Wheel Speed  Sensor  Ring  (70.60.25)  
 
        211:  Steering  System  
 
             211‐00:  Steering  System ‐ General  Information  
                 Specification  
                 Description  and  Operation  
                     Steering System  
                 Diagnosis  and  Testing  
                     Steering Sy
stem  
                 General Procedures  
                     Power Steering  System Filling  and  Bleeding  
                     Power Steering  System Flushing  (57.15.08)  
                     Power Steering  System Vacuum  Filling  and  Bleeding  
                     Steering Gear  Centralizing  
 
  

                Diagnosi
s
 and  Testing  
                     External Controls  
                 General Procedures  
                     Brake Shift  Interlock  Actuator Adjustment  (44.15.49)  
                     Brake Shift  Interlock  Actuator Manual  Override  
                     Kickdown Switch  Adjustment  (44.15.38)  
                     Selector Lever  Cable  Adjustment  (44.15.07)  
                 Removal and  Installation  
                     Brake Shift  Interlock  Actuator (44.15.48)  
                     Kickdown Switch  (44.15.23)  
                     Selector Lever  Cable  and  Bracket  (44.15.08)  
                     Selector Lev
er Gate  Finish  Panel  (76.25.24)  
                     Selector Lever  Indicator  Assembly  (44.15.14)  
                     Selector Lever  Indicator  Disc  (44.15.15)  
                     Selector Lever  Switch  (44.15.52)  
                     Selector Lever  Knob  (44.15.06)  
                 Disassembly  and  Assembly  
                     Selector Lever  Assembly  (44.15.05)  
 
             307‐05B : Automatic  Transmission/Transaxle  External  Controls  ‐ 4.0L  SC  V8 ‐ AJ26  
                 Description  and  Operation  
                     External Controls  
                 Diagnos
is and  Testing  
                     External Controls  
                 General Procedures  
                     Brake Shift  Interlock  Actuator Manual  Override  
                     Kickdown Switch  Adjustment  (44.15.38)  
                     Selector Lever  Cable  Adjustment  (44.15.07)  
                 Removal and  Installation  
                     Brake Shift  Interlock  Actuator (44.15.48)  
                     Kickdown Switch  (44.15.23)  
                     Selector Lever  Cable  and  Bracket  (44.15.08)  
                     Selector Lever  Gate  Finish  Panel  (76.25.24)  
                     Selector Lev
er Indicator  Disc  (44.15.15)  
                     Transmission  Control Switch  (TCS)  (44.15.12)  
                     Selector Lever  Knob  (44.15.06)  
 

                    Ambient Air Temperature  Sensor  (82.20. 02) 
                     Cold Ai
r
 Bypass  Blend  Door  Actuator  (82.20.86)  
                     Defrost Vent/Register  Blend  Door  Actuator  (82.20.84)  
                     Footwell Vent/Duct  Blend  Door Actuator  (80.20.20  or  82.20.85)  
                     Instrument  Panel  Blend Door  Actuator  (82.20.83)  
                     Remote Climate Control  Module  LHD (82.20.65)  
                     Remote Climate Control  Module  RHD (82.20.65)  
 
        413:  Instrumentation  and Warning  Sy
stems  
 
             413‐00:  Instrument  Cluster  and  Panel  Illumination  
                 Description  and  Operation  
                     Instrument  Cluster  and Panel  Illumination  
                 Removal and  Installation  
                     Instrument  Panel  Dimmer  Switch  (86.65.07)  
 
             413‐01:  Instrument  Cluster  
                 Description  and  Operation  
                     Instrument  Cluster  
                 Diagnosis  and  Testing  
                     Instrument  Cluster  
                 Removal and  Installation  
                     Instrument  Clust
er (88.20.01)  
 
             413‐06:  Horn  
                 Description  and  Operation  
                     Horn 
                 Diagnosis  and  Testing  
                     Horn 
 
             413‐07:  Clock  
                 Description  and  Operation  
                     Clock 
                 Diagnosis  and  Testing  
                     Clock 
                 Removal and  Installation  
                     Clock (88.15.07)  

                    Parcel Shelf  (76.67. 06) 
                     Parcel Shelf
 
Support  (76.67.09)  
                     Passenger Assist  Handle  (76.58.30)  
                     Rear Door  Armrest  (76.34.23)  
                     Rear Door  Trim  Panel  Finish Panel  (76.47.12)  
                     Rear Door  Trim  Panel  (76.34.04)  
                     Rear Window  Blind  (76.14.04)  
                     Rear Door  Window  Control  Switch  Finish  Panel  (76.47.34)  
                     Scuff Plate Trim  Panel  (76.13.81)  
                     Sun Visor  (76.10.48)  
 
             501‐08:  Exterior  Trim  and  Or
namentation  
                 Description  and  Operation  
                     Exterior Trim  
                 Removal and  Installation  
                     A‐Pillar  Moulding  LH  (76.13.19)  
                     A‐Pillar  Moulding  RH  (76.13.20)  
                     Coachlines 
                     Door Moulding  (76.43.72)  
                     Front Fender  Moulding  (76.10.48)  (76.43.73)  
                     Luggage Compartment  Lid Badges  (76.44.03)  
                     Luggage Compartment  Lid Moulding  (76.43.79)  
                     Radiator Grille (76.
55.03)  
                     Radiator Grille Bezel  (76.55.15)  
 
             501‐09:  Rear  View  Mirrors 
                 Description  and  Operation  
                     Rear View  Mirrors  
                 Removal and  Installation  
                     Auto‐Dimming  Interior  Mirror  (76.10.56)  
                     Exterior Mirror  (76.10.52)  
                     Exterior Mirror  Cover  (76.10.55)  
                     Exterior Mirror  Glass  (76.10.53)  
                     Exterior Mirror  Motor  (76.10.57)  (76.11.09)  
                     Interior Mirror  (76.10.51)  
                     Interior Mirro
r Mounting  Block  (76.10.62)  
 

                    Rear Cup  Holder  (76.25.27)  
                     Steering Col u
mn 
Lower  Shroud  (76.46.03)  
                     Steering Column  Upper Shroud  (76.46.02)  
 
             501‐14:  Handles,  Locks,  Latches  and  Entry  Systems  
                 Description  and  Operation  
                     Handles, Locks,  Latches  and  Entry  Systems  
                 Removal and  Installation  
                     Exterior Driver  Door  Handle  (76.58.07)  
                     Driver Door  Latch (76.37.74)  
                     Glove Compartment Lid  Ha
ndle  (76.52.08)  
                     Glove Compartment  Lid Lock  Cylinder  (76.52.23)  
                     Luggage Compartment  Lid Latch  (76.19.25)  
                     Luggage Compartment  Lid Latch  Actuator  (76.19.25)  
                     Luggage Compartment  Lid Release  Switch  (86.25.56)  
                     Luggage Compartment  Lid Warning  Indicator  Switch (86.65.93)  
                     Exterior Passenger  Door  Handle  (76.58.08)  
                     Passenger Door  Latch  (76.37.75)  
                     Exterior Rear  Door  Handle  (76.58.02)  
                     Rear Door  Latch  (76.37.09)  
 
             501‐16:  Wipers  and  Washers  
                 Descriptio
n and  Operation  
                     Wipers and Washers  
                 Removal and  Installation  
                     Headlamp Washer Jet  (84.20.08)  
                     Headlamp Washer Pump  (84.20.21)  
                     Rain Sensor  (84.12.10)  (86.56.62)  
                     Windshield  Washer  Pump  (84.10.21)  
                     Windshield  Washer  Reservoir  (84.10.01)  (84.10.03)  
                     Windshield  Wiper  Motor  (84.15.13)  
                     Windshield  Wiper/
Washer  Switch  (86.65.42)  
                     Wiper Pivot  Arm  (84.15.03)  
 
  

Gener
al specifications (including setting-up information, capacities, lubricants, fluids, sealants and adhesives).
To
r
que specifications.
Description and Operation
A g
eneral illustration and part
s list to identify the components which comp rise a particular system or assembly.
A b
rief description of the system operating characteristics or description of the assembly.
A d

escription of each component and its function.
Diagnosis and Testing
D e
scriptions of how to iden
tify system problems.
Inspection and verifi
cation information.
S
y
mptom charts comprising fault conditions, possible sources and actions.
General Procedures
G e
neral maintenance procedures, including adjustment, alig
nment, bleeding and filling, with illustrated steps and
supporting text.
Tigh te
ning torque specifications, shown in the illustrations.
Removal and Installation
Com p
onent removal and installation maintenance proced
ures, with illustrated steps and supporting text.
Tighte
ning torque specifications, shown in the illustrations.
An i
llustrated tool
chart for each proced
ure requiring the use of special tools.
Disassembly and Assembly
Compon ent disassembly and
assembly
maintenance procedures, with illust rated steps and supporting text.
Tighte
ning torque specifications, shown in the illustrations.
An i
llustrated tool
chart for each proced
ure requiring the use of special tools.
Repairs and Replacem
ents
Wh
en s
ervice parts are required, it is essential that only genuine Jaguar/Daimler replacements are used.
Attention is drawn to the following points concerning repa irs and the fitting of replacement parts and accessories:
Safety feat
ures embodied in the vehicle
may be impaired if other than genuine parts are fitted. In certain territories,
legislation prohibits the fitting of pa rts which are not produced to the vehi cle manufacturer's specification.
Torque wrench setting figures given i
n this manual must be strictly adhered to. Locking devices, where specified,
must be fitted. If the efficiency of a locking device is impaired during removal it must be renewed.
O w
ners purchasing accessories
while travelling abroad should ensure that the accessory and its fitted location on the
vehicle conform to mandatory requirements existing in their country of origin.
The vehicle warranty may be invali
dated by the fitting
of other than genuine Ja guar/Daimler parts. All
Jaguar/Daimler replacements have the fu ll backing of the factory warranty.
Jaguar/Daimler dealers are obliged to

supply only genuine service parts.
Thread Locking Devices
P a
tched Fasteners
Two types
of
patched fastener are essentially used on certai
n suspension, steering and other critical components, where
operational movement of the component necessitates positive thread locking. Standard patched fasteners have part
numbers bearing the suffix le tter M. For identification of special patched fa steners, refer to the list of patched fasteners
below, or the relevant component drawings.
Jaguar Specification JFS 02.01.02 patched fasteners incorporate a micro-encapsulated adhesive which is released into the
mating threads during tightening. Following final tightening, the adhesive in this type of patched fastener must be allowed a
period to cure before the component/vehicle is used. On removal, this type of fastener must be discarded and a new

Torque Specifications
Torque sp
ecifications are shown in maintenance procedure illustra
tions and also in the torque specifications chart located at
the front of the relevant section.
Disconnecting/Connecting the Battery
Ow ing t
o the electronic components used on the vehicle, it is important that the battery is disconnected when specified in a
maintenance procedure.
When the battery is connected, the specified procedure must be followed, to ensure the correct operation of all vehicle
systems; refer to Section 414-01.
Use of Control Modules
Control modu les may
only be used on the ve
hicle to which they were originally fitted. Do not attempt to use or test a control
module on any other vehicle.
Function
al Test
On
completion of a maintenance procedure, a thorough test should be carried out, to ensu
re that the relevant vehicle
systems are working correctly.
Protecting the Vehicle
Al ways
fit covers to protect
the fenders before commencing work in the engi ne compartment. Cover the seats and carpets,
wear clean overalls and wash hands or wear gloves before working inside the vehicle. Avoid spilling hydraulic fluid,
antifreeze or battery acid on the paintwork. In the event of spillage, wash off with water imme diately. Use polythene sheets
in the trunk to protect carpets. Always use the recommended service tool, or a satisfactory equivalent, where specified.
Protect temporarily exposed screw thread s by replacing nuts or fitting caps.
Preparation
Before disassembly, clean the surrounding ar ea
as thoroughly as possible. When co
mponents have been removed, blank off
any exposed openings using grease-proof paper and masking tape. Immediately seal fuel, oil and hydraulic lines when
separated, using plastic caps or plugs, to prevent loss of fluid and the entry of dirt. Close the open ends of oilways, exposed
by component removal, with tapered hardw ood plugs or readily visible plastic plugs. Immediately a component is removed,
place it in a suitable container; use a se parate container for each component and its associated pa rts. Before dismantling a
component, clean it thoroughly with a recommended cleaning agent; check that the agent will not damage any of the
materials within the component. Clean the bench and obtain ma rking materials, labels, containers and locking wire before
dismantling a component.
Dismantling
O b
serve scrupulous cleanliness when dismantling components,
particularly when parts of the brake, fuel or hydraulic
systems are being worked on. A particle of dirt or a fragment of cloth could caus e a dangerous malfunction if trapped in
these systems. Clean all tapped holes, crev ices, oilways and fluid passages with compressed air. Do not permit compressed
air to enter an open wound. Always use ey e protection when using compressed air.
Ensure that any O-rings used for sealing are correctly refitted or renewed if disturbed. Mark mating parts to ensure that
they are replaced as dismantled. Whenever possible use markin g materials which avoid the possibilities of causing distortion
or the initiation of cracks, which could occur if a center pu nch or scriber were used. Wire together mating parts where
necessary to prevent accidental interchange (e.g roller bearing components). Tie labels on to all parts to be renewed and to
parts requiring further inspection before being passed fo r reassembly. Place labelled parts and other parts for rebuild in
separate containers. Do not disc ard a part which is due for renewal until it ha s been compared with the new part, to ensure
that the correct part has been obtained.

Before inspecting a component for wear or per
forming a dimensional check,
ensure that it is absolutely clean; a slight smear
of grease can conceal an incipient failure. When a component is to be checked dimensionally against figures quoted for it,
use the correct equipment (surface plates, micrometers, dial gauges etc.) in serviceable condition. The use of makeshift
equipment can be dangerous. Reject a component if its dimensio ns are outside the limits quoted, or if damage is apparent.
A part may be refitted if its critical di mension is exactly to the limit size and it is otherwise satisfactory. Use Plastigauge 12
Type PG-1 for checking bearing surface clearance, e.g. big end bearing shell to crank jour nal. Instructions for the use of
Plastigauge and a scale giving bearing clearances in steps of 0.0025 mm (0.0001 in) are supplied with the package.
Safety
Precautions
• WAR
NINGS:
WORKING ON THE FUEL SYSTEM RESULTS IN FUEL AND FUEL VAPOUR BEING PRESENT IN THE ATMOSPHERE. FUEL
VAPOUR IS EXTREMELY FLAMMABLE, HENCE GREAT CARE MUST BE TAKEN WHILST WORKING ON THE FUEL SYSTEM.
ADHERE STRICTLY TO THE FOLLOWING PRECAUTIONS:
DO
NOT SMOKE IN THE WORK AREA.
DISP

LAY 'NO SMOKING' SIGNS AROUND THE AREA.
DISCONNECT TH

E BATTERY BEFORE WORKING ON THE FUEL SYSTEM.
DO NOT CONNEC

T/DISCONNECT ELECTRICAL CIRCUITS
, USE ELECTRICAL EQUIPMENT OR OTHER TOOLS OR
ENGAGE IN WORKING PRACTICES WHICH IN ANY WAY MAY RESULT IN THE PRODUCTION OF SPARKS.
ENS
URE THAT A CO2 FIRE EXTINGUISHER IS CLOSE AT HAND.
ENS

URE THAT DRY SAND IS AVAILABLE TO SOAK UP ANY FUEL SPILLAGE.
EMP

TY FUEL USING SUITABLE FIRE PROOF EQUIPMENT IN
TO AN AUTHORIZED EXPLOSION PROOF CONTAINER.
DO NOT EMP
TY FUEL WHILE WORKING IN A WORKSHOP OR A PIT.
ENS

URE THAT WORKING AREA IS WELL VENTILATED.
ENS

URE THAT ANY WORK ON THE FUEL SYSTEM IS ON
LY CARRIED OUT BY EXPERIENCED AND WELL QUALIFIED
MAINTENANCE PERSONNEL.
ENS
URE THAT FUME EXTRACTION EQUIPMENT IS USED WHERE APPROPRIATE.
FUME EXTRACTION EQUIPMENT MUST BE IN OPERATION WHEN SOLVENTS ARE USED E.G. TRICHLOROETHANE,
WHITE SPIRIT, SBP3, METHYLENE CHLORIDE, PERCHLORETHY LENE. DO NOT SMOKE IN THE VICINITY OF VOLATILE
DEGREASING AGENTS.
General workshop practices:
Disc
onnect the grounded termin
al of the vehicle battery.
D
o not apply heat in an attempt to free seized nuts or fitt
ings; as well as causing damage to protective coatings,
there is a risk of damage from stray heat to electronic equipment and brake lines.
Keep oils and solven
ts away from naked flames and other sour
ces of ignition.
Adhere str
ictly to handling and safety inst
ructions given on containers and labels.
E
nsure that a suitab
le form of fire extinguisher is conveniently located.
Wh
en using electrical tools and equipment, inspect the power
lead for damage and check that it is properly earthed.
D
o not leave tools, equipment, spilt oil etc. around the work area.
Working beneath a vehicle:
Wh
enever possible, use a ramp or
pit in preference to jacking.
Posit
ion chocks at the wheels as we
ll as applying the parking brake.
N
ever rely on a jack alone to support a
vehicle; use axle stands, or blocks care fully placed at the jacking points, to
provide a rigid location.
Ch
eck that any lifting equipment used has adeq
uate capacity and is fully serviceable.
Working on air conditioning systems:
D
o not disconnect any pipes of the refrigeration system
unless you are trained and instructed to do so; a refrigerant
is used which can cause blindness if allowed to come into contact with the eyes.
Health Protection

P

rolonged and repeated contact with mineral oil will result in the removal of natural oils from the skin, leading to dryness,


In
spection