1997 TOYOTA SUPRA parking brake

Q04160
Push Rod Play and
Freeplay Adjust Point
Pedal
HeightPedal Height
Adjust Point
Push Rod PlayCL03Z-01
CL0102Pedal Freeplay
Z13785
25 mm (0.98 in.) or more
Full Pedal Stroke Full Stroke
End PositionRelease
Point
- CLUTCHCLUTCH PEDAL
CL-3
1544 Author
: Date
:
1997 SUPRA (RM502U)
CLUTCH PEDAL
INSPECTION
1. CHECK PEDAL HEIGHT
Pedal height from asphalt sheet:
146.2 - 156.2 mm (5.76 - 6.15 in.)
2. IF NECESSARY, ADJUST PEDAL HEIGHT
Loosen the lock nut and clutch switch until the height is correct.
Tighten the lock nut.
HINT:
Before rotating the clutch switch for pedal height adjustment,
disconnect the clutch switch connector.
3. CHECK PEDAL FREEPLAY AND PUSH ROD PLAY
Push in on the pedal until the beginning of clutch resistance is
felt.
Pedal freeplay: 5.0 - 15.0 mm (0.197 - 0.591 in.)
Gently push on the pedal until the resistance begins to increase
a little.
Push rod play at pedal top:
1.0 - 5.0 mm (0.039 - 0.197 in.)
4. IF NECESSARY, ADJUST PEDAL FREEPLAY AND
PUSH ROD PLAY
(a) Loosen the lock nut and turn the push rod until the free-
play and push rod play are correct.
(b) Tighten the lock nut.
(c) After adjusting the pedal freeplay, check the pedal height.
5. INSPECT FULL PEDAL STROKE
Full pedal stroke: 132.0 - 138.0 mm (5.20 - 5.43 in.)
6. INSPECT CLUTCH RELEASE POINT
(a) Pull the parking brake lever and install wheel stopper.
(b) Start the engine and idle the engine.
(c) Without depressing the clutch pedal, slowly shift the shift
lever into the reverse position until the gears contact.
(d) Gradually depress the clutch pedal and measure the
stroke distance from the point the gear noise stops (re-
lease point) up to the full stroke end position.

38SUPRAÐNEW FEATURES
2. Sound Absorbing Materials
Seal material has been newly provided to the bottom of the front pillar, and a quarter service hole cover has been
newly provided to the quarter portion in order to reduce road noise while driving.
The material of sound absorbing material used in the roof side inner garnish, quarter trim, deck side trim and deck
rear trim has been changed to reduce road noise.

CRUISE CONTROL SYSTEM
1. Actuator
The '97 Supra has adopted a new motor type actuator that is both lightweight and simple in construction.
The basic construction and operation of this actuator are the same as in the '96 4Runner with 5VZ±FE engine.
For details, see the 1996 4Runner New Car Features (Pub. No. NCF126U), page 71.
2. Cruise Control ECU
Manual Cancel Function
The manual cancel function, which cancels the cruise control when the parking brake is operated, has been
discontinued.

38SUPRAÐNEW FEATURES
3. Sound Absorbing Materials
Seal material has been newly provided to the bottom of the front pillar, and a quarter service hole cover has been
newly provided to the quarter portion in order to reduce road noise while driving.
The material of sound absorbing material used in the roof side inner garnish, quarter trim, deck side trim and deck
rear trim has been changed to reduce road noise.

CRUISE CONTROL SYSTEM
1. Actuator
The '97 Supra has adopted a new motor type actuator that is both lightweight and simple in construction.
The basic construction and operation of this actuator are the same as in the '96 4Runner with 5VZ±FE engine.
For details, see the 1996 4Runner New Car Features (Pub. No. NCF126U), page 71.
2. Cruise Control ECU
Manual Cancel Function
The manual cancel function, which cancels the cruise control when the parking brake is operated, has been
discontinued.

124APPENDIXÐSUPRA

SUPRA
Item AreaU.S.A..Body Type2±Door Liftback (Standard Roof)2±Door Liftback (Sport Roof)Vehicle GradeÐModel CodeJZA80L±ALMVFAJZA80L±ALPVFAJZA80L±AJMVFAJZA80L±AJPVFALength mm (in.)4515 (177.8)uuu
OverallWidth mm (in.)1810 (71.3)uuuOverallHeight* mm (in.)1275 (50.2)uuuWheel Base mm (in.)2550 (100.4)uuu
TreadFront mm (in.)1520 (59.8)uuuTreadRear mm (in.)1525 (60.0)uuu
Effective Head RoomFront mm (in.)953.2 (37.5)u946.8 (37.3)uEffective Head RoomRear mm (in.)834.5 (32.9)uuu
sEffective Leg RoomFront mm (in.)1117.0 (44.0)uuu
ghtsEffective Leg RoomRear mm (in.)605.1 (23.8)uuu
We i g
h
Shoulder RoomFront mm (in.)1376.3 (54.2)uuu
icle WShoulder RoomRear mm (in.)1113.2 (43.8)uuu
VehicOverhangFront mm (in.)950 (37.4)uuu
s & VeOverhangRear mm (in.)1015 (40.0)uuu
sions
&Min. Running Ground Clearance mm (in.)120 (4.7)uuu
mensioAngle of Approach degrees13uuu
DimeAngle of Departure degrees17uuu
ajor DFront kg (lb)762 (1680)778 (1715)773 (1705)789 (1740)MajoCurb WeightRear kg (lb)694 (1530)703 (1550)710 (1565)719 (1585)MCurb WeightTotal kg (lb)1456 (3210)1481 (3265)1483 (3270)1508 (3325)Front kg (lb)937 (2065)uuuGross Vehicle WeightRear kg (lb)1002 (2210)uuuGross Vehicle WeightTotal kg (lb)1939 (4275)uuuFuel Tank Capacity l (U.S. gal., Imp. gal.)70 (18.5, 15.4)uuuLuggage Compartment Capacity m3 (cu. ft.)ÐÐÐÐMax. Speed km/h (mph)240 (150)uuuMax. Cruising Speed km/h (mph)193 (120)uuu
Acceleration0 to 100 km/h sec.6.87.46.87.4
ceAcceleration0 to 400 m sec.15.215.715.215.7
mance1st Gear km/h (mph)54 (34)61 (38)54 (34)61 (38)
rform
a
Max Permissible Speed2nd Gear km/h (mph)94 (58)112 (70)94 (58)112 (70)PerfoMax. Permissible Speed3rd Gear km/h (mph)139 (86)Ð139 (86)ÐP4the Gear km/h (mph)ÐÐÐÐTurning DiameterWall to Wall m (ft.)11.5 (38)uuuTurning Diameter(Outside Front)Curb to Curb m (ft.)10.9 (36)uuuEngine Type2JZ±GEuuuValve Mechanism24±Valve, DOHCuuuBore x Stroke mm (in.)86.0 x 86.0 (3.39 x 3.39)uuu
eDisplacement cm3 (cu. in..)2997 (182.9)uuu
ngineCompression Ratio10.0 : 1uuuEngCarburetor TypeSFIuuuResearch Octane No. RON96uuuMax. Output (SAE±NET) kW/rpm (HP @ rpm)164/5800 (220 @ 5800)uuuMax. Torque (SAE±NET) N.m/rpm (lb±ft @ rpm)285/4800 (210 @ 4800)uuu
alBattery Capacity (20HR) Voltage & Amp. hr.12±52uuu
ginectric a lGenerator Output Watts1080uuuEnginElectrStarter Output kW1.4uuuClutch TypeDry, Single PlateÐDry, Single PlateÐTransmission TypeW58A340EW58A340EIn First3.2852.8043.2852.804In Second1.8941.5311.8941.531In Third1.2751.0001.2751.000Transmission Gear RatioIn Fourth1.0000.7051.0000.705Transmission Gear RatioIn Fifth0.783Ð0.783ÐIn SixthÐÐÐÐIn Reverse3.7682.3933.7682.393Differential Gear Ratio4.083uuuDifferential Gear Size mm (in.)205 (8.07)uuu
ssisBrake TypeFrontVentilated Discuuu
ChassBrake TypeRearVentilated DiscuuuChParking Brake TypeDual±ServouuuBrake Booster Type and Style in.Tandem 8º + 9ºuuuProportioning Valve TypeP & B Valveuuu
Suspension TypeFrontDouble WishboneuuuSuspension TypeRearDouble Wishboneuuu
Stabilizer BarFrontSTDuuuStabilizer BarRearSTDuuuSteering Gear TypeRack & PinionuuuSteering Gear Ratio (Overall)17.5 : 1uuuPower Steering TypeIntegral Typeuuu* : Unladen Vehicle, *1 : Electrically Controlled Transmission with an intelligent sporty control

BE-4
- BODY ELECTRICALBODY ELECTRICAL SYSTEM
1982 Author
: Date
:
1997 SUPRA (RM502U) Taillight does not light with light control SW in TAIL.
1. Taillight Relay (J/B No.1)
2. Integration Relay
3. Light Control Switch
4. Wire HarnessBE-17
BE-13
BE-17
Taillight does not go out with light control SW in OFF.
1. Taillight Relay (J/B No.1)
2. Integration Relay
3. Light Control switch
4. Wire HarnessBE-17
BE-13
BE-17
Headlight and Taillight do not light with engine running and light
control SW in OFF.
1. GAUGE Fuse (J/B No.1)
2. Generator L Terminal
3. D.R.L. Relay
4. D.R.L. No.2 Relay (R/B No.2)
5. D.R.L. No.3 Relay
6. Parking Brake Switch
7. Wire Harness
BE-17
BE-17
BE-17
BE-43
FOG LIGHT SYSTEM
SymptomSuspect AreaSee page
Fog light does not light with light control SW HEAD.
(Headlight is normal.)
1. FOG Fuse (R/B No.2)
2. HEAD Fuse (R/B No.2)
3. Fog Light Relay (R/B No.2)
4. Fog Light Switch
5. Wire Harness
BE-23
BE-23
Fog light does not light with light control SW HEAD.
(Headlight does not light)1. Headlight and Taillight system
2. Wire HarnessBE-15
Only one light does not light.1. Bulb
2. Wire Harness
TURN SIGNAL HAZARD WARNING SYSTEM
SymptomSuspect AreaSee page
ºHazardº and ºTurnº do not light up.
1. Hazard Warning Switch
2. Turn Signal Flasher
3. Wire HarnessBE-26
BE-26
The flashing frequency is abnormal.
1. Bulb
2. Turn Signal Flasher
3. Wire Harness
BE-26
Hazard warning light does not light up.
(Turn is normal.)1. HAZ-HORN Fuse (R/B No.2)
2. Wire Harness
Hazard warning light does not light up in one direction.1. Hazard Warning Switch
2. Wire HarnessBE-26
Turn signal does not light up.
(Combination meter, wiper and washer do not operate.)
1. TURN Fuse (J/B No.1)
2. Ignition Switch
3. Turn Signal Switch
4. Wire Harness
BE-13
BE-26
Turn signal does not light up.
1. TURN Fuse (J/B No.1)
2. Turn Signal Switch
3. Wire Harness
BE-26
Turn signal does not light up in one direction.1. Turn Signal Switch
2. Wire HarnessBE-26
Only one bulb does not light up.1. Bulb
2. Wire Harness

- BODY ELECTRICALBODY ELECTRICAL SYSTEM
BE-7
1985 Author
: Date
:
1997 SUPRA (RM502U)
WARNING LIGHTS:
SymptomSuspect AreaSee page
Warning lights do not light up.
(Except Discharge and Door Open)
1. Bulb
2. IGN Fuse (J/B No.1)
3. Ignition Switch
4. Meter Circuit
5. Generator
6. Wire Harness
BE-13
BE-40
Brake Warning Light does not light up.
1. Bulb
2. Brake Fluid Level Warning Switch
3. Parking Brake Switch
4. Bulb Check Relay
5. Meter Circuit
6. Wire Harness
BE-43
BE-43
BE-40
Seat Belt Warning Light does not light up.
1. Bulb
2. Seat Belt Buckle Switch
3. Integration Relay
4. Meter Circuit
5. Wire Harness
BE-43
BE-13
BE-40
Engine Oil Level Warning Light does not light up.
1. Bulb
2. Engine Oil Level Warning Switch
3. Meter Circuit
4. Wire Harness
BE-43
BE-40
Low Oil Pressure Warning Light does not light up.
1. Bulb
2. Low Oil Pressure Warning Switch
3. Meter Circuit
BE-43
BE-40
Door Open Warning Light does not light up.
1. Bulb
2. DOME Fuse (R/B No.2)
3. Door Courtesy Switch
4. Luggage Room Light Switch
5. Integration Relay
6. Meter Circuit
7. Wire Harness
BE-28
BE-28
BE-13
BE-40
Master Warning Light does not light up.
1. Bulb
2. Telltale Light Circuit
3. Meter Circuit
4. Wire Harness
BE-40
BE-40
INDICATOR LIGHTS:
SymptomSuspect AreaSee page
SRS Indicator Light does not light up.
1. Bulb
2. Center Airbag Sensor
3. Wire Harness
DI-555
ABS Indicator Light does not light up.
1. Bulb
2. Traction ECU
3. Wire Harness
DI-499
Malfunction Indicator Light does not light up.
1. Bulb
2. ECM
3. Wire Harness
DI-1
DI-145
TRAC OFF Indicator Light does not light up.
1. Bulb
2. Traction Solenoid Relay
3. Traction ECU
4. Wire Harness
DI-499
DI-499

Z07503
Wire Harness Side
Z09181
34
2 143
12 BE-18
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
1996 Author
: Date
:
1997 SUPRA (RM502U)
6. INSPECT DOOR COURTESY SWITCH CONTINUITY
(See page BE-28)
7. CANADA models only:
INSPECT D.R.L. MAIN RELAY CIRCUIT
Disconnect the connector from relay and inspect the connector
on wire harness side, as shown.
Tester connectionConditionSpecified condition
5 - GroundHeadlight dimmer switch position Low beam or
high beamNo continuity
5 - GroundHeadlight dimmer switch position FlashContinuity
8 - GroundParking brake switch position OFFNo continuity
8 - GroundParking brake switch position ONContinuity
16 - GroundHeadlight dimmer switch position Low beamNo continuity
16 - GroundHeadlight dimmer switch position Flash or High
beamContinuity
13 - GroundConstantContinuity
18 - GroundConstantContinuity
2 - GroundIgnition switch position LOCK or ACCNo voltage
2 - GroundIgnition switch position ONBattery positive voltage
11 - GroundEngine StopNo voltage
11 - GroundEngine RunningBattery positive voltage
15 - Ground
17 - GroundConstantBattery positive voltage
If the circuit is as specified, try replacing the relay with a new
one.
If the circuit is not as specified, inspect the circuit connected to
other parts.
8. INSPECT D.R.L. NO.2 RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant3 - 4Continuity
Apply B+ between
terminals 3 and 4.1 - 2Continuity
If continuity is not as specified, replace the relay.

Z14743
Connector B
Connector AB1
B3
B2B4
A1 A5A3 A2
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
BE-19
1997 Author
: Date
:
1997 SUPRA (RM502U)
9. INSPECT D.R.L. NO.3 RELAY CONTINUITY
Tester connectionConditionSpecified condition
A1 - B3ConstantContinuity
A3 - A5ConstantContinuity
B3 - B4ConstantContinuity
A2 - A5Apply battery positive voltage
between terminal A1 and B3.Continuity
B1 - B2Apply battery positive voltage
between terminal B3 and B4.Continuity
If continuity is not as specified, replace the relay.
10. INSPECT PARKING BRAKE SWITCH CONTINUITY
(See page BE-43)