1997 TOYOTA SUPRA window

28 Noise NOISE PRODUCED BY VIBRATION OR SHOCK WHILE DRIVING
No
Ye s Is speaker properly installed?
Noise is produced from static electricity accumulating in the vehicle body. With vehicles stationary lightly tap each system.
Is noise produced?Install properly.
Each system faulty. Is speaker properly installed?
No
No Ye s
Ye s
29 Noise NOISE PRODUCED WHEN ENGINE STARTS
NoYe s Whistling noise which becomes high-pitched when
accelerator strongly depressed, disappears shortly
after engine stops.Generator noise.
A/C noise.
Fuel gauge noise.
Horn noise.
Ignition noise.
Turn signal noise.
Washer noise.
Engine coolant temp. gauge noise.
Wiper noise. Whining noise occurs when A/C is operating.
Scratching noise occurs during sudden acceleration, driving on rough
roads or when ignition switch is turned ON.
Clicking sound is heard when horn button is pressed, then
released. Whirring/grating sound is heard when pushed
continuously.
Murmuring sound stops when engine stops.
Tick-tack noise occurs in co-ordination with blinking
offlasher.
Noise occurs during window washer operation.
Scratching noise occurs while engine is running,
and continues a while even after engine stops.
Scraping noise in line with wiper beat.
Other type of noiseYe s
Ye s
Ye s
Ye s
Ye s
Ye s
Ye s
Ye s No
No
No
No
No
No
No
No
- BODY ELECTRICALAUDIO SYSTEM
BE-95
2073 Author
: Date
:
1997 SUPRA (RM502U)

BO0QC-01
N19534
Outside Handle
Door Lock CylinderDoor Glass
Belt Moulding
Outer Rear View Mirror
Door Hinge
Door Check Door Window Upper Stop
Door Lock
Door Hinge
Weatherstrip
Glass Guide
Service Hole Cover Inside Panel
Frame
Window Regulator
Armrest Bracket
Setting Nut
Window Guide
Lower PlateInside Handle
Plate
Trim BoardInside Handle
Speaker
Power Window Switch
(Passenger's) Inside Handle Bezel
Power Window Master Switch

Precoated part
7.4 (76, 67 in.´lbf)
11 (115, 8.3)
52 (530, 38)
25 (260, 19)
5.0 (51, 44 in.´lbf)
5.4 (55, 48 in.´lbf)7.4 (76, 67 in.´lbf)
N´m (kgf´cm, ft´lbf): Specified torque
- BODYFRONT DOOR
BO-7
2087 Author
: Date
:
1997 SUPRA (RM502U)
FRONT DOOR
COMPONENTS

BO0QD-01
N08444
Vehicle
Outside Inside
N08445
N19391
: 6 Clips
N08456
Snap Snap
Setting NutLower Plate BO-8
- BODYFRONT DOOR
2088 Author
: Date
:
1997 SUPRA (RM502U)
DISASSEMBLY
1. REMOVE INSIDE HANDLE BEZEL
Remove the screw, then pull the inside handle bezel.
2. REMOVE TRIM BOARD
3. REMOVE THESE PARTS:
(a) Power window master switch
(b) Speaker
(c) Inside handle
(d) Inside handle plate
(e) Armrest bracket
(f) Service hole cover
(g) Weatherstrip
(h) Inside panel frame
(i) Door glass
Torque: 7.4 N´m (76 kgf´cm, 67 in.´lbf)
4. REMOVE DOOR BELT MOULDING
(a) Remove the clip.
(b) Using a screwdriver, remove the door belt moulding as
shown in the illustration.
HINT:
Tape the screwdriver tip before use.
5. REMOVE WINDOW GUIDE LOWER PLATE
(a) Remove the bolt of the lower plate and connector.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(b) Unlock the snap by pulling the lower plate.
(c) Remove the snap and lower plate from the stud bolt of the
lower bracket.
(d) Remove the setting nut from the lower bracket.

N19389
N19532
0 - 1.0 mm
(0 - 0.04 mm)
N19388
- BODYFRONT DOOR
BO-9
2089 Author
: Date
:
1997 SUPRA (RM502U)
6. REMOVE WINDOW REGULATOR
(a) Disconnect the connector.
(b) Remove the bolt, 2 nuts and window regulator.
Torque: 7.4 N´m (76 kgf´cm, 67 in.´lbf)
HINT:
At the time of reassembly, please refer to the following item.
Apply MP grease to the glass guide and rollers of the window
regulator.
7. REMOVE DOOR LOCK
(a) Disconnect the connector and clamp.
(b) Disconnect the link from the outside handle.
HINT:
At the time of reassembly, please refer to the following item.
After connecting the link, check that the clearance is within the
specification as shown in the illustration.
(c) Remove the 3 screws.
Torque: 5.0 N´m (51 kgf´cm, 44 in.´lbf)
HINT:
At the time of reassembly, please refer to the following item.
Apply adhesive to the 3 screws.
Part No.08833-00070, THREE BOND 1324 or equiva-
lent.
(d) Remove the door lock through the service hole.
HINT:
At the time of reassembly, please refer to the following item.
Apply MP grease to the sliding and rotating parts of the door
lock.
8. REMOVE THESE PARTS:
(a) Outside handle
(b) Door lock cylinder
(c) Outer rear view mirror

Z13646
A-A (Normal Roof)
A-A (Sport Roof) 6.9 ± 2
(0.272 ± 0.08)
A
B A
B
7 ± 2
(0.276 ± 0.08) 6.9 ± 2
(0.272 ± 0.08) 7 ± 2
(0.276 ± 0.08)
mm (in.) B-B
4.1 (0.161)9.1 ± 1.5
(0.358 ± 0.06)
- BODYFRONT DOOR
BO-1 1
2091 Author
: Date
:
1997 SUPRA (RM502U)
4. CHECK FRONT DOOR GLASS
Check the following items. If the conditions are not met, readjust
the glass.
(1) When you close the door with the glass fully closed,
the A-A, B-B sections are in the same condition as
shown in the illustration below.
(2) When you push the glass firmly from inside, the
glass stops at the roof drip moulding and does not
move.
(3) When you close the door with the glass fully closed,
the glass is not caught in the outside lip of the
weatherstrip and does not touch to the roof drip
moulding.
(4) With the door closed, the glass moves smoothly.
(5) The upper edge of the glass cannot be seen from
outside of the vehicle (edge touching roof side rail
weatherstrip).
(6) While the glass is being raised, the glass and roof
side rail weatherstrip are parallel, and the front and
rear door window upper stops touch at the same
time.

N08480
Door Window
Upper StopDoor Window
Upper Stop
Carrier Plate
Guide Lower Bracket
Lower Plate
N08475
Setting NutSnap
Lower Plate
N08477
N08845
BO-12
- BODYFRONT DOOR
2092 Author
: Date
:
1997 SUPRA (RM502U)
5. ADJUST FRONT DOOR GLASS

Upper side of glass - in/out
(1) Remove the lower plate bolt.
(2) Pull the lower plate so that the snap is unlocked.
(3) Remove the snap and lower plate.
(4) Adjust the glass by turning the setting nut.
(5) Reinstall the lower plate, snap and bolt.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)

Position (forward/rearward) the glass and attitude of
glass
Loosen the 3 bolts of the carrier plate and adjust.
Torque: 7.4 N´m (76 kgf´cm, 67 in.´lbf)

Position (vertical) the glass and attitude of glass
(when glass fully closed)
Adjust the door window upper stop.
Torque: 11 N´m (115 kgf´cm, 8.3 ft´lbf)

BO0R2-01
N19533
Tonneau Cover
Deck Trim Rear Cover
Coat Hook
Roof Side Inner Garnish
Tonneau Cover Clamp
Quarter Wheel House
Inner Cover
Deck Trim Side Board
Rear Seat
Outer Belt
Quarter Window
Glass
Roof Side Rail Weatherstrip
Retainer
Roof Side Rail Weatherstrip Speaker Grille Front Seat
Outer Belt
Deck Trim Side Service Hole Cover
Front Door Scuff
Inside Plate

Outside Garnish Seal Rear Seatback
5X
Sport Roof:Lower Back Service
Hole Cover
Removable Roof Stay
Stay Support Cover
Holder Garnish
Removable Roof Holder Luggage Compartment Mat
Spare Wheel Cover Rear Seat Cushion

Non-reusable partRear Quarter Trim Board
43 (440, 32)
25 (260, 19)
N´m (kgf´cm, ft´lbf) : Specified torque
- BODYQUARTER WINDOW GLASS
BO-37
2117 Author
: Date
:
1997 SUPRA (RM502U)
QUARTER WINDOW GLASS
COMPONENTS

BO0R3-01
N09045
Butyl Tape
: 3 Clips
N09040
Outside Garnish Seal BO-38
- BODYQUARTER WINDOW GLASS
2118 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE THESE PARTS:
(See pages BO-61)
(a) Tonneau cover
(b) Luggage compartment mat
(c) Spare wheel cover
(d) Rear seatback
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
(e) Removable roof stay RH and LH (Sport roof)
(f) Deck trim rear cover
(g) Removable roof holder (Sport roof)
(h) Quarter wheel house inner cover
(i) Speaker grille
(j) Deck trim side board
(k) Front door scuff inside plate
(l) Rear quarter trim board
(m) Front seat outer belt shoulder anchor
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
(n) Rear seat outer belt floor anchor
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
(o) Roof side inner garnish
(p) Rear roof headlining (Sport roof)
2. REMOVE ROOF SIDE RAIL WEATHERSTRIP
(a) Using a clip remover, remove the 3 clips from the rear side
of the weatherstrip.
(b) Remove the rear side of the weatherstrip from the retain-
er.
3. REMOVE ROOF SIDE RAIL WEATHERSTRIP RETAIN-
ER
Remove the outside garnish seal and retainer.