1997 TOYOTA SUPRA torque

LU054-01
P11778
5 mm
Hexagon
Wrench LU-26
- LUBRICATIONOIL NOZZLE (2JZ-GTE)
1473 Author
: Date
:
1997 SUPRA (RM502U)
INSTALLATION
1. INSTALL OIL NOZZLES (WITH RELIEF VALVES)
Using a 5 mm hexagon wrench, install the oil nozzle with the
bolt. Install the 6 oil nozzles.
Torque: 9.0 N´m (90 kgf´cm, 80 in.´lbf)
2. INSTALL CRANKSHAFT
(See page EM-88)

IG0152
P11795
Ohmmeter
P12177
Ohmmeter
- IGNITION (2JZ-GTE)IGNITION SYSTEM
IG-3
1497 Author
: Date
:
1997 SUPRA (RM502U)
(f) Clean the spark plugs.
If the electrode has traces of wet carbon, allow it to dry and then
clean with a spark plug cleaner.
Air pressure: Below 588 kPa (6 kgf/cm
2, 85 psi)
Duration: 20 seconds or less
HINT:
If there are traces of oil, remove it with gasoline before using the
spark plug cleaner.
(g) Using a 16 mm plug wrench, reinstall the 6 spark plugs.
Torque: 18 N´m (180 kgf´cm, 13 ft´lbf)
(h) Reinstall the ignition coils assemblies.
(See page IG-7)
3. INSPECT IGNITION COILS
(a) Remove the No.3 timing belt cover.
(b) Disconnect the ignition coil connectors.
(c) Using an ohmmeter, measure the resistance between the
terminals.
Primary coil resistance:
Cold0.54 - 0.84 W
Hot0.68 - 0.98 W
If the resistance is not as specified, replace the ignition coil.
(d) Reconnect the ignition coil connectors.
(e) Reinstall the No.3 timing belt cover.
4. INSPECT CAMSHAFT POSITION SENSORS
(a) Disconnect the camshaft position sensor connectors.
(b) Using an ohmmeter, measure the resistance between ter-
minals.
Resistance:
Cold835 - 1,400 W
Hot1,060 - 1,645 W
If the resistance is not as specified, replace the camshaft posi-
tion sensor.

IG04Z-02
P11575
P12362
IG-6
- IGNITION (2JZ-GTE)IGNITION COIL
1500 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE NO.3 TIMING BELT COVER
2. REMOVE PCV HOSES
3. DISCONNECT IGNITION COIL CONNECTORS
4. REMOVE BRACKET AND IGNITION COILS
ASSEMBLIES
Remove the 2 bolts and 2 ignition coils assembly.
Torque: 8.8 N´m (90 kgf´cm, 78 in.´lbf)
5. REMOVE IGNITION COILS FROM BRACKET
(a) Remove the rubber boot from the ignition coil.
(b) Remove the 2 screws and ignition coil.

IG052-02
P12179
- IGNITION (2JZ-GTE)CAMSHAFT POSITION SENSOR
IG-9
1503 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. DISCONNECT IAC VALVE CONNECTOR
2. DISCONNECT AIR HOSE FROM IAC VALVE
3. REMOVE ENGINE HANGER
Remove the 2 bolts, ground strap and engine hanger.
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
4. DISCONNECT CAMSHAFT POSITION SENSOR
CONNECTORS
5. REMOVE CAMSHAFT POSITION SENSORS
Remove the 4 bolts, 2 camshaft position sensors and 2 gas-
kets.
Torque: 8.8 N´m (90 kgf´cm, 78 in.´lbf)

IG055-02
P12330
P11800
IG-12
- IGNITION (2JZ-GTE)CRANKSHAFT POSITION SENSOR
1506 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE GENERATOR
(See page CH-8)
2. DISCONNECT CRANKSHAFT POSITION SENSOR
CONNECTOR
(a) Disconnect the sensor connector from the bracket.
(b) Disconnect the sensor connector from the wiring connec-
tor.
3. REMOVE CRANKSHAFT POSITION SENSOR
(a) Disconnect the wire clamp from the cylinder block.
(b) Remove the bolt and crankshaft position sensor.
Torque: 8.8 N´m (90 kgf´cm, 78 in.´lbf)

Z18832
Magnetic Switch AssemblyReturn SpringStarter Housing
Idler Gear
Steel Ball
Dust protector
Brush Holder
Dust ProtectorField Frame (Field Coil)Armature
Front Bearing Starter Clutch Assembly

Rear Bearing
O-Ring

O-RingBearing
End Cover
Terminal Insulator

Terminal C kit Part Magnetic Switch AssemblyContact Plate
Insulation Paper Terminal Insulator Terminal BoltTerminal Insulator Terminal
Bolt
Lead Clamp
End CoverPlungerLead
Terminal
Contact PlatePacking

Terminal 30 kit Part
O-Ring

Gasket
17 (170,12)
Wave Washer
Terminal Insulator
O-Ring17 (170,12)
N´m (kgf´cm, ft´lbf) : Specified torque

Non-reusable part
Wave Washer

O-Ring
- STARTINGSTARTER
ST-3
1510 Author
: Date
:
1997 SUPRA (RM502U)

B03052
37 N´m
B03053
200 N´m
125 N´m
B03054
58 N´m
175 N´m
MA01J-01
MA-8
- MAINTENANCEBODY
45 Author
: Date
:
1997 SUPRA (RM502U)
BODY
INSPECTION
1. TIGHTEN BOLTS AND NUTS ON CHASSIS AND
BODY
Tighten these parts:

Front seat - to -body mounting bolts
Torque: 37 N´m (375 kgf´cm, 27 ft´lbf)

Front suspension member-to-body mounting nuts
Torque:
Front side 125 N´m (1,280kgf´cm,92 ft´lbf)
Rear side 200 N´m (2,040 kgf´cm,148ft´lbf)

Rear suspension member-to-body mounting bolts
Torque: 175 N´m (1,790 kgf´cm, 129 ft´lbf)

Rear suspension member rear cushion - to - body
mounting bolts
Torque: 58 N´m (590 kgf´cm, 43 ft´lbf)
2. FINAL INSPECTION
(a) Check the operation of the body parts:

Hood:
Auxiliary catch operate properly
Hood locks securely when closed

Front doors:
Door lock operates properly
Doors close properly

Back door:
Door lock operates properly

Seats:
Seat adjusts easily and locks securely in any posi-
tion
Front seat back locks securely in any position
Folding-down rear seat backs lock securely
(b) Road test:

Check the engine and chassis for abnormal noises.

Check that the vehicle does not wander or pull to
one side.

Check that the brake work properly and do not drag.

Perform setting of the parking brake shoes and
disc.

RS06Y-02
R07002
2 Clips
- SUPPLEMENTAL RESTRAINT SYSTEMFRONT PASSENGER AIRBAG ASSEMBLY
RS-31
1970 Author
: Date
:
1997 SUPRA (RM502U)
INSTALLATION
NOTICE:
Never use airbag parts from another vehicle. When replac-
ing parts, replace them with new parts.
1. INSTALL FRONT PASSENGER AIRBAG ASSEMBLY
(a) Install the front passenger airbag assembly.
(b) Install the 2 bolts to instrument panel reinforcement.
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
(c) Install the 2 bolts to instrument panel.
Torque: 8.8 N´m (90 kgf´cm, 78 in.´lbf)
NOTICE:

Make sure that no foreign objects are trapped be-
tween the airbag bag, and within the module.

Do not damage the strap when installing the module.
NOTICE:
If the front passenger airbag assembly has been dropped,
or there are cracks, dents or other defects in the case or
connector, replace the front passenger airbag assembly
with a new one.
2. INSTALL THESE PARTS: (See page BO-50)
(a) Heater to register duct No.4
(b) Instrument panel box
3. CONNECT AIRBAG CONNECTOR
(a) Connect the airbag connector.
(b) Put the connector on the glove compartment door finish
plate.
(c) Install the glove compartment door finish plate to the
instrument panel box.