1997 SSANGYONG KORANDO transmission oil

SSANGYONG MY2002
5B-24 MANUAL TRANSMISSION
UNIT REPAIR
MAJOR UNIT
Disassembly Procedure
1. Remove the shift lever from the extension housing.
YAD5B470
YAD5B480
YAD5B500
YAD5B490
2. Install the removed transmission into a fixture.
3. Remove the drain plug and drain the oil. Using a
10 mm wrench, remove the clamp bolt and position
the offset lever in the 3-4 position of neutral.
Notice: Removal of the offset lever in a position
other than 3-4 of neutral will be difficult.
4. Using a pin punch and a hammer, remove the roll
pin to remove the shift lever from the offset lever.
5. Using a 15 mm wrench, remove the 8 bolts from
the extension housing.
6. Separate the extension housing from the case and
shift cover.
Separate the offset lever from the shift.
Notice: Do not remove the offset lever while the
extension housing is still assembled to the case.

MANUAL TRANSMISSION 5B-25
SSANGYONG MY2002
7. Remove the offset lever from the extension
housing with the detent ball and spring.
8. Remove the roll pin from either the offset lever or
extension housing.
YAD5B510
YAD5B520
YAD5B540
YAD5B530
9. Remove the counter shaft thrust race and bearing.
10. Carefully remove the oiling funnel from the end of
the counter shaft.
11. Using a 10 mm wrench, remove the 10 bolts from
the shift cover.
Notice: For assembly, note the location of the two
bolts.
12. Lift up the shift cover after sliding it toward the
drain plug about 3 cm. At this time remove sealer
bond.

MANUAL TRANSMISSION 5B-31
SSANGYONG MY2002
7. Install the counter shaft rear bearing outer race,
shim and retainer.
Installation Notice
Notice: Using a punch and hammer, bend the lock
tabs on the retainer.
YAD5B750
YAD5B760
YAD5B770
8. Install the following parts :
Install the main shaft into case.
Install the main shaft rear bearing outer race
into the rear of the case.
Install the 4th speed blocking ring onto the front
of the main shaft.
Install the input shaft onto the front of the main
shaft.
Install the input bearing retainer without shim
onto the front of the case.
Using a torque wrench, tighten the 4 bolts.
Installation Notice
9. Install the 5th speed drive gear and blocking ring
on the counter shaft.
10. Install the 5th synchronizer and rail/fork.
11. Install the 5th synchronizer snap ring and oiling
funnel.
Tightening Torque 20 Nm (15 lb-ft)
Tightening Torque 20 Nm (15 lb-ft)

TRANSFER CASE 5D1-67
SSANGYONG MY2002
KAA5D260
KAA5D270
TRANSFER CASE CONTROL UNIT
(TCCU)
Removal and Installation Procedure
1. Turn the ignition switch to OFF.
2. Disconnect two connectors from the TCCU under
the driver seat.
3. Remove two bolts and the TCCU.
Installation Notice
Tightening Torque 10 Nm (7 lb-ft)
When replacing the TCCU, it is required to a
cod-ing correspondent with the vehicle
specification. Refer to “TCCU Coding” in this
section.
4. Installation should follow the removal procedure
in the reverse order.
TRANSFER CASE
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Lift the vehicle and make sure safety.
Notice: Be careful not to touch the catalytic
converter which is very hot after driving or engine
running.
3. Remove the drain plug and drain the transfer case
oil. Refer to “Oil Replacement” in this section.
Installation Notice
4. Disconnect the transmission extension wiring con-
nector on backside of transfer case.
5. Disconnect shift motor and clutch coil connector
(black 7 pin) on upper backside of transfer case.
6. Disconnect front and rear speed sensor connector
(white 7 pin).
7. Disconnect speedometer sensor connector.
Tightening Torque19 - 30 Nm
(14 - 22 lb-ft)

SSANGYONG MY2002
9A-22 BODY WIRING SYSTEM
W/H TRANSMISSION
Automatic Transmission
3 Transmission
4 T/M Lever
5 Inhibitor switch
6 Micro switch (Diesel E/G)7 Throttle position sensor (Diesel E/G)
8 Engine oil pressure switch
9 Engine speed sensor (Diesel E/G)
YAD9B350

BODY WIRING SYSTEM 9A-23
SSANGYONG MY2002
Manual Transmission
1 C302
2 Back up switch
3 Micro switch4 Engine oil pressure switch
5 Engine speed sensor
YAD9B350

2-14 2-14 2-14 2-14
2-14
ELECTRICAL WIRING DIAGRAMS ELECTRICAL WIRING DIAGRAMSELECTRICAL WIRING DIAGRAMS ELECTRICAL WIRING DIAGRAMS
ELECTRICAL WIRING DIAGRAMS10) 10)10) 10)
10)
W/H TRANSMISSION W/H TRANSMISSIONW/H TRANSMISSION W/H TRANSMISSION
W/H TRANSMISSION
1. C301
2. C302 (Diesel E/G)
3. Transmission
4. T/M Lever
5. Inhibitor switch
6. Micro switch (Diesel E/G)
7. Throttle position sersor (Diesel E/G)
8. Engine oil pressure switch
9. Engine speed sensor (Diesel E/G)1. C302
2. Back up switch
3. Micro switch
4. Engine oil pressure switch
5. Engine speed sensor • AUTOMATIC TRANSMISSION MANUAL TRANSMISSION

CONTENTS CONTENTSCONTENTS CONTENTS
CONTENTS
1. 1.1. 1.
1.
ST STST ST
ST
AR ARAR AR
AR
TING & CHARGING SYSTEM TING & CHARGING SYSTEMTING & CHARGING SYSTEM TING & CHARGING SYSTEM
TING & CHARGING SYSTEM
........................................................................................... ...................................................................................................................................................................................... ...........................................................................................
...........................................................................................
5-6 5-6 5-6 5-6
5-6
1) DIESEL..................................................................................................................................................................... 5-6
2) GASOLINE.................................................................................................................................................................. 5-8
2. 2.2. 2.
2.
DIAGNOSIS CONNECTOR DIAGNOSIS CONNECTORDIAGNOSIS CONNECTOR DIAGNOSIS CONNECTOR
DIAGNOSIS CONNECTOR
........................................................................................................ ................................................................................................................................................................................................................ ........................................................................................................
........................................................................................................
5-10 5-10 5-10 5-10
5-10
1) DIESEL................................................................................................................................................................... 5-10
2) GASOLINE.............................................................................................................................................................. 5-12
(1) W/O EURO III .................................................................................................................................................................................... 5-12
(2) W/ EURO III ....................................................................................................................................................................................... 5-14
3. 3.3. 3.
3.
PRE-HEA PRE-HEAPRE-HEA PRE-HEA
PRE-HEA
TING SYSTEM TING SYSTEMTING SYSTEM TING SYSTEM
TING SYSTEM
............................................................................................................ ........................................................................................................................................................................................................................ ............................................................................................................
............................................................................................................
5-16 5-16 5-16 5-16
5-16
4. 4.4. 4.
4.
EGR (EXHA EGR (EXHAEGR (EXHA EGR (EXHA
EGR (EXHA
UST GAS RECIRCULA UST GAS RECIRCULAUST GAS RECIRCULA UST GAS RECIRCULA
UST GAS RECIRCULA
TION) SYSTEM TION) SYSTEMTION) SYSTEM TION) SYSTEM
TION) SYSTEM
............................................................... .............................................................................................................................. ...............................................................
...............................................................
5-18 5-18 5-18 5-18
5-18
1) MANUAL TRANSMISSION .................................................................................................................................... 5-18
2) AUTOMATIC TRANSMISSION.............................................................................................................................. 5-20
5. 5.5. 5.
5.
ECM (ELECTRONIC CONTROL MODULE) : E23 MSE ECM (ELECTRONIC CONTROL MODULE) : E23 MSEECM (ELECTRONIC CONTROL MODULE) : E23 MSE ECM (ELECTRONIC CONTROL MODULE) : E23 MSE
ECM (ELECTRONIC CONTROL MODULE) : E23 MSE
......................................................... .................................................................................................................. .........................................................
.........................................................
5-22 5-22 5-22 5-22
5-22
1) SENSOR (CRANK SHAFT POSITION, ACCELERATION PEDAL), THROTTLE MOTOR & SENSOR, IGNTION
COIL & SPARK PLUG ........................................................................................................................................... 5-22
SECTION 5 SECTION 5SECTION 5 SECTION 5
SECTION 5
ELECTRICAL WIRING DIAGRAMS ELECTRICAL WIRING DIAGRAMSELECTRICAL WIRING DIAGRAMS ELECTRICAL WIRING DIAGRAMS
ELECTRICAL WIRING DIAGRAMS