1997 SSANGYONG KORANDO torque

SSANGYONG MY2002
5D2-22 TRANSFER CASE (PART TIME - 4408)
KAA5D270
KAA5D280
TRANSFER CASE ASSEMBLY
1. Disconnect the negative terminal from the battery.
2. Lift up the vehicle and fix it safely.
3. Remove the damper mounting bolt.
4. Remove the drain plug and drain the oil.
Reinstall the drain plug.
Installation Notice
KAA5D290
5. Remove the breather hose.
6. Disconnect the speedometer cable connector and
other cable connectors and wiring harnesses.20 - 30 Nm
(15 - 22 lb-ft)
30 - 40 Nm
(22 - 30 lb-ft)
4 - 6 Nm
(35 - 53 lb-in)
Drain Plug Tightening
Torque
Damper Tightening
Torque
Fill plug Tightening
Torque

TRANSFER CASE (PART TIME - 4408) 5D2-23
SSANGYONG MY2002
KAA5D300
KAA5D310
KAA5D320
7. Support the transfer case with jack and remove
the front and rear propeller shafts from the transfer
case.
Installation Notice
81 - 89 Nm
(60 - 66 lb-ft)
70 - 90 Nm
(52 - 66 lb-ft)
Tightening
TorqueFront
Rear
12 - 23 Nm
(9 - 17 lb-ft)
6 - 8 Nm
(53 - 71 lb-in)Tightening Torque(1)
Tightening Torque(2)
Tightening Torque35 - 60 Nm
(26 - 44 lb-ft) 8. Remove the center mounting nuts and end sides
mounting bolts of the cross member and then
remove the cross member.
Installation Notice
9. Remove the transfer case by removing the bolts
attaching the transfer case to the transmission.
Installation Notice
Notice: Apply long-term grease to the inner spline
of the transfer case input shaft.
10. Installation should follow the removal procedure
in the reverse order.

SSANGYONG MY2002
5D2-24 TRANSFER CASE (PART TIME - 4408)

yyyy yyyy

yyyy yyyy

yyyy yyyy
KAA5D330
TCCU
1. Disconnect the negative terminal from the battery.
KAA5D340
KAA5D350
KAA5D360
2. Remove the TCCU connector.
3. Remove the TCCU mounting bolt and remove the
TCCU.
TCCU installation position : Under the driver’s
seat
4. Installation should follow the removal procedure
in the reverse order.
Notice: Be careful not to give any impact to the
TCCU body.
Installation Notice
Tightening Torque 10 Nm (89 lb-ft)

TRANSFER CASE (PART TIME - 4408) 5D2-37
SSANGYONG MY2002
KAA5D810
KAA5D820
Adapter, Input Shaft and Carrier
1. Place the planet carrier assembly on work bench
to be the retaining ring mounting groove upward.
2. Install the sun gear with the hub end up into the
planet carrier assembly and rotate the sun gear
to make sure that gears are fully engaged.
3. Align the tabs and install the thrust plate into the
planet carrier assembly.
4. Install the retaining ring to the planet carrier
assembly.
5. Press the needle bearing into the input shaft and
press the new sleeve bearing into the input shaft
assembly.
6. Install the planet carrier assembly onto the input
shaft and install the thrust washer. Press the
bearing over input shaft.
7. After pressing the bearing, install the retaining
ring.
8. Press the pin into the front adapter.
9. Slowly press the oil seal into the front adapter.
10. Install the front adapter assembly.
Notice: After installation, make sure that snap ring
is correctly installed into the groove.
11. Position the input shaft assembly over front cover
and engage into the bearing groove by expanding
the ends of snap ring.
12. Apply 1.6mm bead of sealant on the mounting
face for the transfer case and tighten the 6 bolts.
13. Install the breather.
Installation Notice
Tightening Torque
28 - 40 Nm
(21 - 30 lb-ft)
4 - 7 Nm
(35 - 62 lb-in)
Item
6 Bolts
Breather
Front Output Shaft
Cross Sectional View

SSANGYONG MY2002
5D2-38 TRANSFER CASE (PART TIME - 4408)
KAA5D830
KAA5D840
KAA5D850
Input Shaft
Cross Sectional View
Tightening Torque346 - 380 Nm
Front Output Shaft
1. Install the deflector on the yoke.
2. Position the output shaft in transfer case and install
the companion flange assembly, oil seal, washer
and nut.
3. Holding the companion flange, tighten the nut.
Installation Notice
Reduction Shift Parts
1. Install the new pin, roller and retainer into the
reduction shift fork.
2. Press the pin, roller and retainer into the reduction
spilt fork bore completely.
Notice: Make sure that the cam roller turns freely.
3. Install the 2 fork facing on the reduction shift fork
assembly.
4. Install the reduction shift fork onto the previously
installed reduction hub in the transfer case.
5. Install the output shaft spline into the reduction
hub and engage the output shaft end with input
shaft bearing.
Notice: For installation of the output shaft,
assemble the oil pump temporarily.

TRANSFER CASE (PART TIME - 4408) 5D2-39
SSANGYONG MY2002
KAA5D860
KAA5D870
Oil Pump
1. Install the pump front cover to be the “TOP” mark
down and turn the cover to be the “TOP” mark up
when installed in vehicle.
2. Install the 2 pump pins and spring to the output
shaft.
Notice: Flat surface of the pins must point out
and align the center line of pins and spring.
3. Connect the hose coupling to the strainer coupling
and install the strainer foot into the transfer case
slot.
Notice: The hose coupling must face the pump
assembly.
4. Install the pump housing to be the ‘REAR’ mark
up and seat the 2 pump pins inside of the pump
housing by moving pump pins inward and
compressing the spring.
5. Tighten the hose to pump housing by hose clamp.
6. Position the pump rear cover to be the TOP REAR
mark up and located at the top of transfer case
when installed in vehicle. Position the pump
retainer on the cover so that tab on the retainer is
in notch in the transfer case. Apply Loctite to the
bolts and tighten the bolts with turning the output
shaft by hand to make the pump pins move freely.
Installation Notice
Tightening Torque4 - 8.5 Nm
(35 - 75.5 lb-in)
Drive Chain
1. Position the drive sprocket to the rear output shaft
end and driven sprocket to the front output shaft
end.
2. Install the drive chain onto the sprocket.
3. Holding each sprocket to be the drive chain tight
and parallel with transfer case, install the drive
chain assembly to the output shafts.
4. Rotate the driven sprocket slightly to engage
splines on the front output shaft.
5. Install the spacer to the front output shaft and insert
the snap ring into the shaft groove over spacer.

TRANSFER CASE (PART TIME - 4408) 5D2-41
SSANGYONG MY2002
KAA5D900
Tightening Torque8 - 11 Nm
(71 - 97 lb-in)
Cover
1. Position the cover to be the open end up on the
work table.
2. Position the end of needle bearing to be
identification mark up and press into the cover
until upper end of bearing is 40.47 - 40.97 mm
below cover face that contacts with transfer case.
3. Press the ball bearing into the cover and install
the snap ring .
4. Install remaining parts as follows.
Install the 4 O-rings on the stud bolts of the
clutch coil assembly.
Install the clutch coil assembly inside the cover
and tighten 3 nuts.
Installation Notice
Install the bearing and motor bearing into the
cover.
KAA5D910
Cover Assembly
1. Install the return spring over rail shaft in the transfer
case.
2. Insert the magnet into the transfer case slot.
3. Apply 1.6 mm bead of Loctite RTV 598 to the
transfer case mounting surface.
Notice: For installation of cover, align the transfer
case with cover not to use excessive force.
4. Install the cover onto the transfer case as follows:
Align the cover bores with transfer case pins.
Align the cover bearings with output shafts.
Align the cover blind hole with rail shaft and
make sure that return spring is not cocked.

SSANGYONG MY2002
5D2-42 TRANSFER CASE (PART TIME - 4408)
5. Tighten 9 bolts positioning identification tag and
wiring clip.
Installation Notice
6. Install the speed gear over output shaft spline in
the cover assembly.
7. Press the new oil seal into the cover assembly.
Tightening Torque28 - 40 Nm
(21 - 30 lb-ft)
KAA5D920
KAA5D930
KAA5D940
External Electric Shift
1. Align the motor with shift shaft and position the
motor assembly onto the cover.
2. Install the motor to the shift shaft and contact
cover and rotate the motor clockwise direction to
check correct engagement.
3. Insert the O-ring on the speed sensor assembly
to the cover.
4. Install the bracket to the motor assembly and
tighten 3 bolts.
Installation Notice
Tightening Torque8 - 11 Nm
(71 - 97 lb-in)