1996 TOYOTA RAV4 Generator

IG06K−02
B11571
− IGNITIONCRANKSHAFT POSITION SENSOR
IG−15
1996 RAV4 (RM447U)
REMOVAL
1. DISCONNECT CRANKSHAFT POSITION SENSOR
CONNECTOR FROM GENERATOR DRIVE BELT AD-
JUSTING BAR
2. REMOVE NO.1 TIMING BELT COVER
(See page EM−15)
3. REMOVE CRANKSHAFT POSITION SENSOR
Remove the bolt and disconnect the crankshaft position sensor.

IG06M−02
IG−16
− IGNITIONCRANKSHAFT POSITION SENSOR
1996 RAV4 (RM447U)
INSTALLATION
1. INSTALL CRANKSHAFT POSITION SENSOR
Install the crankshaft position sensor with the bolt.
Torque: 9.5 N·m (97 kgf·cm, 84 in.·lbf)
2. INSTALL NO.1 TIMING BELT COVER (See page EM−20)
3. CONNECT CRANKSHAFT POSITION SENSOR CONNECTOR TO GENERATOR DRIVE BELT AD-
JUSTING BAR

P04349
S02326
Engine
Hanger
No.1
S01635
SST
S01599
S01581
LU−8
− LUBRICATIONOIL PUMP
1996 RAV4 (RM447U)
7. REMOVE OIL PAN BAFFLE PLATE AND OIL STRAIN-
ER
Remove the 2 bolts, 2 nuts, oil strainer, baffle plate and gasket.
8. SUSPEND ENGINE WITH ENGINE SLING DEVICE
Install a engine hanger No. 1 in the correct direction.
Part No. :
Engine hanger No. 1 12281−74060
Bolt 91611−B1020
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
9. REMOVE TIMING BELT (See page EM−15)
10. REMOVE NO.2 IDLER PULLEY AND CRANKSHAFT
TIMING PULLEY (See page EM−81)
11. REMOVE OIL PUMP PULLEY
Using SST, remove the nut and pulley.
SST 09960−10010 (09962−01000, 09963−00600)
12. REMOVE CRANKSHAFT POSITION SENSOR
(a) Disconnect the connector from the generator drive belt
adjusting bar.
(b) Remove the bolt and crankshaft position sensor.
13. REMOVE OIL PUMP
(a) Remove the 12 bolts.

LU0O5−01
Z17341
A
B AA A
A A
A
AAA
B
S01599
S01633
SST LU−14
− LUBRICATIONOIL PUMP
1996 RAV4 (RM447U)
INSTALLATION
1. INSTALL OIL PUMP
Install a new gasket and the oil pump with the 12 bolts. Uniform-
ly tighten the bolts is several passes.
Torque: 8.8 N·m (90 kgf·cm, 78 in.·lbf)
HINT:
Each bolt length is indicated in the illustration.
Bolt length:
A: 25 mm (0.98 in.)
B: 35 mm (1.38 in.)
2. INSTALL CRANKSHAFT POSITION SENSOR
(a) Install the crankshaft position sensor with the bolt.
Torque: 8.8 N·m (90 kgf·cm, 78 in.·lbf)
(b) Connect the connector to the generator drive belt adjust-
ing bar.
3. INSTALL OIL PUMP PULLEY
(a) Align the cutouts of the pulley and shaft, and slide on the
pulley.
(b) Using SST, install the pulley nut.
SST 09960−10010 (09962−01000, 09963−00600)
Torque: 24 N·m (245 kgf·cm, 18 ft·lbf)
4. INSTALL CRANKSHAFT TIMING PULLEY AND NO.2
IDLER PULLEY (See page EM−20)
5. INSTALL TIMING BELT (See page EM−20)
6. REMOVE ENGINE SLING DEVICE
Remove the engine hanger No.1.

LU06A−03
S01365
S01359
SST
S01366
LU−18
− LUBRICATIONOIL COOLER
1996 RAV4 (RM447U)
REMOVAL
1. REMOVE RH ENGINE UNDER COVER
2. DRAIN ENGINE COOLANT
3. REMOVE FRONT EXHAUST PIPE (See page EM−33)
4. REMOVE GENERATOR (See page CH−7)
5. REMOVE OIL DIPSTICK
6. REMOVE EXHAUST MANIFOLD AND FRONT TWC
ASSEMBLY (See page EM−33)
7. REMOVE WATER BYPASS PIPE HEAT PROTECTOR
Remove the bolt, 2 nuts and heat protector.
8. REMOVE OIL FILTER
Using SST, remove the oil filter.
SST 09228−06501
9. REMOVE OIL COOLER
(a) Disconnect the 2 water bypass hoses from the oil cooler.
(b) Remove the union bolt and plate washer.
(c) Remove the nut and oil cooler.
(d) Remove the O−ring from the oil cooler.

LU06C−02
LU−20
− LUBRICATIONOIL COOLER
1996 RAV4 (RM447U)
INSTALLATION
1. INSTALL OIL COOLER
(a) Clean the oil cooler contact surface on the oil cooler
mounting.
(b) Install a new O−ring to the oil cooler.
(c) Temporarily install the oil cooler with the nut.
(d) Apply a light coat of engine oil on the threads and under
the head of the relief valve.
(e) Install the plate washer and union bolt.
Torque: 78 N·m (800 kgf·cm, 58 ft·lbf)
(f) Tighten the nut.
Torque: 8.8 N·m (90 kgf·cm, 78 in.·lbf)
(g) Connect the 2 water bypass hoses to the oil cooler.
2. INSTALL OIL FILTER
3. INSTALL WATER BYPASS HOSE HEAT PROTECTOR
Install the heat protector with the bolt and 2 nuts.
4. INSTALL EXHAUST MANIFOLD AND FRONT TWC AS-
SEMBLY (See page EM−55)
5. INSTALL OIL DIPSTICK
6. INSTALL GENERATOR (See page CH−19)
7. INSTALL FRONT EXHAUST PIPE (See page EM−55)
8. FILL WITH ENGINE COOLANT
9. START ENGINE AND CHECK FOR LEAKS
10. CHECK ENGINE OIL LEVEL
11. INSTALL RH ENGINE UNDER COVER