1996 TOYOTA LAND CRUISER INSTRUMENT PANEL

A00184
STARTIGT
(+)(−)
BE6653
P24674
FI6605
IGT signal waveform
5 m sec/Division (Idling)
IGT
IGF
2 V/Div.
0V 0V
−
DIAGNOSTICS ENGINE
DI−99
1996 LAND CRUISER (RM451U)
4 Check for open and short in harness and connector in IGT signal circuit betwe\
en
ECM and igniter (See page IN−28).
NG Repair or replace harness or connector.
OK
5 Check voltage between terminals IGT of ECM connector and body ground.
PREPARATION:
Remove instrument panel speaker No.1 panel (See page
SF−65 ).
CHECK:
Measure voltage between terminal IGT of ECM connector and
body ground when engine is cranked.
OK:
Voltage: More than 0.1 V and less than 4.5 V
Reference: INSPECTION USING OSCILLOSCOPE
During cranking or idling, check waveforms between terminals
IGT and E1 of engine control module.
HINT:
The correct regulator waveforms are as shown.
NG Check and replace ECM (See page IN−28 ).
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00184
STARTIGT
(+)(−)
BE6653
P24674
A00186
ON and START
3
BE6653
P24675
DI−100
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
6 Disconnect igniter connector and check voltage between terminals IGT of ECM
connector and body ground.
PREPARATION:
(a) Disconnect igniter connector.
(b) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
CHECK:
Measure voltage between terminal IGT of ECM connector and
body ground when engine is cranked.
OK:
Voltage: More than 0.1 V and less than 4.5 V
OK Check and replace ECM (See page IN−28 ).
NG
7 Check voltage between terminal 3 of igniter connector and body ground.
PREPARATION:
Disconnect igniter connector.
CHECK:
Measure voltage between terminal 3 of igniter connector and
body ground, when ignition switch is turned to ”ON” and
”START” position.
OK:
Voltage: 9 − 14 V
NG Check and repair igniter power source circuit.
OK
8 Check for open and short in harness and connector between ignition switc\
h and ignition coil, ignition coil and igniter (See page IN−28).
NG Repair or replace harness or connector.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE6053P24676A08534
LOCK
(+)
(−)
BATT
P22346
R/B No.2
EFI Fuse
DI−106
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check voltage between terminal BATT of ECM connector and body ground.
PREPARATION:
Remove the instrument panel speaker No.1 panel
(See page SF−65 ).
CHECK:
Measure voltage between terminal BATT of ECM connector
and body ground.
OK:
Voltage 9 − 14 V
OK Check and replace ECM (See page IN−28 ).
NG
2 Check EFI fuse.
PREPARATION:
Remove EFI fuse from R/B No.2.
CHECK:
Check continuity of EFI fuse.
OK:
Continuity
NG Check for short in all the harness and components connected to EFI fuse.
OK
Check and repair harness or connector
between battery, EFI fuse and ECM.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P24677
32
4
10 98 6
51
7
A00188
ON
NSW
(+)
(−)
BE6653
P24678
−
DIAGNOSTICS ENGINE
DI−109
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check park/neutral position switch.
PREPARATION:
Disconnect park/neutral position switch connector.
CHECK:
Check continuity between each terminal shown below when the
shift lever is positioned to each range.
OK:
Shift PositionTerminal No. to continuityTerminal No. to continuity
P4 − 75 − 6
R4 − 8−
N4 − 105 − 6
D4 − 9−
22 − 4−
L3 − 4−
NG Replace park/neutral position switch.
OK
2 Check voltage between terminal NSW of ECM connector and body ground.
PREPARATION:
Remove instrument panel speaker No.1 panel
(See page SF−65 ).
CHECK:
(a) Turn ignition switch ON.
(b) Measure voltage between terminal NSW of ECM connec-
tor and body ground when the shift lever is positioned to
the following positions.
OK:
Shift lever positionP or NL, 2, D or R
Voltage0 V9 − 14 V
OK Check and replace ECM (See page IN−28 ).
NG
Check for open and short in harness and
connector between ECM and park/neutral
position switch (See page IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00189
ON
E1 +B
(−) (+)
BE6653
P24679
A00190
ON
IGSW
(+)
(−)
BE6653
P24680
−
DIAGNOSTICS ENGINE
DI−111
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check voltage between terminals +B and E1 of the ECM connector.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel
(See page SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals +B and E1 of the ECM con-
nector.
OK:
Voltage: 9 − 14 V
OK Proceed to next circuit inspection shown on matrix chart (See page DI−19 ).
NG
2 Check for open in harness and connector between terminal E1 of ECM conne\
ctor and body ground (See page IN−28).
NG Repair or replace harness or connector.
OK
3 Check voltage between terminal IGSW of ECM connector and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals IGSW of ECM and body
ground.
OK:
Voltage: 9 − 14 V
OK Go to step 6.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P24681
DI−11 2
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
4 Check IGN fuse from fuse block.
NG Check for short in all the harness and
components connected to IGN fuse.
OK
5 Check ignition switch.
PREPARATION:
(a) Remove instrument lower finish panel.
(b) Remove instrument cluster finish center panel No.2.
CHECK:
Check continuity between terminals.
OK:
Shift PositionTerminal No. to continuityTerminal No. to continuity
LOCK−−
ACC3 − 4−
ON2 − 3 − 46 − 11
START1 − 2 − 45 − 6 − 11
NG Replace ignition switch.
OK
Check for open and short in harness and
connector between battery and ignition
switch and ECM.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00191
ONMRLY(+)
(−)
BE6653
P24682
−
DIAGNOSTICS ENGINE
DI−11 3
1996 LAND CRUISER (RM451U)
6 Check voltage between terminal MREL of ECM connector and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel
(See page SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminal MREL of ECM and body
ground.
OK:
Voltage: 9 − 14 V
NG Check and replace ECM.
OK
7 Check EFI fuse (Marking: EFI) (See page DI−105).
NG Check for short in all the harness and
components connected to EFI fuse.
OK
8 Check EFI main relay (Marking: EFI) (See page SF−54).
NG Replace EFI main relay (Marking: EFI).
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P09401
−
DIAGNOSTICS ENGINE
DI−11 7
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
TOYOTA hand −held tester
1 Connect the TOYOTA hand −held tester and check operation of fuel pump.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and TOYOTA hand −held tester
main switch ON.
(d) Use ACTIVE TEST mode to operate the fuel pump.
CHECK:
Check for fuel pressure in the fuel return hose when it is pinched
off.
OK:
There is pressure in the fuel return hose.
HINT:
At this time, you will hear a fuel flowing noise.
OK Go to step 4.
NG
2 Check circuit opening relay (See page SF−56 ).
NG Replace circuit opening relay.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010