1996 TOYOTA LAND CRUISER INSTRUMENT PANEL

A00165
ON
#10 #20 #40 #50
#30 #60
BE6653
P24661
−
DIAGNOSTICS ENGINE
DI−57
1996 LAND CRUISER (RM451U)
2 Check voltage of ECM terminal for injector of failed cylinder.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between applicable terminal of ECM connec-
tor and body ground.
OK:
Voltage: 9 − 14 V
OK Go to step 4.
NG
3 Check injector of misfiring cylinder (See page SF−29).
NG Replace injector.
OK
Check for open and short in harness and con-
nector between injector and ECM (See page
IN−28 ).
4 Check fuel pressure (See page SF−6 ).
NG Check and repair fuel pump, pressure regulator,
fuel pipe line and filter (See page SF−1).
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE6053P24662A08533
OFF
(−) (+)
KNK 1
KNK 2E5 Connector
DI−60
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
HINT:
DTC P0325 is for the knock sensor circuit on the front side.
DTC P0330 is for the knock sensor circuit on the rear side.
1 Check continuity between terminal KNK1, KNK2 of ECM connector and body
ground.
PREPARATION:
(a) Remove the instrument panel speaker No.1 panel (See
page SF−65 ).
(b) Disconnect the E5 connector of ECM.
CHECK:
Measure resistance between terminal KNK1, KNK2 of ECM
connector and body ground.
HINT:
Connect terminal KNK1 to knock sensor 1.
Connect terminal KNK2 to knock sensor 2.
OK:
Resistance: 1 MΩ or higher
OK Go to step 3.
NG
2 Check knock sensor (See page SF−62 ).
NG Replace knock sensor.
OK
3 Check for open and short in harness and connector between ECM and knock sensor (See page IN−28 ).
NG Repair or replace harness or connector.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00168
ON
EGR Gas Temp.
Sensor ECM
19 9
1
2
BE6653
FI7055 THG
E2
E4
E5 5V
−
DIAGNOSTICS ENGINE
DI−71
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
TOYOTA hand −held tester
1 Connect the TOYOTA hand −held tester and read value of EGR gas temp. value.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and push the TOYOTA hand −held tester main switch ON.
CHECK:
Read EGR gas temp. on the TOYOTA hand−held tester.
OK:
EGR gas temp.: 10° C (50°F) or more
HINT:
If there is and open circuit, the TOYOTA hand−held tester indicates 3.1 °C (37.6° F).
OK Go to step 4.
NG
2 Check for open in harness or ECM.
PREPARATION:
(a) Disconnect the EGR gas temp. sensor connector.
(b) Connect sensor wire harness terminals together.
(c) Turn ignition switch ON.
CHECK:
Read EGR gas temp. on the TOYOTA hand−held tester.
OK:
EGR gas temp.: Approx. 157.5° C (315.5°F)
OK Confirm good connection at sensor. If OK, replace EGR gas temp. sensor.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00169
ON
EGR Gas Temp.
Sensor ECM
1
2 19
9
THG E2
BE6653
FI7057
P22167 E4
E5
THG E2 5V
DI−72
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
3 Check for open in harness or ECM.
PREPARATION:
(a) Remove the instrument panel speaker No.1 panel (See
page SF−65 ).
(b) Connect between terminals THG and E2 of ECM connec-
tor.
HINT:
EGR gas temp. sensor connector is disconnected.
Before checking, do a visual check and contact pressure check
for the ECM connector (See page IN−28).
CHECK:
Read EGR gas temp. on the TOYOTA hand−held tester.
OK:
EGR gas temp.: Approx. 157.5° C (315.5°F)
OK Open in harness between terminals E2 or THG. Repair or replace harness.
NG
Confirm connection at ECM.
If OK, replace ECM (See page IN−28).
4 Check the connection of the vacuum hose, EGR hose (See page EC−11).
NG Repair or replace.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00170
System : ON
System : OFF Air
GE
Air GE
P22963
P22964
−
DIAGNOSTICS ENGINE
DI−73
1996 LAND CRUISER (RM451U)
5 Check the VSV for EGR.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and TOYOTA hand −held tester
main switch ON.
(d) Select the ACTIVE TEST mode on the TOYOTA hand −
held tester.
CHECK:
Check operation of VSV, when it is operated by the TOYOTA
hand −held tester.
OK:
EGR system is ON:
Air does not flow from pipe G to pipe E.
EGR system is OFF:
Air from pipe G is flowing out through pipe E.
OK Go to step 7.
NG
6 Check operation of the VSV for EGR (See page SF−60).
NG Replace VSV for EGR.
OK
Check for open in harness and connector be-
tween VSV and ECM (See page IN−28).
7 Check EGR vacuum modulator (See page EC−11 ).
NG Repair or replace.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−74
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
8 Check EGR valve (See page EC−11).
NG Repair or replace.
OK
9 Check value of EGR gas temp. sensor.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and TOYOTA hand −held tester main switch ON.
(d) Select the ACTIVE TEST mode on the TOYOTA hand−held tester. (EGR system ON)
(e) Race the engine at 4,000 rpm for 3 mins.
CHECK:
Measure the EGR gas temp. while racing engine at 4,000 rpm.
OK:
EGR gas temp. after 3 mins.: 140° C (284°F) or more
NG Replace EGR gas temp. sensor.
OK
Check and replace ECM (See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00172
ON
THG E2 (+)(−)
BE6653
P24667
DI−76
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
3 Check for open in harness or ECM.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals of THG and E2 of ECM
connector.
HINT:
EGR gas temp. sensor connector is disconnected.
OK:
Voltage: 4.5 − 5.5 V
OK Open in harness between terminals E2 or THG. Repair or replace harness.
NG
Confirm connection at ECM.
If OK, replace ECM (See page IN−28).
4 Check connection of vacuum hose, EGR hose (See page EC−11).
NG Repair or replace.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00173
ON
EGR ONOFF
(1) VSV is ON:
(2) VSV is OFF: Air
GE
Air GE
BE6653
P22905
P22963
P22964
−
DIAGNOSTICS ENGINE
DI−77
1996 LAND CRUISER (RM451U)
5 Check the VSV for EGR.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Check VSV function.
(1) Connect between terminal EGR of ECM and bodyground (ON).
(2) Disconnect between terminal EGR of ECM and
body ground (OFF).
OK:
(1) VSV is ON:
Air does not flow from pipe G to pipe E.
(2) VSV is OFF:
Air from pipe G is flows out through pipe E.
OK Go to step 7.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010