1996 TOYOTA LAND CRUISER Drive

MA04U−01
P04771
−
MAINTENANCE ENGINE
MA−5
45
Author: Date:
1996 LAND CRUISER (RM451U)
ENGINE
INSPECTION
HINT:
Inspect these items when the engine is cold.
1. INSPECT DRIVE BELT (See page CH−2)
2. INSPECT AIR FILTER
(a) Visually check that the air cleaner element is not exces- sively dirty, damaged or oily.
If necessary, replace the air cleaner element.
(b) Clean the element with compressed air. First blow from the inside thoroughly, then blow off the
outside of the element.
3. REPLACE AIR FILTER
Replace the air cleaner element with a new one.
4. REPLACE SPARK PLUGS (See page IG−1 )
5. REPLACE ENGINE OIL AND OIL FILTER (See page LU−2)
6. REPLACE ENGINE COOLANT (See page CO−2)
7. INSPECT CHARCOAL CANISTER (See page EC−6 )
8. REPLACE GASKET IN FUEL TANK CAP (See page
EC−6)
9. INSPECT FUEL LINES AND CONNECTIONS (See page EC−6)
10. INSPECT EXHAUST PIPES AND MOUNTINGS
Visually inspect the p ipes, hangers and connections for severe
corrosion, leaks or damage.
11. ADJUST VALVE CLEARANCE (See page EM−4)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

MA04V−01
P22573
−
MAINTENANCE CHASSIS
MA−7
47
Author: Date:
1996 LAND CRUISER (RM451U)
CHASSIS
INSPECTION
1. INSPECT STEERING LINKAGE
(a) Check the steering linkage for looseness or damage.
Check that the tie rod ends do not have excessive
play.
Check that the boot clamps are not loose.
(b) Inspect the dust cover for damage.
2. INSPECT SRS AIRBAG (Driver airbag: See page RS−9 )
(Front passenger airbag: See page RS−23 )
3. INSPECT STEERING GEAR HOUSING OIL
Check the steering gear housing for oil leakage.
If leakage is found, check for cause and repair.
4. INSPECT OIL LEVEL IN AUTOMATIC TRANSMISSION
(See page DI−131 )
5. INSPECT OIL LEVEL IN TRANSFER AND DIFFEREN- TIAL
(a) Transfer: Remove the filler plug and feel inside the hole with your
finger. Check that the oil comes to within 5 mm (0.20 in.)
of the bottom edge of the hole.
If the level is low, add oil until it begins to run out of the filler hole.
Oil drade: API GL −4 or GL−5
Viscosity: 75W−90
(b) Differential: Remove the filler plug and feel inside the hole with your
finger. Check that the oil comes to within 5 mm (0.20 in.)
of the bottom edge of the hole.
If the level is low, add oil until it begins to run out of the filler hole.
Oil drade: Hypoid gear oil API GL −5
Viscosity:
Above −18°C (0° F) SAE 90
Below −18°C (0° F) SAE 80W−90 or 80W
6. REPLACE AUTOMATIC TRANSMISSION FLUID (See page DI−3)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

MA04W−01
−
MAINTENANCE BODY
MA−9
49
Author: Date:
1996 LAND CRUISER (RM451U)
BODY
INSPECTION
1. TIGHTEN BOLTS AND NUTS ON CHASSIS AND BODY
(a) Tighten the front seat−to−body mounting bolts. Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
(b) Under Severe Conditions: In addition to the above maintenance items, check for
loose or missing nuts and bolts on the steering system,
drive train, suspension system, fuel tank mounts, engine
mounts, etc.
2. FINAL INSPECTION
(a) Check the operation of the body parts:
Hood:
Auxiliary catch operates properly
Hood locks securely when closed
Front and rear doors:
Door locks operate properly
Doors close properly
Back door:
Door lock operates properly
Seats:
Seat adjusts easily and locks securely in any posi-
tion
Front seat back locks securely in any position
Folding −down rear seat backs look securely
(b) Road test
Check the engine and chassis for abnormal noises.
Check that the vehicle does not wander or pull to
one side.
Check that the brakes work properly and do not
drag.
(c) Be sure to deliver a clean car. Especially check the steering wheel, shift lever knob, all
switch knobs, door handles and seats.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP3KT−01
−
PREPARATION AUTOMATIC TRANSMISSION
PP−29
78
Author: Date:
1996 LAND CRUISER (RM451U)
AUTOMATIC TRANSMISSION
SST (Special Service Tools)
09032−00100Oil Pan Seal Cutter
09201−10000Valve Guide Bushing Remover &
Replacer SetSpeedometer driven gear oil seal
(09201−01080)Valve Guide Bushing Remover &
Replacer 8
09350−30020TOYOTA Automatic Transmission
Tool Set
(09351−32010)One−way Clutch Test Tool
(09351−32020)Stator Stopper
09921−00010Spring Tension ToolSpeedometer driven gear oil seal
09992−00095Automatic Transmission Oil
Pressure Gauge Set
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP2XS−01
−
PREPARATION AUTOMATIC TRANSMISSION
PP−31
1996 LAND CRUISER (RM451U)
EQUIPMENT
Dial indicator with magnetic baseCheck drive plate runout
OBD II scan tool
Straight edgeTorque converter clutch
Torque wrench
Vernier CalipersTorque converter clutch
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
PREPARATION SUSPENSION AND AXLE
PP−43
92
Author: Date:
1996 LAND CRUISER (RM451U)
09504−00011Differential Side Bearing
Adjusting Nut WrenchFront differential
Rear differential
09504−22011Differential Side Bearing
ReplacerRear differential
09506−35010Differential Drive Pinion Rear
Bearing ReplacerRear differential
Rear suspension
09509−25011Rear Axle Bearing Lock Nut
WrenchRear axle
09517−36010Rear Axle Shaft Oil Seal
Replacer −Rear axle
09550−10013Replacer Set ”B”Rear differential
Rear suspension
(09553−10010)Differential Side Bearing
Replacer
(09557−10011)Differential Drive Pinion
Front Bearing Replacer
09550−60010Differential Side Bearing
ReplacerRear differential
09556−22010Drive Pinion Front Bearing
RemoverFront differential
Rear differential
09605−60010Steering Knuckle Bearing Cup
Replacer−Front axle
09606−60020Steering Knuckle Bearing RemoverFront axle
09607−60020Front Wheel Adjusting Nut WrenchFront axle
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP−44
−
PREPARATION SUSPENSION AND AXLE
93
Author: Date:
1996 LAND CRUISER (RM451U)
09611−22012Tie Rod End PullerFront axle
09612−65014Steering Worm Bearing PullerFront axle
(09612−01010)Claw ”A”
(09612−01050)Hanger Pin with Nut
09618−60010Front Axle & Drive Shaft Bearing
ReplacerFront axle
09710−22021Front Suspension Bushing Tool
SetRear suspension
(09710−01071)Lower Arm Bushing Remover
09710−22042Rear Suspension Bushing Tool SetFront suspension
(09710−02051)Base
(09710−02061)Replacer
(09710−02071)Bushing Remover & Replacer
09710−30050Suspension Arm Bushing ReplacerFront suspension
09726−40010Lower Control Shaft Bearing
ReplacerFront differential
Rear differential
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PR0058
MatchmarksPR06S−03
Z00753
PR0060
SSTA
PR0061
Z00754
SST
PR−6
−
PROPELLER SHAFT SPIDER BEARING
854
Author: Date:
1996 LAND CRUISER (RM451U)
SPIDER BEARING
REPLACEMENT
NOTICE:
Be careful not to grip the propeller shaft tube too tightly in
the vise as this will cause deformation.
1. REMOVE PROPELLER SHAFT (See page PR−3)
2. PLACE MATCHMARKS ON SHAFT AND YOKE
3. REMOVE SNAP RINGS
(a) Using a brass bar and hammer, slightly tap in the bearing
outer races.
(b) Using 2 screwdrivers, remove the 4 snap rings from the grooves.
4. REMOVE SPIDER BEARINGS
(a) Using SST, push out the bearing from the flange. SST 09332−25010
HINT:
Sufficiently raise the part indicated by A so that it does not come
into contact with the bearing.
(b) Clamp the bearing outer race in a vise and tap off the flange with a hammer.
HINT:
Remove the bearing on the opposite side by the same proce-
dure.
(c) Install the 2 removed bearing outer races to the spider.
(d) Using SST, push out the bearing from the yoke. SST 09332−25010
(e) Clamp the outer bearing race in a vise and tap off the yoke
with a hammer.
HINT:
Remove the bearing on the opposite side in the same proce-
dure.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010