1996 TOYOTA LAND CRUISER Front disc

N06513
AC3JP−01
Z09802
Connector ”A”Connector ”B”
1 2
1
2
3
AC−58
−
AIR CONDITIONING REAR BLOWER RESISTOR
1385
Author: Date:
1996 LAND CRUISER (RM451U)
REAR BLOWER RESISTOR
INSPECTION
1. REMOVE FRONT SEAT RH
2. REMOVE BLOWER RESISTOR
(a) Disconnect the connector.
(b) Remove the 2 screws and blower resistor.
3. INSPECT REAR BLOWER RESISTOR CONTINUITY
ConditionTester connectionSpecified condition
ConstantA1 − B1
A2 − A3 − B2Continuity
If continuity is not as specified, replace the blower resistor.
4. REINSTALL REAR BLOWER RESISTOR
H-3-2 H-2-2
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT−22
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
1996 LAND CRUISER (RM451U)
(i) Remove the 4 bolts and transfer shift lever.
Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
(j) Remove the 2 cushions.
6. DISCONNECT THESE CONNECTORS:
No.1 vehicle speed sensor
No.2 vehicle speed sensor
Park/neutral position switch
Solenoid connector
ATF temperature sensor
Center differential lock indicator switch
L4 position switch
Neutral position switch
7. DISCONNECT BLEEDER HOSE FROM TRANSFER
8. REMOVE FRONT AND REAR PROPELLER SHAFT (See page PR−3 )
9. REMOVE OIL FILLER PIPE
(a) Remove the level gauge.
(b) Remove the upper side mounting bolt.
(c) Remove the bolt and filler pipe.
HINT:
At the time of installation, replace the used O −ring with a new
one.
10. LOOSEN 2 OIL COOLER PIPE UNION NUTS
Torque: 34 N·m (350 kgf·cm, 25 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
AT−23
1996 LAND CRUISER (RM451U)
11. REMOVE 4 STABILIZER BAR BRACKET MOUNTING
BOLTS
Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
12. REMOVE ENGINE UNDER COVER
Remove the 4 bolts and engine under cover. Torque: 28 N·m (290 kgf·cm, 21 ft·lbf)
13. REMOVE TORQUE CONVERTER CLUTCH MOUNT- ING BOLT
(a) Remove the converter hole plug.
(b) Turn the crankshaft to gain access to each bolt.
(c) Hold the crankshaft pulley nut with a wrench and remove the 6 bolts.
Torque: 55 N·m (550 kgf·cm, 40 ft·lbf)
HINT:
At the time of installation, first install gray colored bolt and then
5 other bolts.
14. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(a) Remove the 2 nuts, bolts and gasket, and disconnect the
front exhaust pipe assembly.
Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
HINT:
At the time of inatallation, replace the used nuts and gasket with
new nuts and gasket.
(b) Loosen the clamp bolt and disconnect the clamp from the
No.1 support bracket.
Torque: 19 N·m (195 kgf·cm, 14 ft·lbf)
(c) Remove the 2 bolts and No.1 support bracket. Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07409
AT−24
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
1996 LAND CRUISER (RM451U)
(d) Remove the 4 nuts and 2 gaskets, shift the front exhaust
pipe assembly to the vehicle’s outside.
Torque: 62 N·m (630 kgf·cm, 46 ft·lbf)
HINT:
At the time of installation, replace the used gaskets and nuts
with new gaskets and nuts.
15. REMOVE STARTER
(a) Remove the nut and disconnect the terminal and connec-
tor.
(b) Remove the lower side mounting bolt and starter. Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
16. REMOVE CROSSMEMBER
(a) Support the transmission with a transmission jack.
(b) Remove the 8 bolts and 2 nuts, and then remove the crossmember.
Torque:
Bolt: 61 N·m (620 kgf·cm, 45 ft·lbf)
Nut: 74 N·m (750 kgf·cm, 54 ft·lbf)
17. REMOVE TRANSMISSION
(a) Lower the rear end of the transmission.
NOTICE:
Be careful not to damage the cooling fan, brake booster
and brake line.
(b) Separate the wire harness from the transmission and transfer.
(c) Remove the oil cooler pipe mounting bolts from the torque
converter clutch housing, and then disconnect the 2 oil
cooler pipes from the elbows.
(d) Remove the 10 bolts and transmission. Torque: 72 N·m (730 kgf·cm, 53 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LS−01
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
BE−1
1139
Author: Date:
1996 LAND CRUISER (RM451U)
BODY ELECTRICAL SYSTEM
PRECAUTION
Take care to observe the following precautions when performing inspections o\
r removal and replacement
of body electrical related parts.
1. HEADLIGHT SYSTEM
Halogen bulbs have pressurized gas inside and require special handling. They ca\
n burst if scratched or
dropped. Hold a bulb only by its plastic or metal case. Don’t touch the glass\
part of a bulb with bare hands.
2. SRS (SUPPLEMENTAL RESTRAINT SYSTEM)
The LAND CRUISER is equipped with an SRS (Supplemental Restraint System) such as the driver airbag
and front passenger airbag. Failure to carry out service operation in th\
e correct sequence could cause the
SRS to unexpectedly deploy during servicing, possibly leading to a serious accident. Before servicing (in\
-
cluding removal or installation of parts, inspection or replacement), be sure t\
o read the precautionary notices
in the RS section.
3. AUDIO SYSTEM
If the negative (−) terminal cable is disconnected from the battery, the preset AM, FM 1 and FM 2 stations
stored in memory are erased, so be sure to note the stations and reset them af\
ter the negative ( −) terminal
cable is reconnected to the battery.
4. MOBILE COMMUNICATION SYSTEM
If the vehicle is equipped with a mobile communication system, refer to \
precautions in the IN section.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M4−01
BE1428
ON
OFF
−
BODY ELECTRICAL INTERIOR LIGHT SYSTEM
BE−21
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT GLOVE BOX LIGHT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF (Closed)−No continuity
ON (Opened)1 − 2Continuity
If continuity is not as specified, replace the switch.
2. INSPECT DOOR COURTESY SWITCH CONTINUITY
(a) Check that there is continuity between terminal and the
switch body with the switch ON (switch pin released:
opened door).
(b) Check that there is no continuity between terminal and the switch body with the switch OFF (switch pin pushed
in: closed door).
If operation is not as specified, replace the switch.
3. INSPECT FRONT PERSONAL LIGHT CONTINUITY
Switch positionTester connectionSpecified condition
OFF−No continuity
ON5 − 6Continuity
If continuity is not as specified, replace the personal light.
4. INSPECT ROOM LIGHT ASSEMBLY
(a) Disconnect the connector from room light assembly.
(b) Turn the room light switch ON, check that there is continu-
ity between terminal 2 and body ground.
(c) Turn the room light switch DOOR, and check that there is continuity between terminal 1 and 2.
If operation is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL WIPER AND WASHER SYSTEM
BE−29
1996 LAND CRUISER (RM451U)
7. INSPECT REAR WIPER RELAY INTERMITTENT OP-
ERATION
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative ( −) lead to terminal 4.
(b) Connect the positive (+) lead from the voltmeter to termi- nal 3 and the negative ( −) lead to terminal 4.
(c) After disconnecting the positive (+) lead from terminal 2,
connect it to terminal 1, and then, check that the meter
needle rises from O V to battery positive voltage within 6
to 10 seconds.
If operation is not as specified, replace the relay.
8. Low Speed: INSPECT FRONT WIPER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 3 and
negative ( −) lead to terminal 1, and check that the motor oper-
ates at low speed.
If operation is not as specified, replace the motor.
9. High Speed:
INSPECT FRONT WIPER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 2 and
the negative (− ) lead to terminal 1, and check that the motor op-
erates at high speed.
If operation is not as specified, replace the motor.
10. Stopping at Stop Position: INSPECT FRONT WIPER MOTOR OPERATION
(a) Operate the motor at low speed and stop the motor opera-
tion anywhere except at the stop position by disconnect-
ing positive (+) lead from terminal 3.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO382−01
BO−28
−
BODY FRONT WIPER AND WASHER
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE WIPER ARMS
2. REMOVE COWL LOUVER
3. REMOVE WIPER MOTOR AND WIPER LINK
(a) Disconnect the connector, then unfasten 4 bolts and wip-
er motor.
(b) Remove the wiper link.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010