1996 TOYOTA LAND CRUISER Front disc

SA1948
21
4
Z07264
Ohmmeter
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
SA−105
962
Author: Date:
1996 LAND CRUISER (RM451U)
4. INSPECT DIFF. LOCK CONTROL SWITCH
Inspect the switch continuity between terminals, as shown.
Switch PositionTerminalsSpecified Condition
OFF1 − 2No continuity
1 − 4No continuity
RR1 − 2No continuity
1 − 4Continuity
FR RR1 − 2Continuity
1 − 4Continuity
If continuity is not as specified, replace the switch.
5. INSPECT DIFF. LOCK POSITION SWITCH
(a) Front and Rear:
Inspect the diff. lock position switch.
(1) Check that there is continuity between terminalswhen the switch is pushed (differential connected
position).
(2) Check that there is no continuity when the switch is
free (differential disconnected position).
If operation is not as specified, replace the switch.
(b) Inspect the center diff. indicator switch.
6. INSPECT VEHICLE SPEED SENSOR AND INDICATOR
LIGHT
(a) Inspect the vehicle speed sensor (See page BE−34).
(b) Inspect the indicator light.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VN−02
Z07258
Z07261
SA2619
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
SA−107
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE FRONT ACTUATOR
(a) Shifting the front differential lock.
(b) Disconnect the connector and tube.
(c) Remove the 2 nuts, bolt and actuator.
(d) Remove the O−ring from the actuator.
2. REMOVE REAR ACTUATOR
(a) Shifting the gear differential lock.
(b) Remove the actuator protector.
Remove the 2 nuts, bolt and protector.
(c) Disconnect the connectors and tube.
(d) Remove the rear Diff. lock position switch.
(e) Remove the cover. (1) Remove the 3 bolts.
(2) Using a brass bar and hammer, remove the cover.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SR16A−03
−
STEERING TILT STEERING COLUMN
SR−11
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE STEERING WHEEL PAD
NOTICE:
If the airbag connector is disconnected with the ignition
switch at ON or ACC, DTCs will be recorded. Never use air-
bag parts from another vehicle. When replacing parts, re-
place with new parts.
(a) Place the front wheels facing straight ahead.
(b) Remove the steering wheel lower No.2 and No.3 cover from the steering wheel.
(c) Using a torx socket wrench, loosen the 2 torx screws.
HINT:
Loosen the 2 screws until the groove along the screw circumfer-
ence catches on the screw case.
(d) Pull out the wheel pad from the steering wheel and dis- connect the airbag connector.
CAUTION:
When storing the wheel pad, keep the upper surface of the
pad facing upward. Never disassemble the wheel pad.
NOTICE:
When removing the wheel pad, take care not to pull the air-
bag wire harness.
2. REMOVE STEERING WHEEL
(a) Disconnect the connector.
(b) Remove the steering wheel set nut.
(c) Place matchmarks on the steering wheel and main shaft assembly.
(d) Using SST, remove the wheel. SST 09950 −50010 (09951 −05010, 09952 −05010,
09953 −05020, 09954 −05020)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SR16M−01
−
STEERING POWER STEERING GEAR
SR−35
1996 LAND CRUISER (RM451U)
REMOVAL
1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD
2. REMOVE STEERING WHEEL PAD (See page SR−11)
3. REMOVE STEERING WHEEL (See page SR−11)
4. REMOVE FRAME SEAL
5. REMOVE LINK JOINT PROTECTOR
Remove the 2 bolts.
6. DISCONNECT PITMAN ARM WITH RELAY ROD
(a) Remove the pitman arm set nut and spring washer.
(b) Using SST, disconnect the pitman arm from the gear as- sembly.
SST 09628−62011
7. DISCONNECT PRESSURE FEED AND RETURN TUBES
Using SST, disconnect the pressure feed and return tubes. SST 09631−22020
8. DISCONNECT SLIDING YOKE SUB−ASSEMBLY
(See page SR−13 )
9. REMOVE PS GEAR ASSEMBLY
Remove the 4 installation bolts and nuts.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1ED−02
−
SERVICE SPECIFICATIONS SUSPENSION AND AXLE
SS−33
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
FRONT
Axle hub x Disc6465047
Axle hub bearing lock nut6465047
Flange x Axle hub3536026
Brake caliper x Axle carrier1231,25090
Brake caliper x Flexible hose3031022
Steering knuckle x Knuckle arm9698071
Bearing cap x Steering knuckle9698071
Knuckle arm x Tie rod9192567
Steering knuckle x Knuckle spindle4747534
Oil seal end retainer x Knuckle arm5.45548 in.·lbf
ABS speed sensor set bolt x Steering knuckle1818513
Hub nut Steel wheel
Aluminum wheel147
1031,500
1,050109 76
Drain plug4950036
Filler plug4950036
Propeller shaft x Companion flange8890065
Side bearing cap x Differential carrier7880058
Ring gear x Differential case9798571
Drive pinion x Companion flange196 − 3432,000 − 3,500145 − 253
Differential LH case x RH case4748035
Differential lock shift retainer2424017
Differential lock screw plug2222016
Differential lock indicator switch4041030
Differential lock actuator2627020
Differential carrier x Axle housing2728020
Adjusting nut lock x Bearing cap131309
Follow spring x Frame9.29482 in.·lbf
Stabilizer bar x Axle housing2526019
Shock absorber x Axle housing6970051
Shock absorber x Frame6970051
Stabilizer bar link x Cover1818513
Stabilizer bar link x Link bracket1031,05076
Lateral control rod x Frame1711,750127
Lateral control rod x Axle housing1711,750127
Leading arm x Frame1771,800130
Leading arm x Axle housing1711,750127
REAR
Rear axle shaft x Axle hub3434025
Rear axle bearing lock nut5960043
Rear axle bearing lock nut screw5.45548 in.·lbf
Brke caliper x Axle carrier1031,05076
ABS speed sensor set bolt1818513
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EE−02
−
SERVICE SPECIFICATIONS BRAKE
SS−35
158
Author: Date:
1996 LAND CRUISER (RM451U)
BRAKE
SERVICE DATA
Brake pedal height from asphalt sheet167.5 − 177.5 mm (6.59 − 6.99 in.)
Brake pedal freeplay3 − 6 mm (0.12 − 0.24 in.)
Brake pedal reserve distance at 490 N (50 kgf, 110.2 lbf)More than 68 mm (2.68 in.)
Brake booster push rod to piston clearance w/ SST0 mm (0 in.)
Front brake pad thickness STD
Minimum9.5 mm (0.374 in.)
1.0 mm (0.039 in.)
Front brake disc thickness STD
Minimum32.0 mm (1.260 in.)
30.0 mm (1.181 in.)
Front brake disc runout Maximum0.15 mm (0.0059 in.)
Rear brake pad thickness STD
Minimum10.0 mm (0.394 in.)
1.0 mm (0.039 in.)
Rear brake disc thickness STD
Minimum18.0 mm (0.709 in.)
16.0 mm (0.630 in.)
Rear brake disc runout Maximum0.15 mm (0.0059 in.)
Rear brake disc inside diameter STD
Maximum230 mm (9.06 in.)
231 mm (9.09 in.)
Parking brake shoe lining thickness STD
Minimum4.0 mm (0.157 in.)
1.0 mm (0.039 in.)
Parking brake lever travel at 196 N (20 kgf, 44.1 lbf)7 − 9 clicks
Parking brake clearance between rear shoe and leverLess than 0.35 mm (0.0138 in.)
Parking brake shoe and lever clearance adjusting shim thickness0.3 mm (0.012 in.)
0.6 mm (0.024 in.)
0.9 mm (0.035 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EF−02
SS−36
−
SERVICE SPECIFICATIONS BRAKE
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Master cylinder x Piston stopper bolt101007
Master cylinder x Reservoir1.717.515.2 in.·lbf
Master cylinder x Brake booster131309
Brake line union nut1515511
Brake booster clevis lock nut2526019
Brake booster x Pedal bracket131309
Bleeder plug1111 08
Front disc brake caliper installation bolt1231,25090
Front disc brake caliper x Flexible hose3031022
Parking brake bellcrank x Backing plate131309
Rear disc brake cliper x Spindle pin8890065
Rear disc brake caliper x Flexible hose3031022
Rear disc brake torque plate x Knuckle1031,05076
LSP & BV bracket x Frame2526019
LSP & BV x LSP & BV bracket131309
LSP & BV spring x LSP & BV bracket1818513
LSP & BV spring x Shackle No. 11818513
LSP & BV shackle lock nut2525018
LSP & BV shackle x Shackle bracket131309
LSP & BV shackle bracket x Rear axle housing1919514
ABS actuator assembly x Body1919514
ABS actuator x Actuator bracket5.45548 in.·lbf
ABS control relay x Actuator bracket131309
Front speed sensor installation bolt1818513
Rear speed sensor installation bolt1818513
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010