1996 TOYOTA LAND CRUISER oil

P22687
P08512
IG−2
−
IGNITION IGNITION SYSTEM
736
Author: Date:
1996 LAND CRUISER (RM451U)
2. REMOVE NO.2 PCV HOSE
3. REMOVE AIR CLEANER HOSE
4. DISCONNECT THROTTLE CABLE
5. REMOVE NO.2 AND NO.3 CYLINDER HEAD COVERS
Remove the 4 bolts and head covers.
6. DISCONNECT HIGH −TENSION CORDS FROM SPARK
PLUGS
(a) Remove the 2 mounting bolts of the No.1 and No.2 cord clamps.
(b) Disconnect the high −tension cords at the rubber boot.
Do not pull on the cords.
NOTICE:
Pulling on or bending the cords may damage the conductor
inside.
7. DISCONNECT HIGH−TENSION CORDS FROM DIS- TRIBUTOR CAP AND IGNITION COIL
(a) Using a screwdriver, lift up the lock claw and disconnect
the holder from the distributor cap (ignition coil).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
IGNITION IGNITION SYSTEM
IG−3
737
Author: Date:
1996 LAND CRUISER (RM451U)
(b) Disconnect the high−tension cord at the grommet.
Do not pull on the cord.
NOTICE:
Pulling on or bending the cords may damage the conductor
inside.Do not wipe any of the oil from the grommet after the
high −tension cord is disconnected.
8. INSPECT HIGH−TENSION CORD RESISTANCE
Using an ohmmeter, measure the resistance. Maximum resistance: 25 k Ω per cord
If the resistance is greater than maximum, check the terminals.
If necessary, replace the high −tension cord.
9. RECONNECT HIGH− TENSION CORDS TO DISTRIBU-
TOR CAP AND IGNITION COIL
(a) Assemble the holder and grommet.
HINT:
Connect the high− tension cords to the distributor cap as shown
in the illustration.
(b) Align the spline of the distributor (ignition coil) with the spline of the holder, and push in the cord.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P03792
IG−6
−
IGNITION IGNITION SYSTEM
740
Author: Date:
1996 LAND CRUISER (RM451U)
19. ADJUST ELECTRODE GAP
Carefully bend the outer electrode to obtain the correct elec-
trode gap.
Correct electrode gap: 0.8 mm (0.031 in.)
20. INSTALL SPARK PLUGS
Using a 16 mm plug wrench, install the spark plug. Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
21. RECONNECT HIGH −TENSION CORDS TO SPARK
PLUGS
NOTICE:
”Cold” and ”Hot” in the following sentences express the
temperature of the coils themselves. ”Cold” is from −10° C
(14 °F) to 50° C (122°F) and ”Hot” is from 50 °C (122° F) to
100 °C (212 °F).
22. DISCONNECT IGNITION COIL CONNECTOR
23. DISCONNECT HIGH−TENSION CORD
24. INSPECT PRIMARY COIL RESISTANCE
Using an ohmmeter, measure the resistance between the posi-
tive (+) and negative (−) terminals. Primary coil resistance:
Cold: 0.36 − 0.55 Ω
Hot: 0.45 − 0.65 Ω
If the resistance is not as specified, replace the ignition coil.
25. INSPECT SECONDARY COIL RESISTANCE
Using an ohmmeter, measure the resistance between the posi-
tive (+) and high −tension terminals.
Secondary coil resistance:
Cold: 9.0 − 15.4 kΩ
Hot: 11.4 − 18.1 kΩ
If the resistance is not as specified, replace the ignition coil.
26. RECONNECT HIGH−TENSION CORD
27. RECONNECT IGNITION COIL CONNECTOR
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
IGNITION IGNITION SYSTEM
IG−7
741
Author: Date:
1996 LAND CRUISER (RM451U)
NOTICE:
”Cold” and ”Hot” in the following sentences express the
temperature of the coils themselves. ”Cold” is from −10° C
(14 °F) to 50° C (122°F) and ”Hot” is from 50 °C (122° F) to
100 °C (212 °F).
28. DISCONNECT DISTRIBUTOR CONNECTOR
29. REMOVE DISTRIBUTOR CAP WITHOUT DISCON- NECTING HIGH−TENSION CORDS
30. REMOVE ROTOR
31. INSPECT AIR GAPS
Using a thickness gauge, measure the gap between the signal
rotor and the pickup coil projection. Air gap: 0.2 − 0.4 mm (0.008 − 0.016 in.)
If the gap is not as specified, replace the distributor housing.
32. INSPECT SIGNAL GENERATOR (PICKUP COIL) RE- SISTANCE
Using an ohmmeter, check that the resistance of the pickup coil. Pickup coil resistance:
Cold G1 and G
G2 and G
NE and G185 − 275 Ω
185 − 275 Ω
185 − 275 Ω
Hot G1 and G
G2 and G
NE and G240 − 325 Ω
240 − 325 Ω
240 − 325 Ω
If the resistance is not as specified, replace the distributor hous-
ing.
33. REINSTALL ROTOR
34. REINSTALL DISTRIBUTOR CAP
35. RECONNECT DISTRIBUTOR CONNECTOR
NOTICE:
”Cold” and ”Hot” in the following sentences express the
temperature of the sensor itself.
”Cold” is from −10° C (14°F) to 50° C (122°F) and ”Hot” is
from 50° C (122°F) to 100° C (212°F).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IG0IE−01
−
IGNITION DISTRIBUTOR
IG−11
1996 LAND CRUISER (RM451U)
INSTALLATION
1. CHECK NO.1 CYLINDER TO TDC/COMPRESSION
If necessary, remove the cylinder head cover, and check these
conditions:
Turn the crankshaft pulley and align its groove with
the timing mark ”0” of the timing chain cover.
Verify that the timing marks with 1 and 2 dots are in
straight line on the cylinder head surface as shown
in the illustration.
If not, turn the crankshaft 1 revolution (360°) and align the mark
as above.
2. INSTALL DISTRIBUTOR
(a) Install a new O−ring to the distributor.
HINT:
Always use a new O −ring when installing the distributor.
(b) Align the groove of the distributor housing with the protru-
sion on the driven gear.
(c) Apply a light coat of engine oil on the O −ring.
(d) Insert the distributor, aligning the center of the flange with
that of the bolt hole on the cylinder head.
(e) Lightly tighten the hold −down bolt.
3. INSTALL DISTRIBUTOR CAP
4. CONNECT DISTRIBUTOR CONNECTOR
5. CHECK IGNITION TIMING (See page EM−10)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

LU0817
LU08N−03
EM1759
P22601
Oil Pressure Gauge
P08343
Adhesive
−
LUBRICATION OIL AND FILTER
LU−1
712
Author: Date:
1996 LAND CRUISER (RM451U)
OIL AND FILTER
INSPECTION
1. CHECK ENGINE OIL QUALITY
Check the oil for deterioration, entry of water, discoloring or thin-
ning.
If the quality is visibly poor, replace the oil.
Oil grade:
API grade SH Energy−Conserving II multigrade en-
gine oil or ILSAC multigrade engine oil.
Recommended viscosity is as shown in the illustra-
tion, with SAE 5W −30 being the preferred engine oil.
2. CHECK ENGINE OIL LEVEL
The oil level should be between the ”L” and ”F” marks on the di\
p-
stick.
If low, check for leakage and add oil up to ”F” mark.
3. REMOVE OIL PRESSURE SWITCH, AND INSTALL OIL
PRESSURE GAUGE
4. WARM UP ENGINE
Allow the engine to warm up to normal operating temperature.
5. CHECK OIL PRESSURE Oil pressure:
At idle
29 kPa (0.3 kgf/cm
2, 4.3 psi) or more
At 3,000 rpm
245 − 490 kPa (2.5 − 5.0 kgf/cm
2, 36 − 71 psi)
6. REMOVE OIL PRESSURE GAUGE AND REINSTALL OIL PRESSURE SWITCH
(a) Remove the oil pressure gauge.
(b) Apply adhesive to 2 or 3 threads of the oil pressure switch.
Adhesive:
Part No. 08833 −00080, THREE BOND 1344,
LOCTITE 242 or equivalent
(c) Reinstall the oil pressure switch.
7. START ENGINE AND CHECK FOR LEAKS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

LU0KE−03
LU−2
−
LUBRICATION OIL AND FILTER
1996 LAND CRUISER (RM451U)
REPLACEMENT
CAUTION:
Prolonged and repeated contact with mineral oil will result
in the removal of natural fats from the skin, leading to dry-
ness, irritation and dermatitis. In addition, used engine oil
contains potentially harmful contaminants which may
cause skin cancer.Care should be taken, therefore, when
changing engine oil to minimize the frequency and length
of time your skin is exposed to used engine oil. Protective
clothing and gloves that cannot be penetrated by oil should
be worn. The skin should be thoroughly washed with soap
and water, or use water−less hand cleaner, to remove any
used engine oil. Do not used gasoline, thinners, or sol-
vents.In order to preserve the environment, used oil and
used oil filters must be disposed of only at designated dis-
posal sites.
1. DRAIN ENGINE OIL
(a) Remove the oil filler cap.
(b) Remove the oil drain plug, and drain the oil into a contain-
er.
2. REPLACE OIL FILTER
(a) Using SST, remove the oil filter. SST 09228−44011
(b) Check and clean the oil filter installation surface.
(c) Apply clean engine oil to the gasket of a new oil filter.
(d) Lightly screw the oil filter into place, and tighten it until the
gasket contacts the seat.
(e) Using SST, tighten it an additional 3/4 turn. SST 09228−44011
3. FILL WITH ENGINE OIL
(a) Clean and install the oil drain plug with a new gasket.
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(b) Fill with new engine oil. Oil grade:
See step 1 in oil pressure check
Capacity:
Drain and refill
w/ Oil filter change
7.2 liters (7.5 US qts, 6.3 lmp. qts)
w/o Oil filter change
6.9 liters (7.3 US qts, 6.1 lmp. qts)
Dry fill
8.0 liters (8.5 US qts, 7.0 lmp. qts)
(c) Reinstall the oil filler cap.
4. START ENGINE AND CHECK FOR LEAKS
5. RECHECK ENGINE OIL LEVEL
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

LU0KF−04
−
LUBRICATION OIL PUMP
LU−3
714
Author: Date:
1996 LAND CRUISER (RM451U)
OIL PUMP
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010