1996 TOYOTA LAND CRUISER distributor

IN−34
−
INTRODUCTION TERMS
34
Author: Date:
1996 LAND CRUISER (RM451U)
CW
Curb W
eight
DCDirect Current
DEFDefogger
DFLDeflector
DIFF.Differential
DIFF. LOCKDifferential Lock
D/INJDirect Injection
DLIDistributorless Ignition
DOHCDouble Over Head Cam
DPDash Pot
DSDead Soak
DSPDigital Signal Processor
EBDElectronic Brake Force Distribution
ECAMEngine Control And Measurement System
ECDElectronic Controlled Diesel
ECDYEddy Current Dynamometer
ECUElectronic Control Unit
EDElectro−Deposited Coating
EDICElectric Diesel Injection Control
EDUElectronic Driving Unit
EFIElectronic Fuel Injection
E/GEngine
EGR−VMExhaust Gas Recirculation −Vacuum Modulator
ELREmergency Locking Retractor
ENGEngine
ESAElectronic Spark Advance
ETCSElectronic Throttle Control System
EVPEvaporator
E−VRVElectric V acuum Regulating V alve
EXHExhaust
FEFuel Economy
FFFront−Engine Front− Wheel−Drive
F/GFuel Gage
FIPGFormed In Place Gasket
FLFusible Link
F/PFuel Pump
FPUFuel Pressure Up
FrFront
FRFront−Engine Rear− Wheel−Drive
F/WFlywheel
FW/DFlywheel Damper
FWDFront−Wheel−Drive
GASGasoline
GSAGear Shift Actuator
GNDGround
HACHigh Altitude Compensator
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IN0CI−02
IN−38
−
INTRODUCTION TERMS
1996 LAND CRUISER (RM451U)
GLOSSARY OF SAE AND TOYOTA TERMS
This glossary lists all SAE− J1930 terms and abbreviations used in this manual in compliance with SAE\
rec-
ommendations, as well as their TOYOTA equivalents.
SAE
ABBREVIATIONSSAE TERMSTOYOT A TERMS
( ) −−ABBREVIA TIONS
A/CAir ConditioningAir Conditioner
ACLAir CleanerAir Cleaner, A/CL
AIRSecondary Air InjectionAir Injection (AI)
APAccelerator Pedal−
B+Battery Positive Voltage+B, Battery Voltage
BAROBarometric PressureHAC
CACCharge Air CoolerIntercooler
CARBCarburetorCarburetor
CFIContinuous Fuel Injection−
CKPCrankshaft PositionCrank Angle
CLClosed LoopClosed Loop
CMPCamshaft PositionCam Angle
CPPClutch Pedal Position−
CTOXContinuous T rap Oxidizer−
CTPClosed Throttle PositionLL ON, Idle ON
DFIDirect Fuel Injection (Diesel)Direct Injection (DI)
DIDistributor Ignition−
DLC1
DLC2
DLC3Data Link Connector 1
Data Link Connector 2
Data Link Connector 31: Check Connector
2: Total Diagnosis Comunication Link (TDCL)
3: OBD II Diagnostic Connector
DTCDiagnostic Trouble CodeDiagnostic Code
DTMDiagnostic Test Mode−
ECLEngine Control Level−
ECMEngine Control ModuleEngine ECU (Electronic Control Unit)
ECTEngine Coolant T emperatureCoolant Temperature, Water Temperature (THW)
EEPROMElectrically Erasable Programmable Read Only Memory
Electrically Erasable Programmable Read Only Memory
(EEPROM),
Erasable Programmable Read Only Memory (EPROM)
EFEEarly Fuel EvaporationCold Mixture Heater (CMH), Heat Control Valve (HCV)
EGRExhaust Gas RecirculationExhaust Gas Recirculation (EGR)
EIElectronic IgnitionTOYOTA Distributorless Ignition (TDI)
EMEngine ModificationEngine Modification (EM)
EPROMErasable Programmable Read Only MemoryProgrammable Read Only Memory (PROM)
EVAPEvaporative EmissionEvaporative Emission Control (EVAP)
FCFan Control−
FEEPROMFlash Electrically Erasable Programmable
Read Only Memory−
FEPROMFlash Erasable Programmable Read Only Memory−
FFFlexible Fuel−
FPFuel PumpFuel Pump
GENGeneratorAlternator
GNDGroundGround (GND)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

S06273
E1
1
G−
2
BR
L
L G1
NE2
NE2−
12
E6
3
2
Distributor
Crankshaft Position Sensor G2
ECM
NE
4
1 L
L
G W
R
E6
E6
E6
E6
E6 11
10 4
56
DI−62
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
DTC P0335 Crankshaft Position Sensor ”A” Circuit Malfunction
CIRCUIT DESCRIPTION
The crankshaft position sensor (NE signal) consists of a signal plate and pick up coil. The NE\
signal plate
has 24 teeth and is built into the distributor. When the camshaft rotates, the protrusion on the signal plate
and the air gap on the pick up coil change, causing fluctuations in the magnetic field and generating an elec-
tromotive force in the pick up coil. The NE signal sensor generates 24 signals fo\
r every engine revolution.
The ECM detects the standard crankshaft angle based on the G1, G2 signals, \
detects the actual crankshaft
angle and the engine speed by the NE signals, and detects misfire by NE2 sign\
als.
DTC No.DTC Detecting ConditionTrouble Area
P0335
No crankshaft position sensor signal (NE signal) to ECM dur-
ing cranking.
(2 trip detection logic) Open or short in crankshaft position sensor circuit for NE
signal.
 Crankshaft position sensor for NE signal
 Starter
 ECM
No crankshaft position sensor signal (NE signal) to ECM with
engine speed 550 rpm or more (2 trip detection logic)
WIRING DIAGRAM
DI5PH−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P24663
1
23
4
(−) (+)
P23505
G, NE signal waveforms
20 m sec/Division (Idling) 5V/DIV
G1
G2
NE
NE2
−
DIAGNOSTICS ENGINE
DI−63
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check resistance of crankshaft position sensor for NE signal.
PREPARATION:
Remove the distributor cap and disconnect distributor connec-
tor.
CHECK:
Measure resistance between terminals 1 and 4 of distributor
connector.
OK:
Resistance
Cold185 − 275 Ω
Hot240 − 325 Ω
”Cold” is from − 10°C (14F° ) to 50°C (122°F) of engine coolant
temperature sensor and ”Hot” is from 50 °C (122° F) to 100° C
(212 °F).
Reference: INSPECTION USING OSCILLOSCOPE
During cranking or idling, check between terminals G1, G2, NE,
NE2 and G− of ECM.
HINT:
The correct waveforms are as shown.
NG Replace distributor housing assembly.
OK
2 Check for open and short in harness and connector between ECM and crank-\
shaft position sensor for NE signal (See page IN−28).
NG Repair or replace harness or connector.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−64
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
3 Check air gap (See page IG−1 ).
NG Replace distributor housing assembly.
OK
Check and replace ECM (See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P24663
2(−)
3
4 1
(+)
−
DIAGNOSTICS ENGINE
DI−65
1996 LAND CRUISER (RM451U)
DTC P0340 Camshaft Position Sensor Circuit
Malfunction
CIRCUIT DESCRIPTION
The camshaft position sensors (G1 and G2 signals) consist of a signal pla\
te and a pick up coil. The G1, G2,
signal plates each have one tooth on the outer circumference and are built int\
o the distributor. When the
camshaft rotates, the protrusion on the signal plate and the air gap on the pick \
up coil change, causing fluc-
tuations in the magnetic field and generating an electromotive force in the pick \
up coil. The ECM detects the
standard crankshaft angle based on the G1, G2 signals, detects the actual cranks\
haft angle and engine
speed by the NE signals, and detects misfire by NE2 signals.
DTC No.DTC Detecting ConditionTrouble Area
P0340No camshaft position sensor signal (G signal) to ECM with
engine speed 550 rpm or more. Open or short in camshaft position sensor circuit
 Camshaft position sensor
 ECM
WIRING DIAGRAM
Refer to DTC P0335 (Crankshaft Position Sensor ”A” Circuit Malfunction) o\
n page DI−62 for the WIRING
DIAGRAM.
INSPECTION PROCEDURE
1 Check resistance of camshaft position sensor.
PREPARATION:
Disconnect camshaft position sensor connector.
CHECK:
Measure resistance between terminals 2, 3 and 4 of distributor
connector.
OK:
Resistance
Cold185 − 275 Ω
Hot240 − 325 Ω
”Cold” is from − 10°C (14°F) to 50°C (122°F) of engine coolant
temperature and "Hot" is from 50°C (122°F) to 100°C (212°\
F).
Reference: INSPECTION USING OSCILLOSCOPE
Refer to page DI−62 for Reference INSPECTION USING OS-
CILLOSCOPE.
NG Replace distributor housing assembly.
OK
DI5PI−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−66
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
2 Check for open and short in harness and connector between ECM and camshaft
position sensor (See page IN−28).
NG Repair or replace harness or connector.
OK
3 Check air gap (See page IG−1 ).
NG Replace distributor housing assembly.
OK
Check and replace ECM (See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22475
BatteryFusible
Link
FL AM2
F7W−R
EA2
W−R
B−R B−R
EA2
B−R
B−W B−W
W−B
Distributor
Ignition
Coil 4
12
EA2
IH1
W−B
8 1
2
Noise
Filter 45
B 3
Igniter Tr2
2
1
IH2 IH2
B−G
B−G
B−Y B−YE4
E4 IGT
IGF Tr15V
ECM
1 3 11
6
IG Switch
1
EC
17 23
14 13
−
DIAGNOSTICS ENGINE
DI−97
1996 LAND CRUISER (RM451U)
DTC P1300 Igniter Circuit Malfunction
CIRCUIT DESCRIPTION
The ECM determines the ignition timing, turns on Tr1 at a predetermined angle ( °CA) before the desired
ignition timing and outputs and ignition signal (IGT) ”1” to the\
igniter.
Since the width of the IGT signal is constant, the dwell angle control circuit in \
the igniter determines the time
the control circuit starts primary current flow to the ignition coil based \
on the engine rpm and ignition timing
one revolution ago, that is, the time the Tr2 turns on.
When it reaches the ignition timing, the ECM turns Tr1 off and outputs the IGT signal ”O”.
This turns Tr2 off, interrupting the primary current flow and generating a high voltage i\
n the secondary coil
which causes the spark plug to spark. Also, by the counter electromotive forc\
e generated when the primary
current is interrupted, the igniter sends an ignition confirmation signal (IGF)\
to the ECM. The ECM stops fuel
injection as a fail safe function when the IGF signal is not input to the ECM.
DTC No.DTC Detecting ConditionTrouble Area
P1300No IGF signal to ECM for 6 consecutive IGT signals during
engine running Open or short in IGF or IGT circuit from igniter to ECM
 Igniter
 ECM
WIRING DIAGRAM
DI5PQ−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010