1996 TOYOTA LAND CRUISER Preload

BR1CX−03
BR0251
−
BRAKE FRONT BRAKE CALIPER
BR−27
1996 LAND CRUISER (RM451U)
INSPECTION
1. MEASURE PAD LINING THICKNESS
Using a ruler, measure the pad lining thickness.
Standard thickness: 9.5 mm (0.374 in.)
Minimum thickness: 1.0 mm (0.039 in.)
Replace the pad if the thickness is less than the minimum (the
1.0 mm slit is no longer visible), or if it shows signs of uneven
wear.
2. MEASURE DISC THICKNESS
Using a micrometer, measure the disc thickness. Standard thickness: 32.0 mm (1.260 in.)
Minimum thickness: 30.0 mm (1.181 in.)
If the disc is scored or worn, or if its thickness is less than the
minimum, repair or replace the disc.
3. MEASURE DISC RUNOUT
Using a dial indicator, measure the disc runout at a position 10
mm (0.39 in.) from the outside edge. Maximum disc runout: 0.15 mm (0.0059 in.)
If the runout is greater than the maximum, replace the disc or
grind it on a ”On−Car” brake lathe.
HINT:
Before measuring the runout, confirm that the front hub bearing
play is within the specification.
4. IF NECESSARY, REPLACE DISC
(a) Remove the front axle hub (See page SA−7).
(b) Remove the disc from the axle hub.
(c) Install a new disc and torque the bolts. Torque: 74 N·m (750 kgf·cm, 54 ft·lbf)
(d) Install the axle hub and adjust the front bearing preload (See page SA−9 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UD−01
SA2636
Grease
R04134
SST
−
SUSPENSION AND AXLE FRONT AXLE HUB
SA−9
1996 LAND CRUISER (RM451U)
INSTALLATION
1. PACK BEARINGS WITH MP GREASE
(a) Place MP grease on the palm of your hand.
(b) Pack grease into the bearing until the grease oozes out
from the other side.
(c) Do the same around the bearing circumference.
2. COAT INSIDE OF HUB WITH MP GREASE
3. INSTALL INNER BEARING AND OIL SEAL
(a) Place the inner bearing into the hub.
(b) Using SST, install a new oil seal into the hub. SST 09950−60020 (09951 −00910),
09950 −70010 (09951 −07150)
(c) Coat the oil seal lip with MP grease.
4. INSTALL AXLE HUB WITH DISC TO SPINDLE
(a) Place the axle hub with disc to the spindle.
(b) Install the outer bearing.
(c) Install the thrust washer.
5. ADJUST PRELOAD
(a) Using SST, torque the adjusting nut.
SST 09607−60020
Torque: 59 N·m (600 kgf·cm, 43 ft·lbf)
(b) Turn the hub right and left 2 or 3 times.
(c) Using SST, torque the adjusting nut.
SST 09607−60020
Torque: 59 N·m (600 kgf·cm, 43 ft·lbf)
(d) Loosen the nut until it can be turned by hand.
(e) Using SST, torque the adjusting nut again.
SST 09607−60020
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
NOTICE:
Check that the bearing has no play.
(f) Using a spring tension gauge, measure the preload.
Preload (at starting):
28 − 56 N (2.9 − 5.7 kgf, 6.4 − 12.6 lbf)
6. INSTALL LOCK WASHER AND LOCK NUT
(a) Install a new lock washer and lock nut.
(b) Using SST, torque the lock nut. SST 09607−60020
Torque: 64 N·m (650 kgf·cm, 47 ft·lbf)
(c) Check that axle hub turns smoothly and that the bearing has no play.
(d) Using a spring tension gauge, check the preload. Preload (at starting):
28−56 N (2.9−5.7 kgf, 6.4−12.6 lbf)
If it is not within the specification, adjust it with the adjusting nut
after removing the lock washer and lock nut.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07149SST
SA−14
−
SUSPENSION AND AXLE STEERING KNUCKLE AND AXLE SHAFT
1996 LAND CRUISER (RM451U)
(d) Using SST, remove the bearing cap and shim from the
steering knuckle.
SST 09606−60020
HINT:
Use the SST without a collar.
In some cases, to satisfy the standard value of preload,
more than one shims are used.
(e) Using SST, remove the knuckle arm and shim from the steering knuckle.
SST 09606−60020
HINT:
Use the SST without a collar.
In some cases, to satisfy the standard value of preload,
more than one shims are used.
9. REMOVE STEERING KNUCKLE AND BEARING
HINT:
Mark the removed adjusting shim and bearings so as to enable
reassembling them to their proper positions.
10. REMOVE OIL SEAL TO AXLE HOUSING
Using SST, remove the oil seal. SST 09308−00010
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R13138
90°
Z15222
Molybdenum
Disulfide
Lithium
Base Grease
NIGI No.2
SA−18
−
SUSPENSION AND AXLE STEERING KNUCKLE AND AXLE SHAFT
1996 LAND CRUISER (RM451U)
(h) Install the 2 plate washers and bolts.
Torque: 96 N·m (980 kgf·cm, 71 ft·lbf)
6. MEASURE BEARINGS PRELOAD
Using a spring tension gauge, measure the preload. Preload (at starting):
25 − 44 N (2.5 − 4.5 kgf, 5.6 − 9.9 lbf)
7. ADJUST BEARING PRELOAD
(a) Remove the bearing cap and knuckle arm (See page SA−13 ).
(b) Select the adjusting shim. Adjusting shim thickness
Thickness mm (in.)Thickness mm (in.)
0.1 (0.004)0.5 (0.020)
0.2 (0.008)1.0 (0.039)
(c) Install the bearing cap and knuckle arm (See page SA−17 ).
8. CONNECT TIE ROD TO KNUCKLE ARM
Torque the nut and secure it with a new cotter pin. Torque: 91 N·m (925 kgf·cm, 67 ft·lbf)
9. INSTALL OIL SEAL END RETAINER TO KNUCKLE ARM
Install the oil seal end retainer to steering knuckle with the 6
bolts. Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
10. INSTALL AXLE SHAFT
Position one flat part of the outer shaft upward and install the
shaft.
11. PACK MOLYBDENUM DISULFIDE LITHIUM BASE GREASE, NLGI NO.2
Pack molybdenum disulfide lithium base grease, NLGI No.2
into the knuckle to about 3 fourths of the knuckle.
12. INSTALL KNUCKLE SPINDLE, DUST COVER WITH
GASKETS AND DUST SEAL
(a) Place a new gasket in the position on the knuckle and
install the spindle.
(b) Place the dust cover, dust seal and a new gasket on the spindle.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1960
SST
RA1072
Filler Hole
Oil
0 − 5 mm (0 − 0.20 in.)
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL REAR OIL SEAL
SA−23
1996 LAND CRUISER (RM451U)
(c) Apply light coat of gear oil on threads of a new companion
flange nut.
(d) Using SST to hold the flange, torque the nut.
SST 09330−00021
Torque: 196 N·m (2,000 kgf·cm, 145 ft·lbf)
14. ADJUST DRIVE PINION PRELOAD (See page SA−36 )
15. STAKE DRIVE PINION NUT
16. INSTALL FRONT PROPELLER SHAFT (See page PR−5 )
17. FILL DIFFERENTIAL WITH GEAR OIL Torque: 49 N·m (500 kgf·cm, 39 ft·lbf)
Oil type: Hypoid gear oil API GL −5
Recommended oil viscosity:
Above −18°C (0° F) SAE 90
Below −18°C (0° F) SAE 80W−90 or 80W
Capacity:
w/o Differential lock:
2.80 liters (2.9 US qts, 2.5 Imp. qts)
w/ Differential lock:
2.65 liters (2.8 US qts, 2.3 Imp. qts)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W00493
30 mm
(1.18 in.)
SA1UN−03
SA2465
SA2462
SA2403
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
SA−29
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. CHECK RUNOUT OF COMPANION FLANGE
Using a dial indicator, measure the vertical and lateral runout of
the companion flange. Maximum runout: 0.10 mm (0.0039 in.)
2. CHECK RING GEAR RUNOUT
Using a dial indicator, measure the ring gear runout. Maximum runout: 0.10 mm (0.0039 in.)
If the runout is greater than the maximum, replace the ring gear
and driven pinion as a set.
3. CHECK RING GEAR BACKLASH
Using a dial indicator, measure the ring gear backlash. Backlash: 0.13 −0.18 mm (0.0051 −0.0071 in.)
If the backlash is not within the specification, adjust the side
bearing preload or repair as necessary.
4. MEASURE DRIVE PINION PRELOAD
Using a torque wrench, measure the preload of backlash be-
tween the drive pinion and ring gear. Preload (at starting):
0.5 − 0.8 N·m (5 − 8 kgf·cm, 4.3 − 6.9 in.·lbf)
5. CHECK TOTAL PRELOAD
Using a torque wrench, measure the preload. Total preload (at starting):
Drive pinion preload plus
0.4 − 0.6 N·m (4 − 6 kgf·cm, 3.5 − 5.2 in.·lbf)
If necessary, disassemble and inspect the differential.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2465
SA2406
SST
SA2203
SSTSST
Front
Rear
FA2042
SST
R13140
SST
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
SA−39
1996 LAND CRUISER (RM451U)
7. CHECK RING GEAR RUNOUT
(a) Install the differential case onto the carrier and tighten the
adjusting nut just to where there is no play in the bearings.
(b) Using a dial indicator, check the ring gear runout. Maximum runout: 0.10 mm (0.0039 in.)
(c) Remove the differential case.
8. INSTALL OIL STORAGE RING
Using SST and a hammer, install a new oil storage ring. SST 09316−60011 (09316 −00011, 09316−00021)
9. INSTALL DRIVE PINION FRONT AND REAR BEARING
OUTER RACES
Front side:
Using SST and a press, install the 2 outer races.
SST 09316−60011 (09316 −00011, 09316−00051)
Rear side:
Using SST and a press, install the 2 outer races.
SST 09316−60011 (09316 −00011, 09316−00021)
10. INSTALL DRIVE PINION FRONT BEARING
(a) Install the plate washer on the drive pinion with the cham-
fered end facing the pinion gear.
(b) Using SST and a press, install the front bearing onto the
drive pinion.
SST 09506−30012
11. TEMPORARILY ADJUST DRIVE PINION PRELOAD
(a) Install the drive pinion, rear bearing and oil slinger.
HINT:
Assemble the spacer and oil seal after adjusting the gear con-
tact pattern.
(b) Install the companion flange with SST. SST 09550 −30010 (09951 −03010, 09953 −03010,
09954 −03010, 09955 −03030, 09956−03020)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2401
SST
SA2403
SA2161
MP Grease
Z10100
SA−40
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
(c) Adjust the drive pinion preload by tightening the compan-
ion flange nut.
Using SST to hold the flange, tighten the nut.
SST 09330−00021
NOTICE:
As there is no spacer, tighten a little at a time, being careful
not to overtighten.
(d) Using a torque wrench, measure the preload. Preload (at starting):
New bearing
0.9 − 1.6 N·m (10 − 16 kgf·cm, 8.7 − 13.9 in.·lbf)
Reused bearing
0.5 − 0.8 N·m (5 − 8 kgf·cm, 4.3 − 6.9 in.·lbf)
HINT:
Measure the total preload after first turning the bearing clock-
wise and counterclockwise several times to mark the bearing
smooth.
12. w/o DIFFERENTIAL LOCK: INSTALL DIFFERENTIAL CASE IN CARRIER
(a) Place the bearing outer races on their respective bear- ings. Make sure the left and right outer races are not inter-
changed.
(b) Install the case in the carrier.
HINT:
Make sure that there is backlash between the ring gear and
drive pinion.
13. w/ DIFFERENTIAL LOCK: INSTALL DIFFERENTIAL CASE IN CARRIER
(a) Apply MP grease on the rack of the shift fork and connect- ing part of the indicator switch.
(b) Insert the shift fork into the differential carrier, as shown.
(c) Install outer races, adjusting nuts and left side to sleeve.
HINT:
Check that the sleeve moves smoothly.
(d) Install the shift fork in the groove of the sleeve holding it by hand and install the case in the carrier.
HINT:
Make sure that there is backlash between the ring gear and
drive pinion.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010