1996 TOYOTA LAND CRUISER oil

−
ENGINE MECHANICAL CYLINDER BLOCK
EM−95
1996 LAND CRUISER (RM451U)
(1) Using a micrometer, measure the piston diameter at
right angles to the piston pin center line, 42 mm
(1.65 in.) from the piston head.
Piston diameter:
STD Mark ”1”
Mark ”2”
Mark ”3”99.950 − 99.960 mm (3.9350 − 3.9354 in.)
99.960 − 99.970 mm (3.9354 − 3.9358 in.)
99.970 − 99.980 mm (3.9358 − 3.9362 in.)
O/S 0.50100.450 − 100.480 mm (3.9547 − 3.9559 in.)
O/S 1.00100.950 − 100.980 mm (3.9744 − 3.9756 in.)
(2) Measure the cylinder bore diameter in the thrust
directions (See step 2).
(3) Subtract the piston diameter measurement from the
cylinder bore diameter measurement.
Standard oil clearance:
0.040 − 0.060 mm (0.0016 − 0.0024 in.)
Maximum oil clearance: 0.080 mm (0.0031 in.)
If the oil clearance is greater than maximum, replace all the 6
pistons and rebore all the 6 cylinders. If necessary, replace the
cylinder block.
HINT:
Use new cylinder block:
Use a piston with the same number mark as the cylinder bore
diameter marked on the cylinder block.
(b) Inspect the piston ting groove clearance. Using a feeler gauge, measure the clearance between
new piston ring and the wall of the piston ring groove.
Ring groove clearance:
No. 10.040 − 0.080 (0.0016 − 0.0031 in.)
No. 20.030 − 0.070 (0.0012 − 0.0028 in.)
If the clearance is greater than maximum, replace the piston.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P04002
125 mm
EM7639
P03829
EM−96
−
ENGINE MECHANICAL CYLINDER BLOCK
1996 LAND CRUISER (RM451U)
(c) Inspect the piston ring end gap.
(1) Insert the piston ring into the cylinder bore.
(2) Using a piston, push the piston ring a little beyondthe bottom of the ring travel, 125 mm (4.92 in.) from
the top of the cylinder block.
(3) Using a feeler gauge, measure the end gap.
Standard end gap:
No. 10.300 − 0.520 mm (0.0118 − 0.0205 in.)
No. 20.450 − 0.670 mm (0.0177 − 0.0264 in.)
Oil (Side rail)0.150 − 0.520 mm (0.0059 − 0.0205 in.)
Maximum end gap:
No. 11.12 mm (0.0441 in.)
No. 21.17 mm (0.0461 in.)
Oil (Side rail)1.12 mm (0.0441 in.)
If the end gap is greater than maximum, replace the piston ring.
If the end gap is greater than maximum, even with a new piston
ring, rebore all the 6 cylinders or replace the cylinder block.
(d) Inspect the piston pin fit.
At 80 − 90°C (176 − 194°F), you should be able to push
the piston pin into the piston pin hole with your thumb.
(e) Using a rod aligner and feeler gauge, check the connect- ing rod alignment.
(1) Check for out−of−alignment.
Maximum out−of−alignment:
0.05 mm (0.0020 in.) per 100 mm (3.94 in.)
If out− of−alignment is greater than maximum, replace the con-
necting rod assembly.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P03828
P03868
EM0227
−
ENGINE MECHANICAL CYLINDER BLOCK
EM−97
1996 LAND CRUISER (RM451U)
(2) Check for twist
Maximum twist:
0.15 mm (0.0059 in. ) per 100 mm (3.94 in.)
If twist is greater than maximum, replace the connecting rod as-
sembly.
(f) Inspect the piston pin oil clearance. (1) Using a caliper gauge, measure the inside diameter
of the connecting rod bushing.
Bushing inside diameter:
26.008 − 26.020 mm (1.0239 − 1.0244 in.)
(2) Using a micrometer, measure the piston pin diame-
ter.
Piston pin diameter:
26.000 − 26.012 mm (1.0236 − 1.0241 in.)
(3) Subtract the piston pin diameter measurement from
the bushing inside diameter measurement.
Standard oil clearance:
0.004 − 0.012 mm (0.0002 − 0.0005 in.)
Maximum oil clearance: 0.05 mm (0.0020 in.)
If the oil clearance is greater than maximum, replace the bush-
ing. If necessary, replace the piston and piston pin as a set (See
page EM−99 ).
(g) Inspect the connecting rod bolts. Install the cap nut to the connecting rod bolt. Check that
the cap nut can be turned easily by hand to the end of the
thread.
If the cap nut cannot be turned easily, measure the outside di-
ameter of the connecting rod bolt with vernier calipers. Standard outside diameter:
8.40 − 8.60 mm (0.3307 − 0.3386 in.)
Minimum outside diameter: 8.00 mm (0.3150 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM−98
−
ENGINE MECHANICAL CYLINDER BLOCK
1996 LAND CRUISER (RM451U)
HINT:
If the location of this area cannot be judged by visual inspection,
measure the outer diameter at the location shown in the illustra-
tion.
If the outside diameter is less than minimum, replace the con-
necting rod bolt and nut as a set.
6. INSPECT CRANKSHAFT
(a) Inspect for circle runout. (1) Place the crankshaft on V−blocks.
(2) Using a dial indicator, measure the circle runout atthe center journal.
Maximum circle runout: 0.06 mm (0.0024 in.)
If the circle runout is greater than maximum, replace the crank-
shaft.
(b) Inspect the main journals and crank pins. (1) Using a micrometer, measure the diameter of each
main journal and crank pin.
Main journal diameter:
STD68.982 − 69.000 mm (2.7158 − 2.7165 in.)
U/S 0.2568.745 − 68.755 mm (2.7065 − 2.7069 in.)
Crank pin diameter:
STD56.982 − 57.000 mm (2.2434 − 2.2441 in.)
U/S 0.2556.745 − 56.755 mm (2.2341 − 2.2344 in.)
If the diameter is not as specified, check the oil clearance (See
page EM−83 ). If necessary, grind or replace the crankshaft.
(2) Check each main journal and crank pin for taper and out−of−round as shown.
Maximum taper and out−of−round:
0.02 mm (0.0008 in.)
If the taper and out −of− round is greater than maximum, replace
the crankshaft.
7. IF NECESSARY, GRIND AND HONE MAIN JOURNALS
AND/OR CRANK PINS
Grind and hone the main journals and/or crank pins to the fin-
ished undersized diameter. Install new main journal and/or
crankshaft pin undersized bearings.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM1EI−02
P03827
P03867
−
ENGINE MECHANICAL CYLINDER BLOCK
EM−99
1996 LAND CRUISER (RM451U)
REPLACEMENT
1. REPLACE CONNECTING ROD BUSHING
(a) Using SST and a press, press out the bushing.
SST 09950 −60010 (09951 −00280), 09950 −70010
(09951 −07100)
(b) Align the oil holes of a new bushing and the connecting rod.
(c) Using SST and a press, press in the bushing. SST 09950 −60010 (09951 −00280), 09950 −70010
(09951 −07100)
(d) Using a pin hole grinder, hone the bushing to obtain the standard specified cliarance (See page EM−92) between
the bushing and piston pin.
(e) Check the piston pin fit at normal room temperature. Coat
the piston pin with engine oil, and push it into the connect-
ing rod with your thumb.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P04907
P08469
SST
EM−100
−
ENGINE MECHANICAL CYLINDER BLOCK
1996 LAND CRUISER (RM451U)
2. REPLACE OVERSIZED (O/S) PISTONS FOR CYLIN-
DER BORING
HINT:
Bore all the 6 cylinders for the O/S piston outside diame-
ter.
Replace all the piston rings with ones to match the O/S
pistons.
(a) Keep 6 new O/S pistons. O/S piston diameter:
O/S 0.50100.450 − 100.480 mm (3.9547 − 3.9559 in.)
O/S 1.00100.950 − 100.980 mm (3.9744 − 3.9756 in.)
(b) Using a micrometer, measure the piston diameter at right
angles to the piston pin center line, 42 mm (1.65 in.) from
the piston head.
(c) Calculate the amount of each cylinder is to be rebored as
follows:
Size to be rebored = P + C − H
P = Piston diameter
C = Piston oil clearance
0.040 − 0.060 mm (0.0016 − 0.0024 in.)
H = Allowance for honing
0.02 mm (0.0008 in.) or less
(d) Bore and hone the cylinders to calculated dimensions. Maximum honing: 0.02 mm (0.0008 in.)
NOTICE:
Excess honing will destroy the finished roundness.
3. REPLACE CRANKSHAFT FRONT OIL SEAL
HINT:
There are 2 methods ((a) and (b)) to replace the oil seal.
(a) If the timing chain cover is removed from the cylinder block:
(1) Using a screwdriver and a hammer, tap out the oilseal.
(2) Using SST and a hammer, tap in a new oil seal until
its surface is flush with the timing chain cover edge.
SST 09316−60011 (09316 −00011, 09316−00051)
(3) Apply MP grease to the oil seal lip.
NOTICE:
Do not let foreign matter get onto the lip of the oil seal.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P05005
P08506
SST
P04518
P04970
SST
P08643
Cut Position
−
ENGINE MECHANICAL CYLINDER BLOCK
EM−101
1996 LAND CRUISER (RM451U)
(b) If the timing chain cover is installed to the cylinder block:
(1) Using a screwdriver, pry out the oil seal.
NOTICE:
Be careful not to damage the crankshaft. Tape the screw-
driver tip.
(2) Apply MP grease to a new oil seal lip.
NOTICE:
Do not let foreign matter get onto the lip of the oil seal.
(3) Using SST and a hammer, tap in the oil seal until its
surface is flush with the timing chain cover edge.
SST 09316−60011 (09316 −00011, 09316−00051)
4. REPLACE CRANKSHAFT REAR OIL SEAL
HINT:
There are 2 methods ((a) and (b)) to replace the oil seal.
(a) If the rear oil seal retainer is removed from the cylinder block:
(1) Using a screwdriver and a hammer, tap out the oil
seal.
(2) Using SST and a hammer, tap in a new oil seal until
its surface is flush with the rear oil seal edge.
SST 09223−15030, 09950 −70010 (09951−07150)
NOTICE:
Do not let foreign matter get onto the lip of the oil seal.
(b) If the rear oil seal retainer is installed to the cylinder block:
(1) Using a knife, cut off the oil seal lip.
(2) Using a screwdriver, pry out the oil seal.
NOTICE:
Be careful not to damage the crankshaft. Tape the screw-
driver tip.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P23172
CORRECTWRONG
EM−102
−
ENGINE MECHANICAL CYLINDER BLOCK
1996 LAND CRUISER (RM451U)
(3) Using SST and a hammer, tap in a new oil seal until
its surface is flush with the rear oil seal retainer
edge.
SST 09223−15030, 09950 −70010 (09951−07150)
NOTICE:
Do not let foreign matter get onto the lip of the oil seal. (4) Check that the lip of the oil seal is not bent inward.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010