1996 LINCOLN CONTINENTAL Customer Assistance Guide

Tilt Steering/!\ WARNINGNever adjust the steering wheel when thevehicle is moving.94The lever to tilt the steering wheel

To change the position of the steering wheel, pull
the release lever on the column toward you. Tip
the steering wheel to the desired position.
Release the lever to lock the steering wheel in
place.
Speed Control
Your vehicle has speed control, so you can
automatically maintain a constant speed above 30
mph (48 km/h). The switches to operate the
speed control are on the steering wheel.
Use of radio transmitting equipment that is not
Federal Communications Commission (FCC) or
in Canada the Canadian Radio and
Telecommunications Commission (CRTC)
approved may cause the speed control to
malfunction. Therefore, use only properly
installed FCC (CRTC in Canada) approved radio
transmitting equipment in your vehicle.NOTE: Since your vehicle has an Automatic
Overdrive Transaxle, you may want to drive in D
(Drive) when driving in hilly terrain, at higher
altitudes, or when pulling a trailer. This will
improve speed control performance.
NOTE: Do not shift to N (Neutral) when using
the speed control. This will cause the engine to
overspeed.
95

The speed control switches on the steering
wheel
To set the speed control:
1.Press and release the ON switch.
2. Accelerate to the desired speed above 30 mph
(50 km/h) using the accelerator pedal.
963. Press the SET ACCEL switch and release it
immediately to set your speed. If you keep this
switch pressed, your speed will continue to
increase.
4.Take your foot off the accelerator pedal.
Your vehicle will maintain the speed you set.
If you drive up or down a steep hill, your vehicle
may momentarily slow down or speed up, even
though the speed control is on. This is normal.
When driving uphill, especially with a heavy load,
significant speed drops may occur. If the speed
drops more than 8-14 mph (13-23 km/h) the
automatic speed control will, by design, be
cancelled. If this happens, your vehicle may
require manual operation to maintain your desired
speed.

NOTE: If your speed increases above your set
speed while driving in (Overdrive) on a
downhill grade, you may want to shift to D
(Drive) to reduce vehicle speed. The speed
control cannot reduce the vehicle speed if it goes
above your set speed on a downhill grade. For
the best fuel economy during normal driving
conditions, leave the shift select in (Overdrive), or resume as soon as practical./! WARNINGDo not use the speed control in heavytraffic or on roads that are winding,slippery, or unpaved.Accelerating With the Speed Control
Operating
You can use the accelerator pedal to speed up
momentarily. When you take your foot off the
accelerator, the vehicle will return to the set
speed.Resetting the Speed Control
To reset the speed control to a lower speed, use
one of the following procedures: COAST - Press and hold the COAST switch.
Release the switch when the vehicle slows down
to the desired speed. Lightly tap the brake pedal. When the vehicle
attains the desired speed, press the SET
ACCEL switch and release it immediately. TAP-DOWN - Press and release the COAST
switch momentarily for each m.p.h. (1.6 km/h)
reduction in speed desired.
If vehicle speed is reduced below 30 mph (50
km/h) by any of the above methods, then you must
manually accelerate to a speed over 30 mph (50
km/h) and reset the system.
97

To reset the speed control to a higher speed,
follow one of these procedures: ACCEL - Press and hold the SET ACCEL
switch. Release the switch when the vehicle
has accelerated to the desired speed. Depress the accelerator pedal. When the
vehicle attains the desired speed, press the
SET ACCEL switch and release it
immediately. TAP-UP - Press and release the SET ACCEL
switch momentarily for each m.p.h. (1.6 km/h)
increase in speed desired.
To Cancel Speed Control
Speed control can be cancelled at any time by
pressing the brake pedal slightly. After
cancelling, you can return to the speed you set by
pressing the RES switch, or set a new speed by
pressing the SET ACCEL or COAST switches.
98To Turn Speed Control Off
Press the OFF switch.
Speed control is also turned OFF each time the
vehicle ignition is shut off.
Cancelling and Resuming a Set Speed
If you press the brake pedal, speed control is
suspended. You can return to the set speed by
pressing the RES switch, as long as you did not
press the OFF switch. You must be driving at least
30 mph (48 km/h).
Your vehicle will gradually return to the previously
set speed and then maintain it.

FeaturesYour vehicle has a variety of features designed for
your comfort, convenience and safety. Read this
chapter to find out about standard and optional
features.
Doors
Childproof Locks for the Rear Doors
In addition to power locks, your vehicle has
childproof locks for the rear doors. If you set these
locks, the rear doors cannot be opened from the
inside of the vehicle. The doors can still be opened
from the outside when the lock knobs are raised.Lock
The childproof locks for the rear doors
99

To set the childproof lock on each rear door, open
the rear door.
Find the lever at the black label with the word
LOCKED in white letters. Move the lever up.
To release the childproof lock, open the rear door
from the outside.
Move the lever down.
Using the Power Door Locks
Your vehicle has power door locks. The controls
to lock the doors are on the trim panel of the front
door. When you close the doors after you set the
door locks, the doors remain locked. If the power
mechanism ever fails, the manual door lock will
override the power controls.
100The power locks on the driver's door
Smart Locks
The Smart Locks feature helps prevent you from
locking the keys in your vehicle. With the key in
the ignition (in any switch position) and either
the driver's or passenger's door open, the doors
cannot be locked using the front door lock
switches.
NOTE: Your vehicle can still be locked, while
the key is in the ignition, by manually pressing
down the lock button or with remote/keyless
entry.

Illuminated Entry System with Theater
Lighting
The interior lights will illuminate for approximately
25 seconds when either front door handle is lifted,
any button on the keyless entry pad is pressed, or
the remote entry system UNLOCK button is
pushed. If the amount of light outside your vehicle
is below a predetermined level, the exterior lights
will also illuminate.
Using the Keyless Entry System
You can lock or unlock the vehicle doors and open
the trunk without using a key. The buttons for the
system are below the outside door handle on the
driver's side. See also Remote Entry System which
follows this description.The keyless entry buttons
When you bought your vehicle, you were given a
computer code that operates the system for your
vehicle. For your convenience, we have
duplicated this code in three places.
The code is: on your owner's wallet card found in the glove
compartment
101