1995 TOYOTA SUPRA engine oil

13. CONNECT ENGINE WIRE TO COWL PANEL
14. INSTALL A/C COMPRESSOR
(a) Using a torx socket (E10), install the stud bolt and and
compressor.
Torque: 26 NVm (265 kgfVcm, 19 ftVlbf)
(b) Connect the compressor connector.
(c) Temporarily install the compressor with nut and 3 bolts.
(d) Alternately tighten the bolt and nut.
Torque: 52 NVm (530 kgfVcm, 38 ftVlbf)
15. INSTALL PS PRESSURE TUBE
16. INSTALL PS PUMP
(a) Install the pump bracket with the 3 bolts.
Torque:
A 58 NVm (590 kgfVcm, 43 ftVlbf)
B 39 NVm (400 kgfVcm, 29 ftVlbf)
(b) Install the pump housing with the 2 bolts.
Torque: 58 NVm (590 kgfVcm, 43 ftVlbf)
(c) Connect these hoses:
wAir hose to throttle body
wAir hose to air intake chamber
17. CONNECT FUEL HOSES
(a) Connect the fuel return hose to the fuel return pipe.
(b) Install the fuel return hose to the clamp of the dipstick guide.
(c) Install the fuel inlet hose with 2 new gaskets and the union
bolt.
Torque: 29 NVm (300 kgfVcm, 22 ftVlbf)
18. CONNECT WIRES AND CONNECTORS
19. CONNECT EVAP HOSE
20. CONNECT BRAKE BOOSTER VACUUM HOSE
21. CONNECT HEATER WATER HOSES
22. INSTALL CHARCOAL CANISTER
23. INSTALL WATER PUMP PULLEY, FAN, FLUID COUPLING
ASSEMBLY AND DRIVE BELT
(See step 10 in water pump installation in Cooling Sys-
tem)
24. M/T:
INSTALL DRIVE BELT TENSIONER DAMPER
(See step 19 timing belt installation)
25. INSTALL AIR CLEANER AND MAF METER ASSEMBLY
26. INSTALL NO.1 AIR HOSE
27. CONNECT CONTROL CABLES TO THROTTLE BODY
28. FILL WITH FUEL
29. FILL WITH ENGINE OIL
30. START ENGINE AND CHECK FOR LEAKS
± ENGINEENGINE MECHANICALEG±131

31. CHECK IGNITION TIMING
(See ignition timing inspection)
32. INSTALL RADIATOR ASSEMBLY
(See radiator installation in Cooling System)
33. INSTALL HOOD
34. ROAD TEST VEHICLE
Check for abnormal noise, shock slippage, correct shift
points and smooth operation.
35. RECHECK ENGINE COOLANT AND ENGINE OIL LEVELS EG±132
± ENGINEENGINE MECHANICAL

 
 
 
Valve guide
Bushing 
 
 
Inside diameter
Outside diameter (for repair part) STD
O/S 0.05 
 
 
6.010±6.030 mm (0.2366±0.2374 in.)
11.033±11.044 mm (0.4344±0.4348 in.)
11.083±11.094 mm (0.4363±0.4368 in.)
 
 
 
 
 
 
 
 
 
 
 
Valve 
 
 
 
 
 
 
 
 
 
 
Valve overall length STD Intake
Exhaust
Minimum Intake
Exhaust
Valve face angle
Stem diameter Intake
Exhaust
Stem oil clearance STD Intake
Exhaust
Maximum Intake
Exhaust
Margin thickness STD
Minimum 
 
 
 
 
 
 
 
 
 
 
98.29±98.79 mm (3.8697±3.8894 in.)
98.84±99.34 mm (3.8913±3.9110 in.)
98.19 mm (3.8657 in.)
98.74 mm (3.8874 in.)
44.55
5.970±5.985 mm (0.2350±0.2356 in.)
5.965±5.980 mm (0.2348±0.2354 in.)
0.025±0.060 mm (0.0010±0.0024 in.)
0.030±0.065 mm (0.0012±0.0026 in.)
0.08 mm (0.0031 in.)
0.10 mm (0.0039 in.)
0.8±1.2 mm (0.031±0.047 in.)
0.5 mm (0.020 in.)
 
 
 
 
Valve spring
 
 
 
 
Deviation Maximum
Free length Blue painted mark
Yellow painted mark
Installed tension at 34.5 mm (1.358 in.)
 
 
 
 
2.0 mm (0.079 in.)
41.74 mm (1.6433 in.)
41.70 mm (1.6417 in.)
186±206 N (19.0±21.0 kgf, 42±46 lbf)
 
 
 
 
Valve lifter 
 
 
 
Lifter diameter
Lifter bore diameter
Oil clearance STD
Maximum 
 
 
 
30.966±30.976 mm (1.2191±1.2195 in.)
31.000±31.016 mm (1.2205±1.2211 in.)
0.024±0.050 mm (0.0009±0.0020 in.)
0.07 mm (0.0028 in.)
 
 
 
 
 
 
 
 
 
Camshaft 
 
 
 
 
 
 
 
 
Thrust clearance STD
Maximum
Cam lobe height STD Intake
Exhaust
Maximum Intake
Exhaust
Journal diameter
Journal oil clearance STD
Maximum
Circle runout Maximum 
 
 
 
 
 
 
 
 
0.080±0.190 mm (0.0031±0.0075 in.)
0.30 mm (0.0118 in.)
44.570±44.670 mm (1.7547±1.7587 in.)
44.770±44.870 mm (1.7626±1.7665 in.)
44.42 mm (1.7488 in.)
44.62 mm (1.7567 in.)
28.949±28.965 mm (1.1397±1.1404 in.)
0.035±0.072 mm (0.0014±0.0028 in.)
0.10 mm (0.0039 in.)
0.08 mm (0.0031 in.)
 
 Air intake
chamber 
 Warpage Maximum 
 0.15 mm (0.0059 in.)
 
 
 
Manifold 
 
 
Warpage Maximum Intake
Exhaust 2JZ±GE
2JZ±GTE 
 
 
0.15 mm (0.0059 in.)
0.50 mm (0.0196 in.)
0.80 mm (0.0315 in.)
 
 
 
 
 
Cylinder block 
 
 
 
 
Cylinder head surface warpage Maximum
Cylinder bore diameter STD
Maximum
Main bearing bolt diameter STD
Minimum 
 
 
 
 
0.07 mm (0.0028 in.)
86.000±86.013 mm (3.3858±3.3863 in.)
86.02 mm (3.3866 in.)
9.96±9.97 mm (0.3921±0.3925 in.)
9.7 mm (0.382 in.)
 
 
 
 
Connecting
Rod 
 
 
 
Thrust clearance STD
Maximum
Connecting bolt diameter STD
Minimum 
 
 
 
0.250±0.402 mm (0.0098±0.0158 in.)
0.50 mm (0.0197 in.)
8.1±8.3 mm (0.319±0.327 in.)
8.0 mm (0.315 in.)
EG±136± ENGINEENGINE MECHANICAL

 
 
 
 
 
 
 
 
 
 
 
 
 
 
Connecting
rod (cont'd) 
 
 
 
 
 
 
 
 
 
 
 
 
 
Connecting rod oil clearance STD STD
U/S 0.25
Maximum STD
U/S 0.25
Connecting rod bearing center wall thickness
(Reference) STD Mark 1
Mark 2
Mark 3
Mark 4
Mark 5
Bushing inside diameter
Piston pin diameter
Piston pin oil clearance STD
Maximum
Rod bent Maximum per 100 mm (3.94 in.)
Rod twist Maximum per 100 mm (3.94 in.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
0.035±0.053 mm (0.0014±0.0021 in.)
0.040±0.078 mm (0.0016±0.0031 in.)
0.08 mm (0.0031 in.)
0.09 mm (0.0035 in.)
1.492±1.495 mm (0.0587±0.0589 in.)
1.495±1.498 mm (0.0589±0.0590 in.)
1.498±1.501 mm (0.0590±0.0591 in.)
1.501±1.504 mm (0.0591±0.0592 in.)
1.504±1.507 mm (0.0592±0.0593 in.)
22.005±22.014 mm (0.8663±0.8667 in.)
21.997±22.006 mm (0.8660±0.8664 in.)
0.005±0.011 mm (0.0002±0.0004 in.)
0.05 mm (0.0020 in.)
0.05 mm (0.0020 in.)
0.15 mm (0.0059 in.)
 
 
 
 
 
 
 
 
 
 
Piston and
Piston ring
(2JZ±GE) 
 
 
 
 
 
 
 
 
 
Piston diameter
Piston oil clearance STD
Maximum
Piston ring groove clearance No.1
No.2
Piston ring end gap STD No.1
No.2
Oil
Maximum No.1
No.2
Oil 
 
 
 
 
 
 
 
 
 
85.935±85.945 mm (3.3833±3.3837 in.)
0.055±0.078 mm (0.0022±0.0031 in.)
0.10 mm (0.0039 in.)
0.011±0.070 mm (0.0004±0.0028 in.)
0.030±0.070 mm (0.0012±0.0028 in.)
0.300±0.470 mm (0.0118±0.0185 in.)
0.350±0.520 mm (0.0138±0.0205 in.)
0.130±0.450 mm (0.0051±0.0177 in.)
1.07 mm (0.0421 in.)
1.12 mm (0.0441 in.)
1.05 mm (0.0413 in.)
 
 
 
 
 
 
 
 
 
 
Piston and
Piston ring
(2JZ±GTE) 
 
 
 
 
 
 
 
 
 
Piston diameter
Piston oil clearance STD
Maximum
Piston ring groove clearance No.1
No.2
Piston ring end gap STD No.1
No.2
Oil
Maximum No.1
No.2
Oil 
 
 
 
 
 
 
 
 
 
85.917±85.927 mm (3.3826±3.3830 in.)
0.073±0.096 mm (0.0029±0.0038 in.)
0.12 mm (0.0047 in.)
0.040±0.080 mm (0.0016±0.0031 in.)
0.030±0.070 mm (0.0012±0.0028 in.)
0.300±0.400 mm (0.0118±0.0157 in.)
0.350±0.450 mm (0.0138±0.0178 in.)
0.130±0.380 mm (0.0051±0.0150 in.)
1.00 mm (0.0394 in.)
1.05 mm (0.0413 in.)
0.98 mm (0.0386 in.)
 
 
 
 
 
 
 
 
Crankshaft 
 
 
 
 
 
 
 
Thrust clearance STD
Maximum
Thrust washer thickness STD
Main journal oil clearance STD STD
U/S 0.25
Maximum STD
U/S 0.25
Main journal diameter STD
U/S 0.25 
 
 
 
 
 
 
 
0.020±0.220 mm (0.0008±0.0087 in.)
0.30 mm (0.0118 in.)
1.940±1.990 mm (0.0764±0.0783 in.)
0.026±0.040 mm (0.0010±0.0016 in.)
0.025±0.061 mm (0.0010±0.0024 in.)
0.06 mm (0.0024 in.)
0.08 mm (0.0031 in.)
61.984±62.000 mm (2.4403±2.4409 in.)
61.745±61.755 mm (2.4309±2.4313 in.)
± ENGINEENGINE MECHANICALEG±137

 
 
 
 
 
 
 
 
 
 
Crankshaft
(cont'd) 
 
 
 
 
 
 
 
 
 
Main bearing center wall thickness (Reference)
Mark 1
Mark 2
Mark 3
Mark 4
Mark 5
Crank pin diameter STD
U/S 0.25
Circle runout Maximum
Main journal taper and out±of±round Maximum
Crank pin taper and out±of±round Maximum 
 
 
 
 
 
 
 
 
 
1.994±1.997 mm (0.0785±0.0786 in.)
1.997±2.000 mm (0.0786±0.0787 in.)
2.000±2.003 mm (0.0787±0.0789 in.)
2.003±2.006 mm (0.0789±0.0790 in.)
2.006±2.009 mm (0.0790±0.0791 in.)
51.982±52.000 mm (2.0465±2.0472 in.)
51.745±51.755 mm (2.0372±2.0376 in.)
0.06 mm (0.0024 in.)
0.02 mm (0.0008 in.)
0.02 mm (0.0008 in.)
TORQUE SPECIFICATIONS
 Part tightened NVm kgfVcm ftVlbf
 Timing belt plate X Oil pump (2JZ±GTE) 7.8 80 69 in.Vlbf
 Idler pulley X Oil pump 34 350 25
 Crankshaft pulley X Crankshaft 324 3,300 239
 Camshaft timing pulley X Camshaft 79 810 59
Timing belt tensioner X Oil pump2627020 Drive belt tensioner X Cylinder head 21 210 15 Drive belt tensioner damper X Tensioner arm (2JZ±GTE M/T) 20 200 14 Drive belt tensioner damper X Tensioner bracket (2JZ±GTE M/T) 20 200 14 EGR cooler X Cylinder head 8.8 90 78 in.Vlbf ECT sensor X Cylinder head (2JZ±GE) 20 200 14 ECT sender gauge X Cylinder head (2JZ±GE) 20 200 14
 Engine hanger X Cylinder head 39 400 29
 Camshaft position sensor X Cylinder head (2JZ±GTE) 8.8 90 78 in.Vlbf
 
 
 
Cylinder head X Cylinder block 1st
2nd
3rd 



34
Turn 905
Turn 905 
 
 
350 
 
 
25
 Camshaft bearing cap X Cylinder head 20 200 14
 No.4 timing belt cover X Cylinder head 8.8 90 78 in.Vlbf
 Cylinder head cover X Cylinder head 2JZ±GE
2JZ±GTE 8.3
5.4 85
55 74 in.Vlbf
48 in.Vlbf
 
 Intake manifold X Cylinder head 2JZ±GE
2JZ±GTE 


27
27 
 280
280 
 20
20
 Fuel inlet pipe X Delivery pipe 42 420 30 Intake manifold stay X Intake manifold 39 400 29
 Intake manifold stay X Cylinder block 39 400 29
 Water outlet X Cylinder head (2JZ±GTE) 21 210 15
 Vacuum control valve set X Intake manifold (2JZ±GE) 21 210 15
 
 
Air intake chamber X Intake manifold 2JZ±GE
2JZ±GTE 


27
27 
 
280
280 
 
20
20
 Air intake chamber stay X Cylinder head (2JZ±GE) 18 185 13
 Air intake chamber stay X Air intake chamber (2JZ±GE) 18 185 13
 Exhaust manifold X Cylinder head 39 400 29
Pressure tank X Intake manifold (2JZ±GTE)2121015 
 Main bearing cap X Cylinder block 1st
2nd
 


44
Turn 905
 
 450
 
 33
EG±138± ENGINEENGINE MECHANICAL

 Connecting rod cap X Connecting rod 1st
2nd 29
Turn 905 300 22
 
Oil nozzle X Crankshaft (2JZ±GTE)
 
8.8
 
90
 
78 in.Vlbf Rear oil seal retainer X Cylinder block 5.9 60 52 in.Vlbf Crankshaft position sensor X Cylinder block (2JZ±GTE) 8.8 90 78 in.Vlbf Engine mounting bracket X Cylinder block 58 590 43 Engine coolant drain plug X Cylinder block 29 300 22 Union for oil cooler X Cylinder block (2JZ±GTE) 39 400 29
 Knock sensor X Cylinder block 44 450 33
 Oil pressure switch X Cylinder block 14 150 11
 Fuel pipe support X Cylinder block 14 145 10
 Oil filter bracket X Cylinder block 88 900 65
 No.2 water bypass pipe X Water pump 21 210 15
 No.2 water bypass pipe X Cylinder block 21 210 15
 Flywheel X Crankshaft (M/T) 1st
2nd 49
Turn 905 500 36
 Drive plate X Crankshaft (A/T) 83 850 61 Clutch cover X Flywheel (M/T) 19 195 14 
 Cylinder block X Transmission 14 mm head
17 mm head 
 39
72 
 400
730 
 29
43
 Clutch service hole cover X Clutch housing (2JZ±GTE M/T) 12 120 9
 Drive plate X Torque converter clutch (A/T) 33 340 25
 Oil cooler tube X Union for transmission (A/T) 34 350 25
 Rear support member X Body 25 260 19
 Rear support member X Engine rear mounting insulator 13 135 10
 Front suspension crossmember X Engine mounting insulator 59 600 43
 Transmission shift lever X Shift lever retainer (M/T) 19 195 14
 Transmission control rod X Shift lever (A/T) 13 130 9
Clutch release cylinder X Transmission (M/T)131309 
Clutch line tube X No.1 oil pan
 
37
 
380
 
27 Ground strap X Transmission (M/T) 37 380 27 Fuel inlet hose X Fuel pipe support 29 300 22 
 A/C compressor X Cylinder block for stud bolt
for bolt and nut 
 26
52 
 265
530 
 19
38
 PS pump front bracket X Cylinder block (2JZ±GE) 58 590 43
 PS pump front bracket X Oil pump (2JZ±GE) 52 530 38
 PS pump housing X PS pump bracket 58 590 43
 PS pump bracket X A/C compressor 58 590 43
 PS pump bracket X Cylinder block 39 400 29
 PS pump rear stay X PS pump bracket 39 400 29
 PS pump rear stay X Intake manifold stay (2JZ±GE) 39 400 29
 Rear center floor crossmember brace X Body (2JZ±GTE) 28 290 21
No.2 front exhaust pipe X Exhaust manifold6263046 No.2 front exhaust pipe X Front exhaust pipe 58 590 43 Pipe support bracket X Transmission 43 440 32 Front exhaust pipe X Center exhaust pipe 58 590 43 Center exhaust pipe X Tailpipe 19 195 14 
 
Sub heated oxygen sensor
x Front exhaust pipe (2JZ±GE (California), 2JZ±GTE) 
 
20 
 
200 
 
14
± ENGINEENGINE MECHANICALEG±139

09205±76030Cylinder Head Setting Bolt
Tightening Adaptor
09268±41045Injection Measuring Tool Set
(09268±41070)No.4 Union
(09268±41090)No.7 Union
(90405±09015)No.1 Union
09268±45012 EFI Fuel Pressure Gauge
ECT sensor
09612±24014 Steering Gear Housing Overhaul
Tool Set
(09617±24011) Steering Rack Wrench
09631±22020 Power Steering Hose Nut
14 x 17 mm Wrench Set
09808±14010Fuel Sender Gauge Tool Assy
09816±30010 Oil Pressure Switch Socket
09842±30070 Wiring ªFº EFI InspectionInjector
Knock sensor
Fuel line flare nut
Fuel pressure pulsation damper
SFI SYSTEM (2JZ±GE)
PREPARATION
SST (SPECIAL SERVICE TOOLS)
± ENGINESFI SYSTEM (2JZ±GE)EG±187

PRECAUTION
1. Before working on the fuel system, disconnect the
negative (±) terminal cable from the battery.
HINT: Any diagnostic trouble code retained by the computer
will be erased when the negative (±) terminal cable is discon-
nected.
Therefore, if necessary, read the diagnosis before discon-
necting the negative (±) terminal cable from the battery.
2. Do not smoke or work near an open flame when working
on the fuel system.
3. Keep gasoline away from rubber or leather parts.
MAINTENANCE PRECAUTIONS
1. PRECAUTION WHEN CONNECTING GAUGE
(a) Use ba tte ry as th e po we r so u rce fo r th e timin g lig h t,
tachometer, etc.
(b) Connect the tester probe of a tachometer to the terminal IG

of the DLC1.
2. IN EVENT OF ENGINE MISFIRE, FOLLOWING
PRECAUTIONS SHOULD BE TAKEN
(a) Check proper connection of battery terminals, etc.
(b) Handle high±tension cords carefully.
(c) After repair work, check that the ignition coil terminals and all
other ignition system lines are reconnected securely.
(d) When cleaning the engine compartment, be especially
careful to protect the electrical system from water.
3. PRECAUTIONS WHEN HANDLING OXYGEN SENSOR
(a) Do not allow oxygen sensor to drop or hit against an object.
(b) Do not allow the sensor to come into contact with water.
± ENGINESFI SYSTEM (2JZ±GE)EG±189