1995 TOYOTA SUPRA engine coolant

DTC 42 No. 1 Vehicle Speed Sensor Signal Circuit
CIRCUIT DESCRIPTION
The No.1 vehicle speed sensor outputs a 4±pulse signal for every revolution of the rotor shaft, which
is rotated by the transmission output shaft via the driven gear. After this signal is converted into a more
precise rectangular waveform by the waveform shaping circuit inside the odometer and trip meter, it is
then transmitted to the engine control module. The ECM determines the vehicle speed based on the
frequency of these pulse signals.
DTC No.Diagnostic Trouble Code Detecting ConditionTrouble Area
For A/T
All conditions below are detected
Continuously for 8 sec. or more:
(a) No.1 vehicle speed signal: 0 km/h
(mph)
(b) Engine speed: 3,000 rpm or more
(c) Park/neutral position switch: OFF
(d) Stop light switch: OFF
For A/T
All conditions below are detected
Continuously for 8 sec. or more:
(a) No.1 vehicle speed signal: 0 km/h
(mph)
(b) Engine speed: Between 1,500 rpm
and 4,000 rpm
(c) Engine coolant temp.: 80°C (176°F)
or more
(d) Load driving

No.1 vehicle speed sensor

Telltale light RH (Odometer and trip meter)

Open or short in No.1 vehicle speed sensor
circuit

ECM
HINT: In test mode, diagnostic trouble code 42 is output when vehicle speed is 5 km/h (3 mph) or
below.

Waveform between terminals SP1 and E1 when vehicle
speed is approx. 20 km/h (12mph).
HINT: As the vehicle speed increases, the number of signals
from SP1 increases. EG±556
± ENGINE2JZ±GTE ENGINE TROUBLESHOOTING

See page EG±503.
CIRCUIT DESCRIPTION
The EGR system is designed to recirculate the exhaust gas, controlled according to the driving condi-
tions back into the intake air±fuel mixture. It helps to slow down combustion in the cylinder and thus
lower the combustion temperature which, in turn, reduces the amount of NO
x emission. The amount
of EGR is regulated by the EGR vacuum modulator according to the engine load.
If even one of the following conditions is fulfilled,
the VSV is turned ON by a signal from the ECM.
This resists in atmospheric air acting on the EGR
valve, closing the EGR valve and shutting off the
exhaust gas (EGR cut±OFF).

Engine coolant temp. below 50°C (122°F)

During deceleration (throttle valve closed)

Light engine load (amount of intake air very
small)

Engine speed over 4,800 rpm

Manifold absolute pressure more than 120 kPa
(1.2 kgf/cm
2, 17.4 psi)
DTC No.Diagnostic Trouble Code Detecting ConditionTrouble Area
No No.1 knock sensor signal to ECM for 4
crank revolutions with engine speed between
2,050 rpm and 5,950 rpm

Open EGR gas temp. sensor circuit

Short in VSV circuit for EGR

EGR hose disconnected, valve stuck

Clogged EGR gas passage

ECM
EGR gas temp. and intake air temp. are
60°C(140°F) or less for A/T, 55°C (131°F) or
less for M/T for 1 ~ 4 min. under conditions (a)
and (b):
(2 trip detection logic)*
(a) Engine coolant temp.: 60°C (140°F) or
more
(b) EGR operation possible (Example A/T in
3rd speed (5th for M/T), A/C ON, 96 km/h
(60 mph), Flat road)
Purpose of the driving pattern.
(a) To simulate diagnostic trouble code detecting condition after diagnostic trouble code is recorded.
(b) To check that the malfunction is corrected when the repair is completed by confirming that diagnos±
tic trouble code is no longer detected.
DIAGNOSTIC TROUBLE CODE DETECTION DRIVING PATTERN
DTC 71 EGR System Malfunction
EG±564± ENGINE2JZ±GTE ENGINE TROUBLESHOOTING

VSV Circuit for Fuel Pressure Control
CIRCUIT DESCRIPTION
The ECM turns on a VSV (Vacuum Switching
Valve) to draw air into the diaphragm chamber
of the pressure regulator if it detects that the
temperature of the engine coolant is too high
during engine starting.
The air drawn into the chamber increases the
fuel pressure to prevent fuel vapor lock at high
engine temperature in order to help the en-
gine start when it is warm.
Fuel pressure control ends approx. 120 sec.
after the engine is started.
± ENGINE2JZ±GTE ENGINE TROUBLESHOOTINGEG±595

TURBOCHARGER SYSTEM (2JZ±GTE)
PREPARATION
SST (SPECIAL SERVICE TOOLS)
09992±00241 Turbocharger Pressure Gauge
EQUIPMENT
 
 
Dial indicator 
 
Impeller wheel
 
 
Torque wrench 
 
COOLANT
 Item Capacity Classification
 
 Engine coolant (w/ Heater) M/T
A/T 
  9.5 liters (10.0 US qts. 8.4 lmp. qts)
9.4 liters (9.9 US qts, 8.3 lmp. qts) 
 Ethylene±glycol base
EG±140± ENGINETURBOCHARGER SYSTEM (2JZ±GTE)

TURBOCHARGER REMOVAL
Installation is in the reverse order of removal.
1. DRAIN ENGINE COOLANT
2. REMOVE ENGINE UNDER COVER
3. DISCONNECT CRUISE CONTROL ACTUATOR CABLE
FROM THROTTLE BODY
4. REMOVE NO.1 AIR HOSE
5. REMOVE AIR CLEANER DUCT
6. REMOVE AIR CLEANER AND MAF METER ASSEMBLY
(a) Remove the 3 bolts.
(b) Loosen the hose clamp, disconnect the air hose from the
intake air connector.
(c) Disconnect the MAF meter wire from the clamp on the air
cleaner case.
(d) Disconnect the MAF meter connector, and remove the air
cleaner and MAF meter assembly. EG±150
± ENGINETURBOCHARGER SYSTEM (2JZ±GTE)