1995 RENAULT MEGANE SCENIC steering

SPECIAL NOTES FOR BOSCH MONOPOINT INJECTION
• Use the XR25 with the latest cassette and fiche n° 28.
Read the computer Part Number using code G70*.
Erase the memory using code G0**.
• Injection warning light operational (see principle of ignition section).
• Maximum engine speed before ignition cut-out: 6 500 rpm.
• Corrected idle speed after operation of the air conditioning: 900 rpm.
• Corrected idle speed with wheels at full lock (power assisted steering pressostat information) : 825 rpm.
• Canister bleed solenoid valve controlled by RCO signal depending on engine operating conditions (the
valve is not operated for no load).
• If there is a fault with the absolute pressure sensor, the manifold pressure is recreated depending on the
throttle position and the engine speed.
• Reading of the default values from the air temperature sensor (#03) or coolant temperature sensor (#02),
not the values taken in defect mode by the computer when they are recognised as being faulty.
• There is a+after ignition input (track 30) to inform the computer that the ignition has been turned off
while it remains fed for a few seconds to reposition the idle speed micromotor.
(Avoids false detection of a fault in the engine immobiliser system).
INJECTION
General
17
E7J engine
FITTING A 2ND GENERATION ENGINE IMMOBILISER REQUIRES A SPECIAL PROCEDURE FOR REPLACING THE
COMPUTER.
17-6

INJECTION
General
17
K7M engine
SPECIAL NOTES FOR MULTIPOINT INJECTION
•55 track SIEMENS FENIX 5 computer.
•Semi-sequential multipoint injection. Injectors controlled in pairs (injectors for cylinders 1 and 4 then
injectors for cylinders 2 and 3).
•Static ignition with two coils.
•Canister bleed solenoid controlled by RCO signal.
•EGR solenoid valve controlled by RCO signal (K7M 703).
•Idle speed correction depending on:
- air conditioning,
- heated windscreen,
- power assisted steering pressostat.
•Injection warning light on instrument panel operational.
•Use fault finding fiche N° 27.
FITTING A 2ND GENERATION ENGINE IMMOBILISER REQUIRES A SPECIAL PROCEDURE FOR REPLACING THE
COMPUTER.
17-8

INJECTION
General
17
K7M engine
1Injection computer
2Pinking sensor
3Coolant temperature sensor
4TDC sensor
5Fuel vapour recirculation solenoid valve
7Idle speed regulation stepping motor
8Throttle position potentiometer
9Air temperature sensor
10Absolute pressure sensor
11Canister
12Coil for cylinders 1 - 4
13Coil for cylinders 2 - 3
14Fuel pump relay
15Anti-interference condenser
16Air filter
17Oxygen sensor
18Power assisted steering pressostat
19EGR solenoid valve
20Vacuum reservoir
21EGR air filter
LOCATION OF COMPONENTS
17-9

INJECTION
Location of components
17
K7M engine
19EGR solenoid valve
99358-2R
18Power assisted steering pressostat
99362R
17-14

INJECTION
Idle speed correction
17
POWER ASSISTED STEERING PRESSOSTAT - INJECTION COMPUTER CONNECTION (K7M and E7J engines)
The injection computer receives information from the power assisted steering pressostat. This depends on the
pressure in the hydraulic circuit. The higher the pressure, the more energy is used by the power assisted
steering pump.
The injection computer, to compensate for this energy use, increases the percentage opening of the idle
speed regulation stepping motor for the K7M engine or adjusts the idle speed micromotor for the E7J
engine.
The information is received on track 13 (K7M engine) and track 8 (E7J engine) on the injection computer.
Pressostat closed, the computer receives an earth. The idle speed is adjusted to 820 rpmfor the K7M engine
and 825 rpm for the E7J engine.
IDLE SPEED CORRECTION DEPENDING ON THE BATTERY VOLTAGE (F3R engine)
This correction compensates for the drop in voltage due to operation of consumers when the battery is poorly
charged. To do this, the idle speed is increased, allowing the alternator to rotate more and consequently
increase the charging voltage.
The lower the voltage, the greater the degree of correction. Correction of the engine speed is therefore
variable. It begins when the voltage drops to below 12.7 Volts. Correction begins at the nominal engine
speed and may reach a maximum of 910 rpm.
IDLE SPEED CORRECTION DEPENDING ON HEATED WINDSCREEN INFORMATION
The E7J engine has no heated windscreen.
If the heated windscreen function is selected, the computer receives + 12 V information :
on track 6 for K7M engines
on track 5 for F3R engines.
If the coolant temperature is less than 60°C, the idle speed is set to :
- 1 000 rpm (F3R engine)
- 850 rpm (K7M engine)
17-32

INJECTION
Operating wiring diagram
17
KEY TO OPERATIONAL WIRING DIAGRAMS (E7J, F3R, K7M)
COMPONENT NO DESCRIPTION
109
119
120
146
147
149
193 to 196
218
222
224
225
228
236
238
242
244
247
250
272
310
319
341
371
398
437
565
597
645
649
663
664
679
746
772
777
927
MF
MHOn board computer
Automatic transmission computer
Injection computer
Pinking sensor (located under the inlet manifold for E7J engine)
Absolute pressure sensor
TDC sensor
Injectors
Fuel pump
Throttle position potentiometer
Power assisted steering pressostat
Diagnostic socket
Idle speed regulation micromotor
Fuel pump relay (in engine fuse box)
Injection feed locking relay
Oxygen sensor
Coolant temperature sensor
Instrument panel
Vehicle speed sensor
Air temperature sensor
Ignition power module
Air conditioning control panel
Idle speed regulation solenoid valve
Fuel vapour recirculation solenoid valve
Exhaust gas recirculation solenoid valve (EGR)
Throttle body heater (under throttle body)
Throttle body assembly
Engine fuse box
Passenger compartment connection unit
Idle speed regulation stepping motor
Dual ignition coil n°1 (cylinders 1 and 4)
Dual ignition coil n° 2 (cylinders 2 and 3)
Radio anti-interference condenser
Cylinder reference sensor
Heater relay (in engine fuse box)
Power fuse board (near battery)
Inertia switch
Rear right hand electrical earth
Engine electrical earth (located on the cylinder block between the starter and the al-
ternator for the E7J engine)
17-39

INJECTION
Operating wiring diagram
17
E7J engine
COMPUTER TRACK ALLOCATION
TrackALLOCATION
1Power earth
2Electronic earth
3Vehicle speed information
4+ before ignition (permanent) computer memory
5Canister bleed signal (sequential earth period)
6Pump relay control (via track N° 2)
7Locking relay control (via track N° 2)
8Diagnostic line for erasing the memory and power assisted steering pressostat information
9Throttle position potentiometer information (pin N° 4 on 222)
10Heater relay command
11TDC sensor signal (track B)
12Rev counter information at instrument panel
13Connection with injection fault warning light on instrument panel
14Air temperature information
15Coolant temperature information
16+ 5 V feed for absolute pressure sensor and throttle potentiometer
17Common earth for absolute pressure sensor, throttle potentiometer and coolant temperature
sensor
18Emission of diagnostic signal to diagnostic socket
19Main computer feed via injection locking relay
20Air conditioning compressor command
21Injector control via earth
22Not used
23+ or - feed to idle speed micromotor (pin N° 1)
24+ or - feed to idle speed micromotor (pin N° 2)
17-41

INJECTION
Operating wiring diagram
17
K7M engine
COMPUTER TRACK ALLOCATION
TrackALLOCATION
1Not used
2Power earth n° 1
3Power earth n° 2
4Command for injector n° 2 and n° 3 via earth
5Air conditioning on - off information and request for compressor operation authorisation
(0 - 12 V)
6Heated windscreen information (0 - 12 V)
7Park / Neutral / torque reduction information (0 - 5 V) (K7M 703)
8Pinking sensor signal
9Stepping motor control (0 - 12 V)
10EGR solenoid valve control (0 - 12 V) (K7M 703)
11Bi-directional diagnostic line K used for entry into fault finding mode
(looking for computer), emission of diagnostic signals from computer, application of command
modes (G..*), erasing the memory (G0**)
and ending fault finding (G13*)
12Vehicle speed information
13Power assisted steering pressostat information
14Not used
15Coolant temperature sensor information
16Manifold pressure information transcribed by absolute pressure sensor
17Voltage information from oxygen sensor
18Earth
19Throttle position potentiometer information
20Air temperature sensor information
21Not used
22Not used
23Not used
24+ 12 V after ignition
17-44