1995 RENAULT MEGANE SCENIC oil type

Page
COOLING
Specifications
Filling - bleeding
Checking
Radiator
Diagram
Exhaust
General
Catalytic converter
Exhaust pipe assembly
Fuel tank
Fuel tank
Filler neck
Gauge
Pump and sender unit
Engine suspension
Suspended engine mountings
Engine mounting pads19-1
19-2
19-3
19-4
19-6
19-12
19-15
19-16
19-19
19-23
19-25
19-26
19-29
19-32 COOLING - EXHAUST- FUEL TANK -
ENGINE SUSPENSION
1916-1
16-9 STARTING - CHARGING
Alternator
Starter motor
16
IGNITION - INJECTION
IGNITION
Power module
Static ignition
Spark plugs
Injection
General
Location of components
Special notes on semi-sequential
injection
Special notes on sequential injection
Injection fault warning light
Engine immobiliser function
Computer configuration as a
function of the gearbox type
17
14-1
14-9
14-13
14-19
14-21
14-22 ANTIPOLLUTION
Fuel vapour recirculation
Oil vapour rebreathing
Exhaust gas recirculation (EGR)
Catalytic converter
Catalytic converter - oxygen sensor
Test for the presence of lead
14
17-28
17-29
17-32
17-33
17-34
17-36
17-39 IGNITION - INJECTION
(continued)
Injection strategy / automatic
transmission
Injection strategy / air conditioning
Idle speed correction
Idle speed adaptive correction
Richness regulation
Adaptive richness correction
Operating wiring diagram
17
Page
17-1
17-2
17-5
17-6
17-12
17-17
17-19
17-24
17-25
17-26
Contents

FUEL MIXTURE
Specifications
12
DESCRIPTION MAKE/TYPE SPECIAL NOTES
ComputerSIEMENS FENIX 555 tracks
Injection Semi-sequential regulated multipoint injection
Ignition Static with two dual output coils
Power module integral in computer
One pinking sensor
Plugs
EYQUEM FC 52 LS
CHAMPION C10YCGap: 0.9 mm
Tightening torque: 2.5 to 3 daN.m
Air filter Replace every other oil change
Fuel filter Mounted in front of the fuel tank under the vehicle
Replace at major service
Fuel pump
WALBROSubmerged in fuel tank
Flow: 80 litres/hour minimum for regulated
pressure of 3 bars and voltage of 12 V
Pressure regulator Regulated pressure
Zero vacuum: 3 ± 0.2 bars
Vacuum of 500 mbar : 2.5 ± 0.2 bars
Solenoid injector
SIEMENSVoltage: 12 V
Resistance : 14.5 ± 1 Ω
Throttle body
PIERBURG
714 186Diameter 44 mm
Idle speed regulation stepping
motor
EGR (K7M 703) solenoid valve
PIERBURG
72213000Voltage: 12 V
Resistance : 30 ± 3 Ω
Fuel vapour recirculation
canister
Solenoid valve
CAN 10
DELCO REMY
Voltage: 12 V
Resistance : 35 ± 5 Ω
Heated oxygen sensor NGK Voltage at 850°C
Rich mixture: > 625 mvolt
Lean mixture: 0 to 80 mvolt
Tightening torque: 4.5 daN.m
Fault finding
FICHE n° 27
CODE D13
SELECTOR ON S8
Throttle potentiometer
Idle speed regulation: 5 ≤ #17 ≤ 47
Full load: 164 ≤ #17 ≤ 253
R.C.O. idle speed: 4 % ≤ #12 ≤ 14 % (K7M 720)
6 % ≤ #12 ≤ 15 % (K7M 702/703 in P and N)
10 % ≤ #12 ≤ 20 % (K7M 703 in D)
Adaptive R.C.O
idle speed: - 2.4 % ≤ #21 ≤ + 6.2%
Adaptive richness
operation: 0 ≤ #30 ≤ 208
Adaptive richness
idle speed: 100 ≤ #31 ≤ 255 (K7M 720)
104 ≤ #31 ≤ 255 (K7M 702/703)
12-4

FUEL MIXTURE
Specifications
12
DESCRIPTION MAKE/TYPE SPECIAL NOTES
ComputerSIEMENS FENIX 555 tracks
Injection Sequential regulated multipoint injection
Ignition Static with two dual output coils
Power module integral in computer
One pinking sensor
Plugs
EYQUEM C 52 LS
CHAMPION N7YCX
BOSCH W7DCOGap: 0.9 mm
Tightening torque: 2.5 to 3 daN.m
Air filter Replace every other oil change
Fuel filter Mounted in front of the fuel tank under the vehicle
Replace at major service
Fuel pump
WALBROSubmerged in fuel tank
Flow: 80 litres/hour minimum for regulated
pressure of 3 bars and voltage of 12 V
Pressure regulator WEBER
BOSCHRegulated pressure
Zero vacuum: 3 ± 0.2 bars
Vacuum of 500 mbar : 2.5 ± 0.2 bars
Solenoid injector
SIEMENSVoltage: 12 V
Resistance: 14.5 ± 1 Ω
Throttle body SOLEX
Diameter 60 mmReference: 127 F3R 751 without AC - F3R 750
Reference: 132 F3R 751 AC
Idle speed regulation solenoid
HITACHI
AESP 207-17Voltage: 12 V
Resistance: 9.5 ± 1 Ω
Fuel vapour recirculation
canister
Solenoid valve
CAN 10
DELCO REMY
Voltage: 12 V
Resistance: 35 ± 5 Ω
Heated oxygen sensor
BOSCH LSH 25Voltage at 850°C
Rich mixture: > 625 mvolt
Lean mixture: 0 to 80 mvolt
Tightening torque: 4.5 daN.m
Fault finding
FICHE n° 27
CODE D13
SELECTOR ON S8
Throttle potentiometer
Idle speed regulation: 8 ≤ #17 ≤ 38
Full load: 188 ≤ #17 ≤ 245
R.C.O. idle speed: 20 % ≤ #12 ≤ 40 % (F3R 750)
18 % ≤ #12 ≤ 38 % (F3R 751)
Adaptive R.C.O
idle speed: - 6.2 % or - 8.6 ≤ #21 ≤ + 6.2 %
Adaptive richness
operation: 82 ≤ #30 ≤ 224
Adaptive richness idle speed: 32 ≤ #31 ≤ 224
12-6

98900-1R
IGNITION
Static ignition
17
The differences between static ignition with two
coils and distributed ignition are:
- the high voltage distributor is no longer used,
- two dual output coils are used.
PRESENTATION
The system comprises:
- the injection computer (the ignition power
stage is integrated into the computer),
- two dual output coils,
- four spark plugs,
- an anti-interference condenser.
DESCRIPTION - OPERATING PRINCIPLE
COMPUTER
The injection computer (120), depending on the
information received from various sensors, but
principally depending on the engine speed and
load, determines:
- the number of degrees of advance to be used
and consequently the ignition point,
- which cylinders are at TDC and consequently
the ignition coil to be operated.
The spark is created at the two cylinders at TDC by
cutting the earth to the coil concerned.
COILS
There are two coils. They are of the dual output
type.
They are controlled separately by the computer.
They create two sparks at the same time.They have a foolproofing device (K7M engine):
- on their base to prevent them being fitted in-
correctly to the rocker box cover,
- at the retaining clips for the high voltage
leads.
They are colour coded on the 3 track electrical
connectors.
Coil (2) has a black electrical connector. This coil
provides the sparks for cylinders 1 and 4 at the
same time. It is controlled by track 28 on the injec-
tion computer.
Coil (3) has a grey electrical connector. This coil
provides the sparks for cylinders 2 and 3 at the
same time. It is controlled by track 29 on the injec-
tion computer.
Both coils are connected to an anti-interference
condenser (1).
F3R engine
F3R - K7M
engines
17-2

INJECTION
General
17
F3R engine
SPECIAL NOTES FOR MULTIPOINT INJECTION
•55 track SIEMENS FENIX 5 computer.
•Injection cylinder by cylinder (sequential).
•Static ignition with two coils.
•Canister bleed solenoid controlled by RCO signal.
•Idle speed correction depending on:
- battery voltage,
- air conditioning,
- heated windscreen.
•Injection warning light on instrument panel operational.
•Use fault finding fiche N° 27.
•Computer configuration depending on gearbox type (manual gearbox or automatic transmission).
FITTING A 2ND GENERATION ENGINE IMMOBILISER REQUIRES A SPECIAL PROCEDURE FOR REPLACING THE
COMPUTER.
17-10

Oil pressure
Before starting:
- if the gearbox has been drained, fill it with 3.5
litres of oil,
- if you are simply checking the level, you must
add 0.5 litre of the recommended type of oil.
1-Vehicle on a 4 post lift, transmission at am-
bient temperature.
2-Start the engine with the selector lever in the
Park position.
3-Connect the
XR25 test kit and enter:
D14then
#0 4
4-Raise the vehicle and allow the engine to run
until it reaches a temperature of 60 °C.
5-When the desired temperature has been rea-
ched, open the top-up plug; allow the excess
oil to overflow (must be more than 0.1 litre)
for approximately 20 seconds. Replace the
plug
6-If the volume of oil which flowed out is less
than 0.1 litre, the level is not correct. Repeat
the operation.
In this case, add 1 litre of the recommended oil
and allow the transmission to cool down between
successive operations.
AUTOMATIC TRANSMISSION
Filling - Levels
23
FILLING - TOPPING UP
Filling is performed though tube (D).
Use a funnel fitted with a 15/100 filter so as to
prevent any impurities entering.
The level
MUST be checked in accordance with the
following method:
94845R1
The transmission is fitted with an oil pressure
take-off. Connect the B.Vi. 1215 to check the
automatic transmission pressure sensor only.
The oil pressure cannot be altered.
Its value is determined by the electronic compu-
ter.
94845-1R
23-8

MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Hydraulic system reservoir
52
PRE5205
RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
RR R R
EE E E
FF F F
II I I
TT T T
TT T T
II I I
NN N N
GG G G
Coat the O-ring with hydraulic oil.
Fit the seal in the oil reservoir groove.
Position the reservoir on the pump.
Tighten the bolts (2) to a torque of 7 N.m.
II I I
MM M M
PP P P
OO O O
RR R R
TT T T
AA A A
NN N N
TT T T
:: : :
the hood must be closed when the
hydraulic system is filled.
Fill the reservoir with
EE E E
SS S S
SS S S
OO O O

UU U U
NN N N
II I I
VV V V
II I I
SS S S

JJ J J
22 2 2
66 6 6 oil (capaci-
ty 0.75 l).
The oil level must be between the MINIMUM and
MAXIMUM marks.
The hydraulic system is of the "AUTOMATIC
BLEED" type. The oil level
MM M M
UU U U
SS S S
TT T T
be checked with
the hood open, hood cover closed.
Check the oil level and top up if necessary.
Switch on the ignition, apply the handbrake.
Operate the hood switch.
Open and close the hood several times.
The bleeding process is completed when move-
ment is regular and without jolts with a constant
level of pump noise. Remove:
- the filler bolt (1) and drain,
- the reservoir mounting bolts (2).
12297-1R
52-16