Page
COOLING
Specifications
Filling - bleeding
Checking
Radiator
Diagram
Exhaust
General
Catalytic converter
Exhaust pipe assembly
Fuel tank
Fuel tank
Filler neck
Gauge
Pump and sender unit
Engine suspension
Suspended engine mountings
Engine mounting pads19-1
19-2
19-3
19-4
19-6
19-12
19-15
19-16
19-19
19-23
19-25
19-26
19-29
19-32 COOLING - EXHAUST- FUEL TANK -
ENGINE SUSPENSION
1916-1
16-9 STARTING - CHARGING
Alternator
Starter motor
16
IGNITION - INJECTION
IGNITION
Power module
Static ignition
Spark plugs
Injection
General
Location of components
Special notes on semi-sequential
injection
Special notes on sequential injection
Injection fault warning light
Engine immobiliser function
Computer configuration as a
function of the gearbox type
17
14-1
14-9
14-13
14-19
14-21
14-22 ANTIPOLLUTION
Fuel vapour recirculation
Oil vapour rebreathing
Exhaust gas recirculation (EGR)
Catalytic converter
Catalytic converter - oxygen sensor
Test for the presence of lead
14
17-28
17-29
17-32
17-33
17-34
17-36
17-39 IGNITION - INJECTION
(continued)
Injection strategy / automatic
transmission
Injection strategy / air conditioning
Idle speed correction
Idle speed adaptive correction
Richness regulation
Adaptive richness correction
Operating wiring diagram
17
Page
17-1
17-2
17-5
17-6
17-12
17-17
17-19
17-24
17-25
17-26
Contents
ANTIPOLLUTION
Catalytic converter - oxygen sensor
14
CHECKS TO BE MADE BEFORE THE ANTI-
POLLUTION TEST
Ensure:
- the ignition system is operating correctly
(correct spark plugs, correctly set plug gap,
high voltage leads in good condition and
correctly connected).
- the injection system is operating correctly
(supply is correct - check using the XR25).
- the exhaust pipe is correct and is sealed.
- the EGR is operating correctly.
Check the vehicle history if possible (run out of
fuel, lack of power, use of incorrect fuel).
CHECKING ANTI-POLLUTION STANDARDS
Run the engine until the engine cooling fan has
operated twice.
Connect a correctly calibrated four gas analyser to
the exhaust tail pipe.
Keep the engine speed at 2500 rpm for
approximately 30 seconds then let the engine
return to idle speed and note the pollutant values.
CO
≤0.3 %
CO
2≥14.5 %
HC
≤100 ppm
0,97
≤λ≤1.03
1
NOTE : λ = ————
richness
λ>1→lean mixture
λ<1→rich mixture
If, after these tests, the values are correct, the
antipollution system is correct.
If the values are not correct, additional tests must
be carried out:
- Check the condition of the engine (condition
of the oil, valve clearances, timing, etc,...),
- Check the correct operation of the oxygen
sensor (see section 17) ,
- test for the presence of lead (see following
page).
If the test for the presence of lead is positive, en-
sure the vehicle uses two or three full tanks of un-
leaded fuel before replacing the oxygen sensor.
If, after all these tests have been carried out, the
values still do not conform, the catalytic converter
must be replaced. Petrol engine
14-21
98900-1R
IGNITION
Static ignition
17
The differences between static ignition with two
coils and distributed ignition are:
- the high voltage distributor is no longer used,
- two dual output coils are used.
PRESENTATION
The system comprises:
- the injection computer (the ignition power
stage is integrated into the computer),
- two dual output coils,
- four spark plugs,
- an anti-interference condenser.
DESCRIPTION - OPERATING PRINCIPLE
COMPUTER
The injection computer (120), depending on the
information received from various sensors, but
principally depending on the engine speed and
load, determines:
- the number of degrees of advance to be used
and consequently the ignition point,
- which cylinders are at TDC and consequently
the ignition coil to be operated.
The spark is created at the two cylinders at TDC by
cutting the earth to the coil concerned.
COILS
There are two coils. They are of the dual output
type.
They are controlled separately by the computer.
They create two sparks at the same time.They have a foolproofing device (K7M engine):
- on their base to prevent them being fitted in-
correctly to the rocker box cover,
- at the retaining clips for the high voltage
leads.
They are colour coded on the 3 track electrical
connectors.
Coil (2) has a black electrical connector. This coil
provides the sparks for cylinders 1 and 4 at the
same time. It is controlled by track 28 on the injec-
tion computer.
Coil (3) has a grey electrical connector. This coil
provides the sparks for cylinders 2 and 3 at the
same time. It is controlled by track 29 on the injec-
tion computer.
Both coils are connected to an anti-interference
condenser (1).
F3R engine
F3R - K7M
engines
17-2
