1995 NISSAN ALMERA N15 check transmission fluid

Fluidleakage TROUBLE
DIAGNOSES
Preliminary Check(PriortoRoad Testing)
AIT FLUID CHECK
Fluid leakage check

1. Clean areasuspected ofleaking, -for example, mating
surface ofconverter housingandtransmission case.
2. Start engine, applyfootbrake, placeselector leverin"0"
position andwait afew minutes.
3. Stop engine.
4. Check forfresh leakage.

SAT288G
Fluidcondition check
Fluid levelcheck -Refer toMA section (CHASSIS AND
BODY MAINTENANCE).
Fluid
color
Oark orblack withburned odor
Milky pink
Varnished fluid,lighttodark brown
and tacky Suspected
problem
Wear offrictional material
Water contamination
- Road water entering through
filler tubeorbreather
Oxidation
- Over orunder filling
- Overheating

•

Road Testing

Perform roadtests using "Symptom" chart.Refertopage

AT-20.

"P"
POSITION

1. Place selector leverin"P" position andstart engine. Stop
engine andrepeat theprocedure inall positions, including
neutral position.
2. Stop vehicle onaslight upgrade andplace selector leverin
"P" position. Releaseparkingbraketomake surevehicle
remains locked.

"R"
POSITION

1. Manually moveselector leverfrom"P"to"R", andnote
shift quality.
2. Drive vehicle inreverse longenough todetect slippage or
other abnormalities.

"N"
POSITION

1. Manually moveselector leverfrom"R"and"0"to"N" and
note shift quality.
2. Release parkingbrakewithselector leverin"N" position.
Lightly depress accelerator pedaltomake surevehicle
does notmove. (When vehicle isnew orsoon afterclutches
have been replaced, vehiclemaymove slightly. Thisisnot
a problem.)

AT-17

HOWTOUSE THIS MANUAL

ManualTransaxle/Transmission
Automatic Transaxle/
Transmission
Air Conditioner
Power Steering
Special Service Tools
Society ofAutomotive Engineers,

Inc.

Automatic Transmission Fluid
Drive range 1stgear
Drive range 2ndgear
Drive range 3rdgear
Drive range 4thgear
Overdrive
2nd range 2ndgear
2nd range 1stgear
1st range 2ndgear
1st range 1stgear

A/C
PIS

Tool SAE
ATF

0
1

O
2

0
3

0
4

00

2
2

2
1
1
2

1
1

•
The following
SYMBOLS ANDABBREVIATIONS
areused:

to;J,
l\tI
Tightening torque M/T

IE!
Shouldbelubricated withgrease. A/T
Unless otherwise indicated,use
recommended multi-purpose
grease.
Should belubricated withoil.
Sealing point
Checking point
Always replaceafterevery disas-
sembly.
Apply petroleum jelly.
Apply ATF.
Select withproper thickness.
Adjustment isrequired.
Service DataandSpecifications
Left-Hand, Right-Hand
Front, Rear

IE!
~

@

*

1I
SDS LH, RH

FR, RR
• The
UNITS
giveninthis manual areprimarily expressed asthe SlUNIT (International SystemofUnit),
and alternatively expressedinthe metric system andinthe yard/pound system.

"Example" Tightening torque:
59 -78 N'm (6.0-8.0 kg-m, 43-58 ft-Ib)
• TROUBLE DIAGNOSES
areincluded insections dealingwithcomplicated components.

• SERVICE DATAANDSPECIFICATIONS
arecontained atthe end ofeach section forquick reference
of data.
• The captions
WARNING
and
CAUTION
warnyouofsteps thatmust befollowed toprevent personal
injury and/or damage tosome partofthe vehicle.

WARNING
indicatesthepossibility ofpersonal injuryifinstructions arenotfollowed.

CAUTION
indicatesthepossibility ofcomponent damageifinstructions arenotfollowed.

BOLD TYPED STATEMENTS
except
WARNING
and
CAUTION
giveyouhelpful information.

GI-8

PRE-DELIVERYINSPECTIONITEMS
Shown belowarePre-delivery InspectionItemsrequired forthe new vehicle. Itis recommended that
necessary itemsotherthanthose listedherebeadded, payingdueregard tothe conditions ineach
country.

Perform applicable itemsoneach model. Consult textofthis section forspecifications .

UNDER HOOD-engine off

o
Radiator coolantlevelandcoolant hosecon-
nections forleaks

o
Battery fluidlevel, specific gravityandcondi-
tions ofbattery terminals

o
Drive beltstension

D
Fuel filter forwater ordusts, andfuel lines
and connections forleaks
[] Engine oillevel andoilleaks

D
Clutch andbrake reservoir fluidlevel and
fluid lines forleaks

o
Windshield andrear window washerand
headlamp cleanerreservoir fluidlevel

D
Power steering reservoir fluidlevel andhose
connections forleaks

ON INSIDE ANDOUTSIDE

D
Remove frontspring/strut spacer(Ifapplica-
ble)

D
Operation ofall instruments, gauges,lights
and accessories

o
Operation ofhorn(s), wiperandwasher
[] Steering lockforoperation
[] Check airconditioner forgas leaks

o
Front andrear seats, andseat belts foroper-
ation

n
All moldings, trimsandfittings forfitand
alignment

[J
Allwindows foroperation andalignment

n
Hood, trunklid,door panels forfitand align-
ment

[1
Latches, keysandlocks foroperation

rl
Weatherstrips foradhesion andfit

[l
Headlamp aiming
I~ Tighten wheelnuts(Inc. inner nutsifapplica-
ble)
IJ Tire pressure (Inc.spare tire)

Il
Check frontwheels fortoe-in
IJ Install clock/voltmeter/room lampfuse(If
applicable)
~ Install deodorizing filtertoair purifier (If
applicable)
~ Remove wiperbladeprotectors (Ifapplicable)
UNDER
BODY

o
Manual transmission/transaxle, transferand
differential gearoillevel

D
Brake andfuel lines andoil/fluid reservoirs
for leaks

D
Tighten boltsandnuts ofsteering linkageand
gear box,suspension, propellershaftsand
drive shafts
~ Tighten rearbody boltsandnuts (Models with
wooden bedonly)

ROAD TEST

D
Clutch operation

D
Parking brakeoperation

[J
Service brakeoperation

D
Automatic transmission/transaxle shifttiming
and kickdown
[] Steering controlandreturnability

o
Engine performance

D
Squeaks andrattles

ENGINE OPERATING ANDHOT

D
Adjust idlemixture andspeed (andignition
timing*1)

n
Automatic transmission/transaxle fluidlevel
~ Engine idlingandstop knob operation (Diesel
only)

FINAL INSPECTION

n
Install necessary parts(outside mirror,wheel
covers, seatbelts, mat,carpet ormud flaps)

[1
Inspect forinterior andexterior metaland
paint damage
[] Check forspare tire,jack, tools (wheel
chock), andliterature

n
Wash, cleaninterior andexterior

"1: Not required onmodels withadirect ignition system
~ :Not appiicable tothis model.
•

MA-5

0
0
•

0
0

~ /0
H

H

0
0

(2)
4wheels
5 wheels

SMA785C

Radial
tires
CHASSIS
ANDBODY MAINTENANCE
Tire Rotation

Do not include theT-type sparetirewhen rotating thetires .

Wheel nuts:
~: 98-118 N'm (10.0 -12.0 kg-m, 72-87 ft-Ib)

Q :
Check grease leakage
• :Check tightening torque
Checking
SteeringGearandLinkage
STEERING GEAR

• Check gearhousing andboots forlooseness, damageor
grease leakage.
• Check connection withsteering columnforlooseness.

STEERING LINKAGE

• Check balljoint, dustcover andother component partsfor
looseness, wear,damage orgrease leakage.

SMA851B
Checking PowerSteering FluidandLines

• Check fluidlevel withengine off.
• Check fluidlevel using dipstick onreservoir cap,orrefer-
ring tothe scale onreservoir tank.Use"HOT" rangeatfluid
temperatures of50 to80°C (122to176°F). Use"COLD"
range atfluid temperatures of
a
to 30°C (32to86°F).

CAUTION:
• Donot overfill.
• Recommended fluidisAutomatic Transmission Fluid
''DEXRON™,, typeorequivalent.
SST280B
SST476C
•Check linesforimproper attachment, leaks,cracks,
damage, looseconnections, chafinganddeterioration.
• Check rackboots foraccumulation ofpower steering fluid.

MA-50

ON-VEHICLESERVICE
Checking andAdjusting DriveBelts(Forpower
steering)

Refer to"Checking DriveBelts" for"ENGINE MAINTENANCE"
in MA section.

SST476C

S
r

SST681B Checking
Fluidlevel

Check fluidlevel using dipstick onreservoir cap,orreferring to
the scale onreservoir tank.
Use "HOT" rangeforfluid temperatures of50 to80°C (122to

176°F).

Use "COLD" rangeforfluid temperatures of0to 30°C (32to

86°F).
CAUTION:
• Donot overfill.
• Recommended fluidisAutomatic Transmission Fluid
''DEXRON™,, typeorequivalent.
Checking Fluidleakage

Check thelines forimproper attachment andforleaks, cracks,
damage, looseconnections, chafingordeterioration.
1. Run engine between idlespeed and1,000 rpm.

Make suretemperature offluid inoil tank rises to60 to80°C
(140 to176°F).

2. Turn steering wheelright-to-Ieft severaltimes.
3. Hold steering wheelateach "lock" position forfive seconds
and carefully checkforfluid leakage.

CAUTION:
Do not hold thesteering wheelinalocked position formore
than 15seconds.

4. Iffluid leakage atconnectors isnoticed, loosenflarenutand
then retighten.

Do not overtighten connectorasthis candamage O-ring,
washer andconnector.

5. Check rackboots foraccumulation ofpower steering fluid.

ST-6

POWERSTEERING GEARANDLINKAGE (ModelPR24AC)
Disassembly

1. Prior todisassembling, measurepinionrotating torque.
Record thepinion rotating torqueasareference.

• Before measuring, disconnectgearhousing tubeanddrain
fluid.
• Use softjaws when holding steering gearhousing. Handle
gear housing carefully, asitis made ofaluminum. Donot
grip cylinder inavise.

2. Remove piniongear.

Be careful nottodamage piniongearwhen removing pinion
seal ring.

3. Remove tie-rodoutersockets andboots.
4. Loosen tie-rodinnersocket byprying upstaked portion, and
remove socket.
5. Remove retainer.
6. Remove pinionassembly.
7. Use a2to 2.5 mm (0.079 to0.098 in)diameter drilltocom-
pletely remove stakedportion ofgear housing end.
8. Remove endcover assembly withasuitable tool.
9. Draw outrack assembly.
10. Remove rackseal ring.
• Using aheat gun,heat racksealtoapproximately 40°C
(104°F).
• Remove racksealring.

Be careful nottodamage rack.

11. Remove centerbushing andrack oilseal using tape
wrapped socketandextension bar.

Do not scratch innersurfaces ofpinion housing .

.. !tension bar
29 mm socket

SST472AInspection

Thoroughly cleanallparts incleaning solventorautomatic
transmission fluid''DEXRON™,, typeorequivalent. Blowdry
with compressed air,ifavailable.

BOOT

• Check condition ofboot. Ifcracked excessively, replaceit.
• Check bootsforaccumulation ofpower steering fluid.

RACK

Thoroughly examinerackgear. Ifdamaged, crackedorworn,
replace it.

ST-22