1995 NISSAN ALMERA N15 fluids

ENGINEMAINTENANCE
@[]

Changing EngineCoolant (Cont'd)

2. Open drainplugs onthe bottom rightofradiator andonthe
left side ofcylinder block.
3. Remove radiatorcapand drain coolant.
4. Close drainplugs andfillradiator withwater uptofiller •
neck. •
5. Warm upengine andrepeat steps2,3and 4one ortwo
times todrain oldcoolant.

Drain plug(Radiator)

6.Open airbleeder onintake manifold.
7. Fill radiator withcoolant uptofiller neck.
Follow instructions attachedtoanti-freeze containerforanti-
freeze towater mixing ratio.

Pour coolant slowlytoallow airinsystem toescape.
Coolant capacity:

Regarding theAnti-freeze CoolantMixtureRatio,referto"REC-
OMMENDED FLUIDSANDLUBRICANTS".
8. Securely closeairbleeder.
9. Fill reservoir tankwithcoolant upto"MAX" level.
10. Warm upengine atabout 2,000rpmtonormal operating
temperature.
11. Stop engine andallow
it
to cool.
12. Check coolant levelandrefill reservoir tankifnecessary.

• Clean excess coolant fromengine.

MAX.

MIN.

SMA412B
With
heater
Without heater
5.2
(4-5/8)
4.9 (4-3/8)
Unit:
C(Imp qt)

Water outlet
SLC053B CAUTION:
When heater unitisremoved orreplaced, refillengine coolant
as shown, removing heaterhoseatfeeding connector on
engine.
MA-39

CHASSISANDBODY MAINTENANCE

Changing
MIT
Oil

1. Drain oilfrom drain plugandrefill withnewgear oil.
2. Check oillevel. (Refer to"Checking
M/T
Oil".)
Oil grade:

API GL-4

Viscosity: See "RECOMMENDED FLUIDSANDLUBRICANTS",
MA-14.
Capacity: RS5F30A 2.8-3.0f
(4-7/8 -5-114
Imppi)
RS5F31A 2.9-3.2£
(5-1/8 -5-518
Imppt)
RS5F32A 3.7-3.9£ (6-112 -
6-7/8
Imppt)
Drain plug:

(OJ:
15-20 N'm (1.5-2.0 kg-m, 11-14 ft-Ib)
6. Check fluidcondition. Iffluid isvery dark orsmells burned,
or contains frictionmaterial (clutches, band,etc.),check
operation ofAlT. Refer toAT section forchecking operation

of AlT.

Checking

AIT
Fluid Level

1. Warm upengine .
2. Check forfluid leakage.
3. Before driving, fluidlevel canbechecked atfluid tempera-
tures of30 to50°C (86to122°F) using"COLD" rangeon
dipstick.
a. Park vehicle onlevel surface andsetparking brake.
b. Start engine andmove selector leverthrough eachgear
position. Leaveselector leverin"P" position.
c. Check fluidlevel withengine idling.
d. Remove dipstickandnote reading. Iflevel isat low side of
either range, addfluid tothe charging pipe.
e. Re-insert dipstickintocharging pipeasfar asitwill go.

f.
Remove dipstickandnote reading.
If
reading isat low side
of range, addfluid tothe charging pipe.Donot overfill.
4. Drive vehicle forapproximately 5minutes inurban areas.
5. Re-check fluidlevel atfluid temperatures of50 to80°C (122
to 177°F) using"HOT" rangeondipstick.

SMA827C
SMA579CB

GA
engine models

• Front side

HOT [50•80°C (122•176°F))

OK

SR engine models

• Front side
HOT [50•80"C (122-176"F)]

o'f..

Check fluidforcontamination.

SMA853B
MA-46

CHASSISANDBODY MAINTENANCE
OK MINMax,
line
Min, line
SBR418C Changing
AITFluid

1. Warm up
AIT
fluid.
2. Stop engine.
3. Drain
AIT
fluid from drain plugandrefill withnew
AIT
fluid .•
Always refillwithsame volume asdrained fluid.
i

Fluid grade:
Genuine NissanATForequivalent
See "RECOMMENDED FLUIDSANDlUBRICANTS",
MA-14.
Fluid capacity (Withtorque converter):
7.0£
(6-1/8
Impqt)
Drain plug:

toJ:
29.39
N'm
(3.0-4.0
kg-m,
22-29
ft-Ib)

4. Run engine atidle speed forfive minutes.
5. Check fluidlevel andcondition. Referto"Checking
AIT

Fluid". Iffluid isstill dirty, repeat steps2through 5.

Checking BrakeFluidLevel andLeaks
If
fluid level isextremely low,check brakesystem forleaks.

Checking BrakeSystem

Check brakefluidlines andparking brakecables forimproper
attachment andforleaks, chafing, abrasions, deterioration, etc.

SBR404C Changing
BrakeFluid

1. Drain brake fluidfrom each airbleeder valve.
2. Refill untilnewbrake fluidcomes outfrom each airbleeder
valve. Use same procedure asinbleeding hydraulic systemto
refill brake fluid.
Refer to"CHECK ANDADJUSTMENT" inBR section.

• Refill withrecommended brakefluid.
See "RECOMMENDED FLUIDSANDlUBRICANTS".
• Never reusedrained brakefluid.
• Becareful nottosplash brakefluidonpainted areas.
MA-47