1994 JEEP CHEROKEE fuel tank removal

A blue wire (without a connector) located under in-
strument panel near fuse panel is available for
trailer electric brake control unit.
The stop lamp and turn signal plug-in relays are
located behind left quarter trim panel.
HITCH REMOVALÐXJ VEHICLES
An XJ class III, weight-distributing/equalizer type
hitch is comprised of:
²a towing tube with a ball mount receptacle, and²various reinforcement/support brackets that are at-
tached to the vehicle frame sills and rear crossmem-
ber with bolts.
(1) If necessary, remove the trailer tow wire har-
ness connector from the hitch.
(2) Support the hitch.
(3) Remove the bolts that attach the towing tube
to the frame sills and reinforcement bracket. If
equipped, remove the fuel tank skid plate.
Fig. 14 Equalizer Type HitchÐXJ Vehicles
Fig. 12 Class III Trailer Tow Wire Harness and
ConnectorsFig. 13 Class III Trailer Tow Wire Harness Plug-In
Relays
JBODY COMPONENTSÐXJ VEHICLES 23 - 89

The valve incorporates a pressure relief mechanism
(Fig. 11) that releases fuel tank pressure when the
pressure increases above the calibrated sealing
value. Refer to the Fuel Tank section of Group 14,
Fuel Systems for removal and installation proce-
dures.
Fig. 10 Pressure Relief/Rollover Valve
LocationÐTypicalFig. 11 Pressure Relief/Rollover Valve Operation
25 - 6 EMISSION CONTROL SYSTEMSJ

COMPONENT REMOVAL/INSTALLATION
INDEX
page page
Air Cleaner Housing....................... 8
Air Filter................................ 9
Coolant Temperature Sensor................. 9
EVAP Canister........................... 9Fuel Tank Filler Tube Cap.................. 9
Oxygen (O2S) Sensor...................... 9
Powertrain Control Module (PCM)............. 9
Pressure Relief/Rollover Valve................ 9
AIR CLEANER HOUSING
REMOVAL
(1) Unlock clean air hose clamp (Figs. 3 or 4) at
air cleaner cover. To unlock the clamp, attach adjust-
able pliers to clamp and rotate pliers as shown in fig-
ure 3. Remove clean air hose at cover.
(2) Disconnect vacuum lines at air cleaner hous-
ing.
(3) YJ Models: Release the three over-center type
clamps securing the housing to the housing bracket.
XJ Models: Remove the housing cover and remove
air filter. Remove two bolts and one nut.
(4) Release the air cleaner housing from the ambi-
ent air inlet and remove housing from vehicle.
INSTALLATION
(1) Position air cleaner housing to body and ambi-
ent air inlet.
(2) YJ Models: Lock the three over-center type
clamps securing the housing to the housing bracket.
XJ Models: Install two bolts and one nut to housing.Fig. 3 Air CleanerÐXJ ModelsÐTypical
Fig. 4 Air CleanerÐYJ ModelsÐTypical
Fig. 5 Clamp Removal
25 - 8 EMISSION CONTROL SYSTEMSJ

Install air filter and cover.
(3) Install vacuum lines to housing.
(4) Install clean air hose and clamp to cover. Com-
press the clamp snugly with adjustable pliers as
shown in figure 6.
AIR FILTER
REMOVAL/INSTALLATION
(1) Pry back the six clips (YJ Models) or three clips
(XJ Models) retaining the air cleaner cover to the air
cleaner housing.
(2) Lift the cover up and position to the side.
(3) Remove air filter.
(4) Clean the inside of air cleaner housing before
installing new filter.
(5) Reverse the preceding operation for installa-
tion. Be sure the air cleaner cover is properly seated
to air cleaner housing.
COOLANT TEMPERATURE SENSOR
For description, operation, diagnosis and removal/
installation procedures of the engine coolant temper-
ature sensor, refer to Group 14, Fuel Systems.
EVAP CANISTER
On XJ models, the EVAP canister is located in the
engine compartment on the passenger side frame rail
(Fig. 7). On YJ models, the EVAP canister is located
in the engine compartment on the dash panel and be-
low the brake master cylinder (Fig. 8).
REMOVAL/INSTALLATION
(1) Disconnect the vacuum lines at the EVAP can-
ister. Note location of lines before removal.
(2) Remove canister retaining strap bolt.
(3) Remove canister from vehicle.Reverse the procedure for installation.
FUEL TANK FILLER TUBE CAP
If replacement of the fuel filler tube cap is neces-
sary, it must be replaced with an identical cap to be
sure of correct system operation.
OXYGEN (O2S) SENSOR
For description, operation, diagnosis and removal/
installation procedures of the O2S sensor, refer to
Group 14, Fuel Systems.
POWERTRAIN CONTROL MODULE (PCM)
For removal and installation procedures, refer to
Group 14, Fuel Systems.
PRESSURE RELIEF/ROLLOVER VALVE
For removal and installation procedures, refer to
the Fuel Tank section of Group 14, Fuel Systems.
Fig. 7 EVAP CanisterÐXJ Models
Fig. 8 EVAP CanisterÐYJ Models
Fig. 6 Clamp Installation
JEMISSION CONTROL SYSTEMS 25 - 9

BODY SOLENOIDS, TRANSMISSION
VALVE ............................21-175
BODY STRIPES/DECALS...........23-25,23-153
BODY, THROTTLE.................14-29,14-59
BODY UNDERCOAT....................23-203
BOOSTER CHECK VALVE TEST, POWER......5-11
BOOSTER INSTALLATION, POWER
BRAKE..........................5-23,5-51
BOOSTER OPERATION, POWER BRAKE......5-22
BOOSTER, POWER BRAKE............5-22,5-40
BOOSTER REMOVAL, POWER BRAKE . . . 5-22,5-51
BOOSTER TEST, MASTER CYLINDER/
POWER.............................5-11
BOOSTER VACUUM TEST, POWER..........5-12
BORES, HONING CYLINDER................9-2
BOX, GLOVE.........................23-194
BRACKET, FUEL FILTER.................23-86
BRACKET, FUEL FILTER SHIELD...........13-17
BRACKET, I/P TWEETER SPEAKER/
COURTESY LAMP SUPPORT............23-95
BRACKET, MUFFLER/TAILPIPE HANGER.....13-16
BRACKET, REARVIEW MIRROR
RETAINING........................23-183
BRACKET REPLACEMENT, INTERIOR
REARVIEW MIRROR SUPPORT..........23-75
BRACKETS, CATALYTIC CONVERTER/
MUFFLER/TAILPIPE SUPPORT...........23-85
BRACKETSÐXJ VEHICLES, SPARE TIRE/
WHEEL HOLDDOWN AND FLOOR.......23-128
BRAKE ADJUSTMENT, DRUM..............5-35
BRAKE ADJUSTMENT PARKING............5-63
BRAKE BLEEDINGÐBRAKE FLUID AND
LEVELÐBRAKELINES AND HOSES........5-13
BRAKE BLEEDINGÐWITH ABS BRAKES.....5-14
BRAKE BLEEDINGÐWITH STANDARD
BRAKES.............................5-13
BRAKE BOOSTER INSTALLATION,
POWER.........................5-23,5-51
BRAKE BOOSTER OPERATION, POWER......5-22
BRAKE BOOSTER, POWER............5-22,5-40
BRAKE BOOSTER REMOVAL, POWER . . . 5-22,5-51
BRAKE CABLE TENSIONER REPLACEMENT
(XJ), PARKING........................5-61
BRAKE CHECK, PRELIMINARY..............5-7
BRAKE COMPONENTS, WHEEL.............5-1
BRAKE DIAGNOSIS, ABS..................5-3
BRAKE DIAGNOSIS, SERVICE..............5-7
BRAKE DRUM REFINISHING..............5-37
BRAKE FLUID CONTAMINATION............5-13
BRAKE FLUID, IMPORTANCE OF CLEAN.....5-48
BRAKE FLUID LEVEL....................5-13
BRAKE FLUID, RECOMMENDED........5-13,5-48
BRAKE FLUID TUBE RETAINER CLIP,
FUEL AND; BODY COMPONENTSÐXJ
VEHICLES..........................23-86
BRAKE FLUID TUBE RETAINER CLIP,
FUEL AND; FRAME AND BUMPERS......13-16
BRAKE FLUID/LUBRICANTS/CLEANING
SOLVENTS............................5-1
BRAKE FRONT CABLE REPLACEMENT
(YJ), PARKING........................5-62
BRAKE INDICATOR INOPERATIVE..........8E-4
BRAKE INDICATOR LAMP; INSTRUMENT
PANEL AND GAUGESÐXJ...............8E-2
BRAKE INDICATOR LAMP; INSTRUMENT
PANEL AND GAUGESÐYJ
..............8E-16
BRAKE LEVER INSTALLATION (XJ WITH
FULLCONSOLE), PARKING
..............5-60
BRAKE LEVER INSTALLATION (XJ WITH
MINICONSOLE), PARKING
...............5-58
BRAKE LEVER INSTALLATION (XJ
WITHOUT CONSOLE), PARKING
..........5-60
BRAKE LEVER REMOVAL (XJ WITH FULL
CONSOLE), PARKING
..................5-59
BRAKE LEVER REMOVAL (XJ WITH MINI
CONSOLE), PARKING
..................5-58
BRAKE LEVER REMOVAL (XJ WITHOUT
CONSOLE), PARKING
..................5-60
BRAKE OPERATION, PARKING
.............5-56
BRAKE OVERHAUL, SECOND
............21-232
BRAKE PACK REQUIREMENTS, AW-4
CLUTCH
...........................21-328
BRAKE PEDAL AND BRAKELIGHT
SWITCH
.............................5-65
BRAKE PEDAL INSTALLATION
.............5-66BRAKE PEDAL INSTALLATION (YJ),
PARKING............................5-61
BRAKE PEDAL REMOVAL.................5-65
BRAKE PEDAL REMOVAL (YJ), PARKING....5-61
BRAKE PEDAL SERVICE..................5-65
BRAKE PISTON AND TRANSMISSION
CASE OVERHAUL, FIRST-REVERSE......21-237
BRAKE PROBLEMS, DIAGNOSING
PARKING............................5-10
BRAKE PROBLEMS, DIAGNOSING
SERVICE.............................5-8
BRAKE REAR CABLE REPLACEMENT
(XJ), PARKING........................5-62
BRAKE REAR CABLE REPLACEMENT (YJ),
PARKING............................5-63
BRAKE ROTOR REFINISHING, DISC.........5-32
BRAKE ROTOR RUNOUT, DISC............5-31
BRAKE ROTOR THICKNESS, DISC..........5-31
BRAKE ROTOR THICKNESS VARIATION,
DISC...............................5-31
BRAKE SAFETY PRECAUTIONS.............5-2
BRAKE SERVO, SECOND COAST.........21-181
BRAKE SWITCH.......................14-54
BRAKE SWITCHÐPCM INPUT............14-20
BRAKE SYSTEM (ABS), ANTILOCK..........5-1
BRAKE SYSTEM (ABS) INDICATOR
LAMP, ANTI-LOCK.....................8E-2
BRAKE SYSTEM OPERATION, ANTILOCK.....5-43
BRAKE SYSTEM, POWER.................0-32
BRAKE TORQUE SPECIFICATIONS..........5-67
BRAKE WARNING LIGHT DISPLAY...........5-4
BRAKE WARNING LIGHTS.................5-1
BRAKELIGHT SWITCH ADJUSTMENT........5-66
BRAKELIGHT SWITCH, BRAKE PEDAL.......5-65
BRAKELIGHT SWITCH INSTALLATION.......5-66
BRAKELIGHT SWITCH REMOVAL...........5-66
BRAKELINE CHARTS....................5-15
BRAKELINES AND HOSES................5-15
BRAKELINING MATERIAL..................5-1
BRAKES, BRAKE BLEEDINGÐWITH ABS.....5-14
BRAKES, BRAKE BLEEDINGÐWITH
STANDARD..........................5-13
BRAKES, DISC.........................5-24
BRAKES, DRUM........................5-34
BRAKES, PARKING......................5-56
BRAKES, POWER........................5-1
BRAKESHOE INSTALLATION, DISC..........5-26
BRAKESHOE INSTALLATION, DRUM........5-34
BRAKESHOE REMOVAL, DISC.............5-25
BRAKESHOE REMOVAL, DRUM............5-34
BRAKING MODE, ABS OPERATION IN
ANTILOCK...........................5-43
BRAKING MODE, ABS OPERATION
IN NORMAL..........................5-43
BREAK-IN, ENGINE......................0-13
BRUSH GUARD........................23-3
BUCKET SEAT COMPONENTS, POWER....23-106
BUCKET SEAT CUSHION AND COVER......23-98
BUCKET SEAT PLATFORM AND TRACKS . . . 23-105
BUCKET SEATBACK COVER AND FRAME . . . 23-100
BUCKET SEATBACK RECONDITIONING.....23-102
BUCKET SEATS, FRONT.................23-97
BUFFING AND POLISHING..............23-203
BULB REPLACEMENT, BACK-UP/REAR
TURN SIGNAL/TAIL LAMP...............8L-9
BULB REPLACEMENT, FRONT PARK/
TURN SIGNAL LAMP
...................8L-8
BULB REPLACEMENT, HEADLAMP
..........8L-3
BULB REPLACEMENT, INSTRUMENT
CLUSTER
...........................8E-19
BULB REPLACEMENT, SIDE MARKER
LAMP
...............................8L-7
BULB REPLACEMENT, UNDERHOOD
LAMP
..............................8L-18
BULB REPLACEMENTÐYJ VEHICLES,
HARDTOP DOME/CARGO LAMP
.........8L-20
BULB/ELEMENT REPLACEMENT, FOG
LAMP
..............................8L-13
BUMPER, FRONT
..................13-3,13-14
BUMPER, LIFTGATE LICENSE PLATE
SCREW ANCHOR
.....................23-72
BUMPER, REAR
...................13-6,13-18
BUMPER, REAR JOUNCE
................13-18
BUMPERÐXJ VEHICLES, REAR
SEATBACK LATCH STRIKER
...........23-111BUMPERS AND FRAME ATTACHED
COMPONENTS, YJ....................13-14
BUMPERS, FUEL FILLER DOOR...........23-31
BUMPERS, XJ.........................13-3
BUSHING AND PISTON CLEARANCE, AW-
4 ................................21-326
BUSHING REPLACEMENT, AXLE.......2-11,2-32
BUSHING REPLACEMENT, LEAF SPRING
EYE; FRONT SUSPENSION AND AXLE.....2-15
BUSHING REPLACEMENT, LEAF SPRING
EYE; REAR SUSPENSION AND AXLES . . . 3-4,3-6
BUZZER SYSTEM, CHIME/WARNING........8A-1
CABLE, ACCELERATOR PEDAL AND
THROTTLE.....................14-16,14-54
CABLE ADJUSTMENT, PARK INTERLOCK . . . 21-186
CABLE ADJUSTMENT, SHIFT............21-186
CABLE ADJUSTMENT, TRANSMISSION
THROTTLE....................21-98,21-185
CABLE ADJUSTMENT, TRANSMISSION
THROTTLE VALVE....................21-70
CABLE ADJUSTMENT (XJ), PARK
INTERLOCK.........................21-97
CABLE ADJUSTMENT (XJ), SHIFT.........21-97
CABLE REPLACEMENT, HEATER
CONTROL..........................24-30
CABLE REPLACEMENT, LATCH
RELEASE...........................23-10
CABLE REPLACEMENT, SERVO............8H-9
CABLE REPLACEMENT, TRANSMISSION
THROTTLE.........................21-184
CABLE REPLACEMENT (XJ),
PARKING BRAKE REAR.................5-62
CABLE REPLACEMENT (YJ), PARKING
BRAKE FRONT........................5-62
CABLE REPLACEMENT (YJ), PARKING
BRAKE REAR.........................5-63
CABLE RESISTANCE, SPARK PLUG........8D-18
CABLE TENSIONER REPLACEMENT (XJ),
PARKING BRAKE......................5-61
CABLE, THROTTLE.....................14-16
CABLEÐCONSOLE SHIFT AUTOMATIC,
PARK-LOCK.........................19-45
CABLES, DISTRIBUTOR CAP AND ROTOR,
IGNITION............................0-18
CABLES, SPARK PLUG SECONDARY . . 8D-17,8D-29
CABLES, VENT DOOR CONTROL..........24-39
CALIBRATION VALUES, GAUGE...........8E-22
CALIPER ASSEMBLY....................5-29
CALIPER CLEANING AND INSPECTION......5-28
CALIPER DISASSEMBLY..................5-27
CALIPER INSTALLATION..................5-30
CALIPER OPERATION AND WEAR
COMPENSATION......................5-24
CALIPER REMOVAL.....................5-27
CAMSHAFT........................9-29,9-69
CAMSHAFT PIN REPLACEMENT........9-31,9-71
CAMSHAFT POSITION SENSOR; FUEL
SYSTEM............................14-54
CAMSHAFT POSITION SENSOR;
IGNITION SYSTEMS..............8D-1,8D-20
CAMSHAFT POSITION SENSORÐPCM
INPUT.............................14-20
CAMSHAFT POSITION SENSOR TEST;
FUEL SYSTEM.......................14-43
CAMSHAFT POSITION SENSOR TEST;
IGNITION SYSTEMS...................8D-8
CANADA ONLY, DAYTIME RUNNING
LIGHTS............................8L-16
CANISTER, EVAP...................25-4,25-9
CAP AND ROTOR, IGNITION CABLES,
DISTRIBUTOR........................0-18
CAP, DISTRIBUTOR.....................8D-9
CAP, FUEL TANK FILLER TUBE; EMISSION
CONTROL SYSTEMS...............25-4,25-9
CAP, FUEL TANK FILLER TUBE; FUEL
SYSTEM............................14-12
CAP, RADIATOR PRESSURE...............7-20
CAPACITIES, COOLING SYSTEM...........7-38
CAPACITIES, FLUID......................0-4
CAPACITIES, FUEL TANK...........14-12,14-62
CAPACITY TEST, FUEL PUMP..............14-7
CAR REPLACEMENT, PITMAN SHAFT
SEALSÐIN
.........................19-21
CARDAN (CV), DOUBLE
.................16-10
CARDAN, SINGLE
.......................16-9
CARDAN U-JOINT, AXLE SHAFT
............2-25
JINDEX3
Description Group-Page Description Group-Page Description Group-Page

DRIVE GEAR, SPEED SENSOR ROTORÐ
SPEEDOMETER.....................21-183
DRIVE, GENERATOR REPLACEMENTÐ
LEFT HAND..........................8B-7
DRIVE, GENERATOR
REPLACEMENTÐRIGHT HAND...........8B-9
DRIVE PULLEY REPLACEMENT...........19-11
DRIVE (RHD), BELT TENSIONÐEXCEPT
RIGHT HAND.........................7-33
DRIVE (RHD), BELT TENSIONÐRIGHT
HAND...............................7-34
DRIVE SHAFTS.........................0-27
DRIVE VEHICLES, RIGHT HAND............23-1
DRIVE, WASHER PUMP REPLACEMENTÐ
LEFT HAND..........................8K-2
DRIVE, WASHER PUMP REPLACEMENTÐ
RIGHT HAND.........................8K-3
DRIVELINE SNAP; FRONT SUSPENSION
AND AXLE...........................2-17
DRIVELINE SNAP; REAR SUSPENSION
AND AXLES...........................3-8
DRIVELINE VIBRATION...................16-3
DRIVER SIDE..........................8R-2
DRIVERS DOOR POWER LOCK SWITCHÐ
2-DOOR LEFT HAND DRIVE.............8P-2
DRIVERS DOOR POWER LOCK SWITCHÐ
2-DOOR RIGHT HAND DRIVE............8P-3
DRIVERS DOOR POWER LOCK SWITCHÐ
4-DOOR.............................8P-4
DRIVERS DOOR POWER WINDOW
SWITCHÐ2-DOOR LEFT HAND DRIVE.....8S-6
DRIVERS DOOR POWER WINDOW
SWITCHÐ2-DOOR RIGHT HAND DRIVE....8S-7
DRIVERS DOOR POWER WINDOW
SWITCHÐ4-DOOR....................8S-5
DRIVETRAIN...........................0-22
DRL MODULE REPLACEMENT............8L-16
DRUM BRAKE ADJUSTMENT..............5-35
DRUM BRAKES........................5-34
DRUM BRAKESHOE INSTALLATION.........5-34
DRUM BRAKESHOE REMOVAL.............5-34
DRUM REFINISHING, BRAKE..............5-37
DRUMÐREAR SUPPORT OVERHAUL,
OVERRUNNING CLUTCHÐLOW-
REVERSE..........................21-118
DUCT, DEFROSTER NOZZLE..............24-40
DUCT, FRESH AIR INTAKE...............24-41
DUCT REPLACEMENT, DEFROSTER........24-29
DUCTS/HOSES/TUBING, RUBBER AND
PLASTIC............................0-19
ECU DIAGNOSIS.........................5-4
ECU OPERATION.......................5-46
ECU REPLACEMENTÐXJ.................5-53
ECU REPLACEMENTÐYJ.................5-53
EDGE GUARD/EDGE PROTECTOR STRIP,
DOOR.............................23-61
ELECTRICAL CIRCUITS, ABS SYSTEM
WIRING..............................5-4
ELECTRICAL CONTROL, FUEL PUMP........14-5
ELECTRICAL TESTS AT POWERTRAIN
CONTROL MODULE...................8H-6
ELECTRICAL TESTS AT SERVO............8H-5
ELECTRICAL TESTS, VEHICLE SPEED
CONTROL SYSTEM....................8H-5
ELECTRONIC CONTROL UNIT (ECU)........5-41
ELEMENT, ENGINE AIR CLEANER FILTER....0-16
ELEMENT TEST, OXYGEN SENSOR (O2S)
HEATING...........................14-45
EMISSION CONTROL INFORMATION
(VECI) LABEL, VEHICLE.................25-1
EMISSION CONTROLS, EVAPORATIVE.......25-4
EMISSION CONTROLS, EXHAUST..........25-7
EMR LAMPÐPCM OUTPUT..............14-24
END PLUG, HOUSING...................19-26
ENGINE ACCESSORY DRIVE BELTS.........7-31
ENGINE AIR CLEANER FILTER ELEMENT.....0-16
ENGINE AND TRANSMISSION/TRANSFER
CASE IDENTIFICATION..............INTRO.-3
ENGINE ASSEMBLY (SHORT BLOCK),
SERVICE.............................9-4
ENGINE ASSEMBLYÐXJ VEHICLES;
ENGINES
........................9-14,9-54
ENGINE ASSEMBLYÐYJ VEHICLES;
ENGINES
........................9-16,9-57
ENGINE BLOCK HEATER
..................7-37
ENGINE BREAK-IN
......................0-13ENGINE COOLANT TEMPERATURE
SENSOR; FUEL SYSTEM...............14-55
ENGINE COOLANT TEMPERATURE
SENSOR; IGNITION SYSTEMS......8D-4,8D-22
ENGINE COOLANT TEMPERATURE
SENSORÐPCM INPUT................14-21
ENGINE COOLANT TEMPERATURE
SENSOR TEST; FUEL SYSTEM..........14-43
ENGINE COOLANT TEMPERATURE
SENSOR TEST; IGNITION SYSTEMS......8D-12
ENGINE CYLINDER HEAD.............9-19,9-60
ENGINE CYLINDER HEAD COVER......9-18,9-59
ENGINE CYLINDER HEAD GASKET
FAILURE DIAGNOSIS....................9-5
ENGINE DAMPER.......................9-13
ENGINE DIAGNOSIS......................9-5
ENGINE, ENGINE EXHAUST MANIFOLDÐ
2.5L................................11-7
ENGINE, ENGINE EXHAUST MANIFOLDÐ
4.0L................................11-7
ENGINE, ENGINE FIRING ORDERÐ2.5L....8D-33
ENGINE, ENGINE FIRING ORDERÐ4.0L....8D-33
ENGINE EXHAUST MANIFOLDÐ2.5L
ENGINE.............................11-7
ENGINE EXHAUST MANIFOLDÐ4.0L
ENGINE.............................11-7
ENGINE FIRING ORDERÐ2.5L ENGINE.....8D-33
ENGINE FIRING ORDERÐ4.0L ENGINE.....8D-33
ENGINE FRONT SUPPORT CUSHION.......13-15
ENGINE, INTAKE MANIFOLDÐ2.5L.........11-8
ENGINE, INTAKE MANIFOLDÐ4.0L.........11-9
ENGINE MAINTENANCE..................0-13
ENGINE MOUNTÐREAR.............9-12,9-52
ENGINE MOUNTSÐFRONT...........9-10,9-51
ENGINE OIL...........................0-13
ENGINE OIL CHANGE AND FILTER
REPLACEMENT.......................0-15
ENGINE OIL FILTER.....................0-14
ENGINE ONLY, POWER STEERING
PRESSURE SWITCHÐ2.5L.............14-58
ENGINE PERFORMANCE...................9-2
ENGINE SERVICE PROCEDURES, 2.5L........9-9
ENGINE SERVICE PROCEDURES, 4.0L.......9-50
ENGINE SPECIFICATIONS....9-47,9-87,9-48,9-49,
9-88,9-89
ENGINE STARTER MOTOR SERVICE
PROCEDURES........................8B-4
ENGINE STARTER MOTOR TEST
PROCEDURES ON VEHICLE.............8A-9
ENGINE SUPPORTS.....................0-20
ENGINE, VACUUM ROUTING
SCHEMATICÐ2.5L 4 CYLINDER..........25-2
ENGINE, VACUUM ROUTING
SCHEMATICÐ4.0L 6 CYLINDER..........25-3
ENGINES, 2.5L........................8B-11
ENGINES, 4.0L........................8B-11
ENGINES, CONDENSERÐ4.0L............24-32
ENGINES, CONDENSER/RECEIVER
DRIERÐ2.5L........................24-31
ENGINES, FUEL USAGE STATEMENTÐ
GAS................................0-17
ENGINES, RECEIVER DRIERÐ4.0L........24-32
ENTRY, KEYLESS.......................8P-8
ENTRY SYSTEM SERVICE INFORMATION,
ILLUMINATED.......................8L-20
ENTRY SYSTEM TROUBLE DIAGNOSIS,
ILLUMINATED..................8L-21,8L-22
EQUIVALENT VALUES, CONVERSION
FORMULAS......................INTRO.-8
EVACUATION, SYSTEM...................24-4
EVAP CANISTER....................25-4,25-9
EVAP (EVAPORATION) CONTROL SYSTEM
....25-4
EVAPORATIVE EMISSION CONTROLS
.......25-4
EVAPORATOR AND HOUSING
.............24-42
EVAPORATOR COIL
....................24-34
EVAPORATOR/BLOWER HOUSING
.........24-33
EXHAUST EMISSION CONTROLS
...........25-7
EXHAUST GRILLEÐXJ VEHICLES, AIR
.....23-30
EXHAUST HEAT SHIELDS
.................11-1
EXHAUST MANIFOLDÐ2.5L ENGINE,
ENGINE
.............................11-7
EXHAUST MANIFOLDÐ4.0L ENGINE,
ENGINE
.............................11-7
EXHAUST PIPEÐXJ VEHICLES
............11-3
EXHAUST PIPEÐYJ VEHICLES
............11-4EXHAUST SYSTEM; EXHAUST SYSTEM
AND INTAKE MANIFOLD................11-1
EXHAUST SYSTEM; LUBRICATION AND
MAINTENANCE.......................0-20
EXHAUST SYSTEM DIAGNOSIS............11-2
EXHAUST TAILPIPEÐXJ VEHICLES,
MUFFLER............................11-5
EXHAUST TAILPIPEÐYJ VEHICLES,
MUFFLER............................11-6
EXPANSION (H) VALVE.............24-35,24-43
EXTENDED IDLE SWITCHÐPCM INPUT....14-21
EXTENDED IDLE SWITCH TEST...........14-45
EXTENSION PANELÐYJ RENEGADE
VEHICLES, FRONT FENDER............23-149
EXTENSION PANELÐYJ RENEGADE
VEHICLES, REAR QUARTER...........23-151
EXTENSION PANELÐYJ RENEGADE
VEHICLES, ROCKER.................23-150
EXTENSION PANELS AND FASCIASÐYJ
RENEGADE VEHICLES, BODY..........23-147
EXTENSIONÐXJ VEHICLES, QUARTER
TRIM PANEL.......................23-115
EXTERIOR BODY COLORS..............23-204
EXTERIOR COMPONENTS..........23-3,23-134
EXTERIOR LAMPS......................8L-1
EXTERIOR LAMPS, XJ..................8L-23
EXTERIOR LAMPS, YJ..................8L-23
EXTERIOR MOULDINGS, DOOR WINDOW . . . 23-61
EXTERIOR NAMEPLATES................23-30
EXTERIOR NAMEPLATES (ADHESIVE-
BACKED)..........................23-158
EXTERIOR PAINT CODES, XJ............23-205
EXTERIOR PAINT CODES, YJ............23-206
EXTERNAL HANDLE, DOOR..............23-55
EXTERNAL MIRRORS...................23-31
EXTERNAL RELEASE HANDLE, FULL-
METAL DOOR LATCH.................23-178
EXTERNAL SPARE/WHEEL TIRE CARRIER . . 23-172
EYE BUSHING REPLACEMENT, LEAF
SPRING; FRONT SUSPENSION
AND AXLE...........................2-15
EYE BUSHING REPLACEMENT, LEAF
SPRING; REAR SUSPENSION
AND AXLES........................3-4,3-6
FAILURE DIAGNOSIS, ENGINE CYLINDER
HEAD GASKET.........................9-5
FAN RELAYÐPCM OUTPUT, RADIATOR.....14-26
FANS, COOLING SYSTEM.................7-26
FASCIA AND SKID PLATEÐYJ
RENEGADE VEHICLES, FRONT.........23-148
FASCIA AND SKID PLATEÐYJ
RENEGADE VEHICLES, REAR..........23-152
FASCIASÐYJ RENEGADE VEHICLES,
BODY EXTENSION PANELS............23-147
FAULT DIAGNOSIS, ABS................5-4,5-6
FEED CIRCUIT TESTS - (VOLTAGE DROP
METHOD), STARTER...................8A-9
FENDER EXTENSION PANELÐYJ
RENEGADE VEHICLES, FRONT.........23-149
FENDER FLARE.......................23-144
FENDER, FRONT.......................23-14
FENDER INNER SPLASH SHIELDS........23-147
FENDER SPLASH APRONS..............23-147
FENDERS...........................23-141
FIELDÐPCM OUTPUT, GENERATOR.......14-25
FILL LEVEL, TRANSFER CASE...........21-294
FILLER DOOR BUMPERS, FUEL...........23-31
FILLER HOSE SPLASH SHIELDÐXJ
VEHICLES, FUEL.....................23-86
FILLER NOZZLE/TUBE, FUEL
.............23-30
FILLER PROTECTOR/NOZZLE, FUEL
.......23-158
FILLER TUBE CAP, FUEL TANK;
EMISSION CONTROL SYSTEMS
......25-4,25-9
FILLER TUBE CAP, FUEL TANK; FUEL
SYSTEM
............................14-12
FILLER TUBE, NO-LEAD FUEL TANK
.......14-12
FILTER, AIR; EMISSION CONTROL
SYSTEMS
...........................25-9
FILTER, AIR; FUEL SYSTEM
..............14-54
FILTER BRACKET, FUEL
.................23-86
FILTER ELEMENT, ENGINE AIR CLEANER
....0-16
FILTER, ENGINE OIL
.....................0-14
FILTER, FUEL
.....................14-8,14-55
FILTER REPLACEMENT, ENGINE
OIL CHANGE
.........................0-15
8 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

FILTER REPLACEMENT, OIL.............21-100
FILTER SHIELD AND BRACKET, FUEL.......13-17
FINAL ASSEMBLY; FRONT SUSPENSION
AND AXLE...........................2-44
FINAL ASSEMBLY; REAR SUSPENSION
AND AXLES..........................3-26
FIRING ORDERÐ2.5L ENGINE, ENGINE....8D-33
FIRING ORDERÐ4.0L ENGINE, ENGINE....8D-33
FIRST GEAR (1) POSITION, HYDRAULIC
FLOW IN MANUAL...................21-94
FIRST GEAR, HYDRAULIC FLOW IN D
RANGE.............................21-87
FIRST-REVERSE BRAKE PISTON AND
TRANSMISSION CASE OVERHAUL......21-237
FIRST, SYMPTOM AND ACTIONÐSEE
PRELIMINARY CHECKS..................7-6
FIRSTÐTHIRDÐREVERSE GEAR
COMPONENTS......................21-159
FITTING CHART, CONNECTING ROD
BEARING........................9-36,9-76
FITTING CHART, MAIN BEARING.......9-43,9-83
FITTING O-RING SEAL, FLOW CONTROL
VALVE .............................19-12
FITTINGS, QUICK-CONNECT..........14-9,14-59
FITTINGS, SERVICING TRANSMISSION
COOLER LINES.....................21-106
FITTINGS, TRANSMISSION COOLER LINE . . 21-187
FIXED GLASS WATER LEAK DETECTION
AND REPAIR ..................23-83,23-189
FIXED WINDOW GLASS...........23-73,23-183
FIXED WINDOW GLASS, REAR DOOR......23-53
FLARE, FENDER......................23-144
FLARES AND LINERS, REAR
WHEELHOUSE.......................23-18
FLASHER, TURN SIGNALS AND HAZARD
WARNING...........................8A-1
FLOOR BRACKETSÐXJ VEHICLES,
SPARE TIRE/WHEEL HOLDDOWN.......23-128
FLOOR CONSOLEÐXJ VEHICLES, FULL . . . 23-125
FLOOR CONSOLES....................23-197
FLOOR MATS, CARPETS................23-129
FLOW CONTROL VALVE FITTING O-RING
SEAL..............................19-12
FLOW DURING FULL THROTTLE 3-2
DOWNSHIFT, HYDRAULIC..............21-92
FLOW DURING PART THROTTLE 3-2
DOWNSHIFT, HYDRAULIC..............21-91
FLOW IN D RANGE FIRST GEAR,
HYDRAULIC.........................21-87
FLOW IN D RANGE SECOND GEAR,
HYDRAULIC.........................21-88
FLOW IN D RANGE THIRD GEAR,
HYDRAULIC.........................21-89
FLOW IN MANUAL FIRST GEAR
(1) POSITION, HYDRAULIC.............21-94
FLOW IN MANUAL SECOND (2) RANGE,
HYDRAULIC.........................21-93
FLOW IN PARK AND NEUTRAL,
HYDRAULIC.........................21-86
FLOW IN REVERSE, HYDRAULIC..........21-95
FLOW IN THIRD GEAR (CONVERTER
CLUTCH ENGAGED), HYDRAULIC........21-90
FLOW TESTING, TRANSMISSION
COOLER...........................21-106
FLUID AND LEVELÐBRAKELINES
AND HOSES, BRAKE BLEEDINGÐ
BRAKE..............................5-13
FLUID CAPACITIES.......................0-4
FLUID, CLUTCH LINKAGE
..................6-1
FLUID CONTAMINATION, BRAKE
...........5-13
FLUID, IMPORTANCE OF CLEAN BRAKE
.....5-48
FLUID LEVEL AND CONDITION
...........21-69
FLUID LEVEL AND CONDITION,
CHECKING
....................21-96,21-173
FLUID LEVEL, BRAKE
....................5-13
FLUID LEVEL, CLUTCH
...................6-14
FLUID LEVEL, CORRECT
.................5-48
FLUID, RECOMMENDED
............21-66,21-96
FLUID, RECOMMENDED BRAKE; BRAKES
....5-13,
5-48
FLUID TUBE RETAINER CLIP, FUEL AND
BRAKE; BODY COMPONENTSÐXJ
VEHICLES
..........................23-86
FLUID TUBE RETAINER CLIP, FUEL
AND BRAKE; FRAME AND BUMPERS
.....13-16FLUID/LUBRICANTS/CLEANING
SOLVENTS, BRAKE.....................5-1
FLUSHING, COOLING SYSTEM CLEANING/
REVERSE............................7-17
FLUSHING, TRANSMISSION COOLER
REVERSE..........................21-105
FLYWHEEL SERVICE.....................6-15
FOG LAMP BEAM ADJUSTMENT..........8L-12
FOG LAMP BULB/ELEMENT
REPLACEMENT......................8L-13
FOG LAMP REPLACEMENT..............8L-15
FOG LAMP SERVICE INFORMATION........8L-12
FOG LAMP SWITCH REPLACEMENT.......8L-14
FOG LAMP TROUBLE DIAGNOSIS.........8L-12
FOG LAMPÐYJ RENEGADE VEHICLES....23-150
FORM-IN-PLACE GASKETS.................9-1
FORMULAS AND EQUIVALENT VALUES,
CONVERSION.....................INTRO.-8
FORWARD CLUTCH OVERHAUL..........21-223
FOURTH GEAR OVERDRIVE COMPONENTS . . 21-158
FRAME ALIGNMENT....................13-10
FRAME, BUCKET SEATBACK COVER......23-100
FRAME CROSSMEMBER COVER..........13-14
FRAME INSPECTION/MEASUREMENTS.....13-10
FRAME REPAIR SERVICE................13-13
FRAME WEATHERSTRIP SEAL,
WINDSHIELD.......................23-185
FRAME, WINDSHIELD.................23-184
FRAME, YJ............................13-8
FRESH AIR DOOR VACUUM MOTOR.......24-41
FRESH AIR INTAKE DUCT...............24-41
FRESH AIR VENTILATION................24-39
FRONT AND REAR AXLES................0-26
FRONT AXLE, MODEL 30.................2-46
FRONT BAND ADJUSTMENT.............21-99
FRONT BUCKET SEATS..................23-97
FRONT BUMPER...................13-3,13-14
FRONT CABLE REPLACEMENT (YJ),
PARKING BRAKE......................5-62
FRONT CARPET/MATÐXJ VEHICLES......23-129
FRONT CLUTCH OVERHAUL.............21-125
FRONT DOOR SPACER BLOCKSÐTWO-
DOOR VEHICLES.....................23-60
FRONT DOOR VENT WINDOW............23-50
FRONT DOOR WINDOW GLASS...........23-49
FRONT DOOR WINDOW GLASS
REGULATOR........................23-48
FRONT DRIVE AXLE......................2-3
FRONT FASCIA AND SKID PLATEÐYJ
RENEGADE VEHICLES................23-148
FRONT FENDER.......................23-14
FRONT FENDER EXTENSION PANELÐYJ
RENEGADE VEHICLES................23-149
FRONT INNER SCUFF PLATE/COWL SIDE
TRIM PANELÐXJ VEHICLES...........23-114
FRONT PARK/TURN SIGNAL LAMP BULB
REPLACEMENT.......................8L-8
FRONT PLANETARY GEAR OVERHAUL.....21-228
FRONT SERVO AND BAND OVERHAUL....21-136
FRONT SHOULDER BELT/BUCKLEÐXJ
VEHICLES.........................23-119
FRONT SHOULDER BELTS..............23-196
FRONT SKID PLATE....................23-84
FRONT SUPPORT CUSHION, ENGINE.......13-15
FRONT SUSPENSION.....................2-1
FRONT SUSPENSION COMPONENTS, XJ.....2-47
FRONT SUSPENSION COMPONENTS, YJ.....2-47
FRONT SUSPENSION, XJ.................2-10
FRONT SUSPENSION, YJ.................2-13
FRONT TOW HOOKS
....................13-5
FRONT WHEEL ALIGNMENT
................2-5
FRONT WHEEL BEARINGS
................0-31
FRONT WHEEL SENSOR INSTALLATION
.....5-49
FRONT WHEEL SENSOR REMOVAL
.........5-49
FRONT WIPER ARM AND PIVOT
ASSEMBLY REPLACEMENT
..............8K-9
FRONT WIPER ARM REPLACEMENT
........8K-8
FRONT WIPER BLADE REPLACEMENT
......8K-8
FRONT WIPER MOTOR
.................8K-10
FRONT WIPERS/WASHERS
...............8K-1
FRONT WIPERS/WASHERS GENERAL
INFORMATION
........................8K-8
FUEL AND BRAKE FLUID TUBE RETAINER
CLIP; BODY COMPONENTSÐXJ
VEHICLES
..........................23-86FUEL AND BRAKE FLUID TUBE
RETAINER CLIP; FRAME AND BUMPERS . . . 13-16
FUEL DELIVERY SYSTEM.................14-2
FUEL FILLER DOOR BUMPERS...........23-31
FUEL FILLER HOSE SPLASH SHIELDÐXJ
VEHICLES..........................23-86
FUEL FILLER NOZZLE/TUBE..............23-30
FUEL FILLER PROTECTOR/NOZZLE.......23-158
FUEL FILTER......................14-8,14-55
FUEL FILTER BRACKET..................23-86
FUEL FILTER SHIELD AND BRACKET.......13-17
FUEL GAUGE..........................8E-2
FUEL GAUGE INOPERATIVE...............8E-3
FUEL GAUGE SENDING UNIT.............14-15
FUEL INJECTION (MFI)ÐCOMPONENT
DESCRIPTION/SYSTEM OPERATION,
MULTI-PORT........................14-17
FUEL INJECTION (MFI)ÐCOMPONENT
REMOVAL/INSTALLATION, MULTI-PORT . . . 14-54
FUEL INJECTION (MFI)ÐGENERAL
DIAGNOSIS, MULTI-PORT..............14-32
FUEL INJECTOR.......................14-55
FUEL INJECTORSÐPCM OUTPUT.........14-25
FUEL PRESSURE LEAK DOWN TEST........14-7
FUEL PRESSURE REGULATOR............14-30
FUEL PRESSURE RELEASE PROCEDURE.....14-5
FUEL PUMP CAPACITY TEST..............14-7
FUEL PUMP ELECTRICAL CONTROL........14-5
FUEL PUMP MODULE..............14-2,14-56
FUEL PUMP RELAY....................14-56
FUEL PUMP RELAYÐPCM OUTPUT.......14-25
FUEL PUMP RELAY TESTING.............14-44
FUEL RAIL...........................14-30
FUEL RAIL ASSEMBLY..................14-56
FUEL REQUIREMENTS....................0-2
FUEL SYSTEM........................14-62
FUEL SYSTEM PRESSURE RELEASE
PROCEDURE........................14-56
FUEL SYSTEM PRESSURE TEST......14-5,14-48
FUEL TANK...........................14-12
FUEL TANK CAPACITIES............14-12,14-62
FUEL TANK FILLER TUBE CAP;
EMISSION CONTROL SYSTEMS......25-4,25-9
FUEL TANK FILLER TUBE CAP; FUEL
SYSTEM............................14-12
FUEL TANK FILLER TUBE, NO-LEAD.......14-12
FUEL TANK PRESSURE RELIEF/
ROLLOVER VALVE...............14-15,14-56
FUEL TANK SKID PLATE; BODY
COMPONENTSÐXJ VEHICLES..........23-84
FUEL TANK SKID PLATE; FRAME AND
BUMPERS..........................13-16
FUEL TANK SUPPORT STRAP............23-86
FUEL TANKS.....................14-12,14-56
FUEL TUBES/LINES/HOSES AND CLAMPS . . . 14-9,
14-56
FUEL USAGE STATEMENT................14-1
FUEL USAGE STATEMENTÐGAS
ENGINES............................0-17
FUEL WARNING INOPERATIVE, LOW........8E-4
FUEL WARNING LAMP, LOW..............8E-2
FULL FLOOR CONSOLEÐXJ VEHICLES....23-125
FULL-METAL DOOR ASSIST HANDLE.....23-175
FULL-METAL DOOR HINGES............23-179
FULL-METAL DOOR KEY LOCK
CYLINDER.........................23-178
FULL-METAL DOOR LATCH.............23-179
FULL-METAL DOOR LATCH EXTERNAL
RELEASE HANDLE...................23-178
FULL-METAL DOOR LATCH INSIDE
RELEASE AND LOCK HANDLE..........23-175
FULL-METAL DOOR SERVICE............23-181
FULL-METAL DOOR TRIM PANEL........23-175
FULL-METAL DOOR VENT WINDOW
GLASS............................23-177
FULL-METAL DOOR WATERDAM.........23-176
FULL-METAL DOOR WEATHERSTRIP
SEALS............................23-180
FULL-METAL DOOR WINDOW GLASS.....23-178
FULL-METAL DOOR WINDOW GLASS
REGULATOR
.......................23-177
FULL-METAL DOOR WINDOW GLASS
REGULATOR HANDLE
................23-175
FUNCTION TROUBLE DIAGNOSISÐXJ
VEHICLES, HEADLAMP DELAY
..........8L-16
FUSE CHARTS AND RELAY BANKS
.........8W-8
JINDEX9
Description Group-Page Description Group-Page Description Group-Page

MODES OF OPERATION, OPEN LOOP/
CLOSED LOOP.......................14-27
MODULE, ELECTRICAL TESTS
AT POWERTRAIN CONTROL.............8H-6
MODULE, FUEL PUMP..............14-2,14-56
MODULE, INTERMITTENT WIPER..........8K-5
MODULE (PCM) 60-WAY CONNECTOR,
POWERTRAIN CONTROL...............14-38
MODULE (PCM), POWERTRAIN
CONTROL; EMISSION CONTROL
SYSTEMS...........................25-9
MODULE (PCM), POWERTRAIN CONTROL;
FUEL SYSTEM..................14-18,14-58
MODULE (PCM), POWERTRAIN CONTROL;
IGNITION SYSTEMS.........8D-6,8D-15,8D-28
MODULE REPLACEMENT, DRL............8L-16
MODULE REPLACEMENTÐXJ VEHICLES,
HEADLAMP DELAY...................8L-16
MODULE (TCM) SERVICE, TRANSMISSION
CONTROL.........................21-173
MODULEÐXJ VEHICLES, SENTINEL
HEADLAMP DELAY...................8L-15
MOTOR, A/C BLOWER..................24-43
MOTOR DIAGNOSIS, DISCONNECT AXLE/
SHIFT...............................2-27
MOTOR, FRESH AIR DOOR VACUUM.......24-41
MOTOR, FRONT WIPER.................8K-10
MOTOR (HEATING), BLOWER............24-40
MOTOR, IDLE AIR CONTROL (IAC)........14-56
MOTOR NOISE DIAGNOSIS, 2.5L
STARTER...........................8A-13
MOTORÐPCM OUTPUT, IDLE AIR
CONTROL (IAC)......................14-25
MOTOR RELAY TEST, STARTER...........14-48
MOTOR REMOVAL/INSTALLATION, 2.5L
STARTER............................8B-5
MOTOR REMOVAL/INSTALLATION,
4.0L STARTER........................8B-6
MOTOR REPLACEMENT, A/C
RECIRCULATING AIR DOOR VACUUM.....24-31
MOTOR REPLACEMENT, HEATER/
DEFROSTER/INSTRUMENT PANEL
OUTLET DOOR VACUUM...............24-30
MOTOR REPLACEMENT, POWER SEAT......8R-2
MOTOR REPLACEMENT, REAR WIPER.....8K-13
MOTOR RESISTORS REPLACEMENT,
BLOWER...........................24-35
MOTOR SERVICE PROCEDURES,
ENGINE STARTER.....................8B-4
MOTOR SPECIFICATIONS, 2.5L STARTER . . . 8B-11
MOTOR STALL TEST, ACTUATOR...........8P-6
MOTOR SWITCH REPLACEMENT,
BLOWER MOTOR/AIR DOOR............24-39
MOTOR TEST, IDLE AIR CONTROL........14-46
MOTOR TEST PROCEDURES ON
VEHICLE, ENGINE STARTER.............8A-9
MOTOR TORQUE SPECIFICATIONS,
STARTER...........................8B-11
MOTOR, WINDSHIELD WIPER.............8K-2
MOTOR/AIR DOOR MOTOR SWITCH
REPLACEMENT, BLOWER..............24-39
MOTOR/FAN REPLACEMENT, BLOWER.....24-26
MOULDING, BODY SIDE STEP...........23-145
MOULDING, WINDSHIELD REVEAL . . 23-73,23-183
MOULDING, WOODGRAIN...............23-19
MOULDINGÐXJ VEHICLES, DRIP RAIL.....23-29
MOULDINGÐXJ VEHICLES, WINDSHIELD
SIDE.............................23-114
MOULDING/CLADDING, BODY SIDE........23-19
MOULDINGS, DOOR WINDOW EXTERIOR . . . 23-61
MOUNTING, MATCH TIRES...............22-7
MOUNTÐREAR, ENGINE.............9-12,9-52
MOUNTSÐFRONT, ENGINE...........9-10,9-51
MUFFLER AND EXHAUST TAILPIPEÐXJ
VEHICLES...........................11-5
MUFFLER AND EXHAUST TAILPIPEÐ
YJ VEHICLES.........................11-6
MUFFLER AND TAILPIPE HEAT SHIELDS....13-17
MUFFLER/TAILPIPE HANGER BRACKET
.....13-16
MULTI-PORT FUEL INJECTION (MFI)Ð
COMPONENT DESCRIPTION/
SYSTEM OPERATION
..................14-17
MULTI-PORT FUEL INJECTION (MFI)Ð
COMPONENT REMOVAL/INSTALLATION
. . . 14-54
MULTI-PORT FUEL INJECTION (MFI)Ð
GENERAL DIAGNOSIS
.................14-32NAMEPLATES (ADHESIVE-BACKED),
EXTERIOR.........................23-158
NAMEPLATES, EXTERIOR................23-30
NEUTRAL, HYDRAULIC FLOW IN PARK.....21-86
NEUTRAL SWITCH, PARK...............14-58
NOISE DIAGNOSIS......................3-45
NOISE DIAGNOSIS, 2.5L STARTER MOTOR . . . 8A-13
NOISE DIAGNOSIS, RADIO................8F-2
NOISE, GEAR AND BEARING; FRONT
SUSPENSION AND AXLE................2-16
NOISE, GEAR AND BEARING; REAR
SUSPENSION AND AXLES................3-7
NOISE OR VIBRATION, TIRE..............22-4
NOISE/VIBRATION DIAGNOSIS, AXLE;
FRONT SUSPENSION AND AXLE..........2-16
NOISE/VIBRATION DIAGNOSIS, AXLE;
REAR SUSPENSION AND AXLES..........3-7
NO-LEAD FUEL TANK FILLER TUBE........14-12
NON-INTERMITTENT WINDSHIELD
WASHER, DIAGNOSING...............8K-12
NON-TILT STEERING COLUMN............19-50
NORMAL BRAKING MODE, ABS
OPERATION IN.......................5-43
NOTATION, METRIC SYSTEM..........INTRO.-8
NOTATIONÐSAE AND METRIC, THREAD . INTRO.-9
NOTATIONS, SPECIFICATION...........INTRO.-8
NOZZLE AND DUCT, DEFROSTER..........24-40
NOZZLE REPLACEMENT, WASHER.........8K-13
NOZZLE/TUBE, FUEL FILLER.............23-30
NP231 SERVICE DIAGNOSIS............21-274
NP231 TRANSFER CASE.........21-272,21-291
NP231 TRANSFER CASE, LEGEND FOR....21-292
NP231/NP242 TORQUE SPECIFICATIONS . . . 21-331
NP242 SERVICE DIAGNOSIS............21-295
NP242 TRANSFER CASE...............21-293
NP242 TRANSFER CASE, LEGEND FOR....21-319
NUMBER (VIN) DECODING, VEHICLE
IDENTIFICATION...................INTRO.-2
NUMBER (VIN) PLATE, VEHICLE
IDENTIFICATION...................INTRO.-1
NUT TIGHTENING, WHEEL............5-32,5-37
NUT, WHEEL LUG......................22-11
OFF DRAW (IOD) DIAGNOSIS, IGNITION.....8A-8
OIL CHANGE AND FILTER REPLACEMENT,
ENGINE.............................0-15
OIL COOLERS, TRANSMISSION............7-29
OIL, ENGINE...........................0-13
OIL FILTER, ENGINE.....................0-14
OIL FILTER REPLACEMENT.............21-100
OIL LEVEL, COMPRESSOR................24-6
OIL PAN ..........................9-32,9-72
OIL PRESSURE GAUGE..................8E-1
OIL PRESSURE GAUGE INOPERATIVE.......8E-3
OIL PRESSURE INDICATOR...............8E-1
OIL PRESSURE INDICATOR INOPERATIVE....8E-3
OIL PUMP........................9-33,9-73
OIL PUMP OVERHAUL...........21-122,21-206
OIL PUMP SEAL REPLACEMENT.........21-189
OIL PUMP WEAR LIMITS, AW-4.........21-325
OIL SEAL REPLACEMENT, INNER AXLE
SHAFT..............................2-33
OIL SEAL REPLACEMENT, TIMING CASE
COVER..........................9-26,9-67
OIL SEALS, REAR MAIN..............9-44,9-84
OIL SEALS, VALVE SPRINGS..........9-21,9-62
ON-BOARD DIAGNOSTIC SYSTEM,
USING.............................8A-19
ON-BOARD DIAGNOSTICS (OBD);
COOLING SYSTEM.....................7-4
ON-BOARD DIAGNOSTICS (OBD); FUEL
SYSTEM............................14-48
ON-BOARD DIAGNOSTICS (OBD);
IGNITION SYSTEMS..................8D-19
ONE GAUGE INOPERATIVE...............8E-22
ONE-WAY CLUTCH OVERHAUL, NO. 2.....21-234
ONE-WAY CLUTCH OVERHAUL, NO. 1.....21-229
OPEN CIRCUIT VOLTAGE, BATTERY.........8A-4
OPEN CIRCUIT VOLTAGE TEST, BATTERY....8A-3
OPEN LOOP/CLOSED LOOP MODES OF
OPERATION
.........................14-27
OPENING PANEL (GOP), GRILLE AND
GRILLE
.............................23-3
OPENING WEATHERSTRIP SEAL,
LIFTGATE
...........................23-70
OPENING WEATHERSTRIP SEALS,
DOOR WINDOW GLASS AND DOOR
......23-62OPERATING SOUND LEVELS...............5-3
OPERATING SPECIFICATIONS, PUMP.......19-3
OPERATION, ABS SYSTEM................5-39
OPERATION, A/C........................24-1
OPERATION, ACCELERATION SWITCH.......5-45
OPERATION AND APPLICATION CHARTS,
GEARTRAIN........................21-159
OPERATION AND WEAR COMPENSATION,
CALIPER............................5-24
OPERATION, ANTILOCK BRAKE
SYSTEM............................5-43
OPERATION; CHIME/BUZZER
WARNING SYSTEMS...................8U-1
OPERATION, CLUTCH.....................6-2
OPERATION, COMPONENT
IDENTIFICATION/SYSTEM...............8D-1
OPERATION, COMPONENTS.............21-157
OPERATION, ECU
.......................5-46
OPERATION, HCU PUMP AND PEDAL
TRAVEL SENSOR
......................5-44
OPERATION, HCU SOLENOID VALVE
........5-43
OPERATION, HEATER/DEFROSTER
.........24-37
OPERATION IN ANTILOCK BRAKING
MODE, ABS
..........................5-43
OPERATION IN NORMAL BRAKING MODE,
ABS
................................5-43
OPERATION, MULTI-PORT FUEL
INJECTION (MFI)ÐCOMPONENT
DESCRIPTION/SYSTEM
................14-17
OPERATION, OPEN LOOP/CLOSED LOOP
MODES OF
..........................14-27
OPERATION, PARKING BRAKE
.............5-56
OPERATION, POWER BRAKE BOOSTER
......5-22
OPERATION, POWER STEERING PUMPÐ
INITIAL
............................19-13
OPERATION; REAR SUSPENSION AND
AXLES
..............................3-44
OPERATION, SYSTEM
...................8P-9
OPERATION, WHEEL SPEED SENSOR
.......5-45
OPERATION/DIAGNOSIS
..................8U-1
OPERATIONAL CHECK (ROAD TEST)
........8H-7
OPERATIONAL CHECK WITH BATTERY
INDICATOR (BASE CLUSTER ONLY)
......8A-14
OPERATIONAL CHECK WITH VOLTMETER
. . . 8A-15
O-RING SEAL, FLOW CONTROL VALVE
FITTING
............................19-12
ORNAMENTATION, WHEEL
................22-6
OUTER SCUFF PLATESÐXJ VEHICLES
....23-118
OUTLET DOOR VACUUM MOTOR
REPLACEMENT, HEATER/DEFROSTER/
INSTRUMENT PANEL
..................24-30
OUTPUT, AIR CONDITIONING CLUTCH
RELAYÐPCM
.......................14-24
OUTPUT, AUTO SHUT DOWN (ASD)
RELAYÐPCM
.......................14-24
OUTPUT, DATA LINK CONNECTORÐPCM
. . . 14-24
OUTPUT, EMR LAMPÐPCM
..............14-24
OUTPUT, FUEL INJECTORSÐPCM
.........14-25
OUTPUT, FUEL PUMP RELAYÐPCM
.......14-25
OUTPUT, GENERATOR FIELDÐPCM
.......14-25
OUTPUT, GENERATOR LAMPÐPCM
.......14-25
OUTPUT, IDLE AIR CONTROL (IAC)
MOTORÐPCM
.......................14-25
OUTPUT, IGNITION COILÐPCM
...........14-26
OUTPUT, MALFUNCTION INDICATOR
LAMPÐPCM
........................14-26
OUTPUT, RADIATOR FAN RELAYÐPCM
.....14-26
OUTPUT, SCI TRANSMITÐPCM
...........14-26
OUTPUT SHAFT OVERHAUL, NO. 2 ONE-
WAY CLUTCH
......................21-234
OUTPUT, SHIFT INDICATORÐPCM
........14-26
OUTPUT, SPEED CONTROLÐPCM
.........14-27
OUTPUT, TACHOMETERÐPCM
...........14-27
OUTPUT, TORQUE CONVERTER CLUTCH
RELAYÐPCM
.......................14-27
OUTPUT VOLTAGE SPECIFICATIONS
.......8B-12
OVERDRIVE COMPONENTS, FOURTH
GEAR
.............................21-158
OVERDRIVE PLANETARY GEAR AND
CLUTCH OVERHAUL
.................21-209
OVERDRIVE SUPPORT OVERHAUL
.......21-216
JINDEX15
Description Group-Page Description Group-Page Description Group-Page