1994 CHEVROLET CAMARO lock

Downloaded from www.Manualslib.com manuals search engine Comfort Controls and Audio Systems
6. Turn the lower knob until the fifth and
sixth digits
of your code appear,
7. Press the lower knob. The clock
display will appear and the unit will
work. If
“LOC” shows, the numbers
did not match and the unit is still
locked.
How to Change Your Security Code
You can change your security code by
following these steps:
1. Using your old code, follow the
directions given under “Shutting
Off
the Theft-Deterrent Feature.”
2. Repeat directions of “Setting Your
Security Code” with your new
security code.
Understanding Radio Reception
FM Stereo
FM stereo will give you the best sound.
But
FM signals will reach only about
10 to 40 miles (16 to 65 km). And, tall
buildings or hills can interfere with
FM signals, causing the sound to come
and go.
I
AM
The range for most AM stations is greater
than for
FM, especially at night. The
longer range, however, can cause stations
to interfere with each other. AM can pick
up noise from things like storms and
power lines. Try reducing the treble to
reduce this noise if you ever get it.
AM Stereo
This means the Delco@ system can
receive C-QUAM@ stereo broadcasts.
Many
AM stations around the country use
C-QUAM@ to produce stereo, though
some do not. (C-QUAM@
is a registered
trademark of Motorola, Inc.) If your
Delco@ system can get C-QUAM@, your
“STEREO” light will come on when
you’re receiving it.
Care of Your Cassette Tape
Player
A tape player that is not cleaned regularly
can cause reduced sound quality, ruined
cassettes, or a damaged mechanism.
Cassette tapes should be stored in their
cases away from contaminants, direct
sunlight, and extreme heat. If they aren’t,
they may not operate properly or cause
failure of the tape player.
Your tape player should
be cleaned
regularly each month or after every
15
hours of use. If you notice a reduction in
sound quality, try a known good cassette
to see if the tape or the tape player
is at
fault. If this other cassette has no
. . .I20

Downloaded from www.Manualslib.com manuals search engine This is a mistake. Your brakes may not
have time to cool between hard stops.
Your brakes will wear out much faster if
you do a lot of heavy braking. If you keep
pace with the traffic and allow realistic
following distances, you will eliminate a
lot of unnecessary braking. That means
better braking and longer brake life.
If your engine ever stops while you’re
driving, brake normally but don’t pump
your brakes. If you
do, the pedal may
get harder to push down. If your engine
stops, you will still have some power
brake assist. But you will use
it when
you brake. Once the power assist is used
up, it may take longer to stop and the
brake pedal
will be harder to push.
inti-Lock Brakes (ABS)
tour Chevrolet has an advanced
klectronic braking system that
will help
- revent sludding.
ABS
INOP
?his light on the instrument panel will go
m when you start your vehicle.
Nhen you start your vehicle, or when yo1
)egin to drive away, you may hear a
nomentary motor or clicking noise. And
’ou may even notice that your brake
bedal moves a little while
this is going on
:his
is the ABS system testing itself. If
here’s a problem with the anti-lock brake
ystem, the anti-lock brake system
varning light will stay
on or flash.
;ee “Anti-Lock Brake System Warning
ight” in the Index.
1
127 ...

Downloaded from www.Manualslib.com manuals search engine Your Driving and the Road
Here’s how anti-lock works. Let’s say
the road is wet. You’re driving safely. Suddenly an animal jumps out
in front
You slam on the brakes. Here’s what
happens with ABS.
A computer senses that wheels are
slowing down. If one of the wheels is
about to stop rolling, the computer will
separately work the brakes at each front
wheel and at the rear wheels.
The anti-lock system can change the
brake pressure faster than any driver
could. The computer
is programmed to
make the most of available tire and road
conditions.
of you.
You can
steer around the obstacle while
braking hard.
As you brake, your computer keeps
receiving updates on wheel speed and
controls braking pressure accordingly.
Remember: Anti-lock doesn’t change the
time
you need to get your foot up to the
brake pedal.
If you get too close to the
vehicle in front of you,
you won’t have
time to apply your brakes if that vehicle
suddenly slows or stops. Always leave
enough room up ahead to stop,
even
though you have anti-lock brakes.
To Use Anti-Lock
Don’t pump the brakes. Just hold the
brake pedal down and let anti-lock
work for you. You may feel the system
working, or you may notice some noise, but this is normal. When your anti-lock
system
is adjusting brake pressure to help
avoid a braking skid, the
“LOW TRAC”
light will come
on. See “Low Traction
Light”
in the Index.
ASR (Acceleration Slip Regulation) System (Option:
LT1 VS Engine)
Your vehicle may have an ASR system
that limits wheel spin. This
is especially
useful in slippery road conditions. The
system operates only
if it senses that one
or both of the rear wheels are spinning or
beginning
to lose traction.
When this happens, the system works the
rear brakes and reduces engine power (by closing the throttle and managing spark)
to limit wheel spin.
The “LOW TRAC” light will come on
when your
ASR system is limiting wheel
spin. See “Low Traction Light” in the
Index. You may
feel the system working,
or you may notice some noise, but this is
normal.
The
ASR system may operate on dry
roads under some conditions, and you
may notice a reduction
in acceleration
when this happens.
This is normal and
doesn’t mean there’s a problem with
your
vehicle. Examples of these conditions
include a hard acceleration
in a turn, or
an abrupt upshift or downshift.
. . .I28

Downloaded from www.Manualslib.com manuals search engine ‘I i
If your vehicle is in cruise control when
the ASR system begins
to limit wheel
spin, the cruise control will automaticallq
disengage. When road conditions allow
you to safely use it again, you may
re-engage the cruise control. (See
“Cruise Control” in the Index.)
The “ASR” warning light will come on
when you tu-n the ASR system off. Whe~
the system is on, this light will come on
to let you know if there’s a problem with
your ASR system.
See “ASR System
Warning Light” in the Index.
When this warning light is on, the system
will not limit wheel spin. Adjust your
drjving accordingly.
ASR
The ASR system automatically comes on
whenever you start your vehicle.
To limit wheel spin, especially in
slippery road conditions, you should
always leave the system on. But you can
turn the ASR system
off if you ever need
to. (You should turn the system
off if
your vehicle ever gets stuck in sand,
mud, ice or snow.
See “Rocking Your
Vehicle” in the Index.)
To turn the system
off, press the button on
the console near the cigarette lighter. The
“ASIC” warning light will come on and
stay on. -If the ASR system is limiting
wheel spin when you press the button, the
system won’t turn off right away. It will
wait until there’s no longer a current need
to limit wheel spin. You
can turn the system back on at any
time by pressing the button again. The
*‘ASR’ warning light should go
off.
[f your car is equipped with P245/50ZR16
tires, the ASR system will automatically
turn
off at speeds above 108 mph (173
km/h). (The “ASR” warning light will
not come on.) When vehicle speed drops
below
103 mph (165 km/h), the system
will automatically turn on again.
Braking in Emergencies
Use your anti-lock braking system when
you need to. With anti-lock, you can
steer and brake
a1 the same time. In many
emergencies, steering can help you more
than even the very best braking.
129 ...

Downloaded from www.Manualslib.com manuals search engine to the left or right depending on the space
available.
An emergency like this requires close
attention and a quick decision. If you are
holding the steering wheel at the
recommended
9 and 3 o’clock positions,
you can turn it a
full 180 degrees very
quickly without removing either hand.
But you have to act fast, steer quickly,
and just as quickly straighten the wheel
once you have avoided the object.
The fact that such emergency situations
are always possible is a good reason to
practice defensive driving at all times and
wear safety belts properly.
Off-Road Recovery
You may find sometime that your right
wheels have dropped
off the edge of a
road onto the shoulder (A) while you’re
driving.
If the level of the shoulder is only slight11
below the pavement, recovery should be
fairly easy. Ease off the accelerator and
then, if there
is nothing in the way, steer
so that your vehicle straddles the edge of
the pavement. You can
turn the steering
wheel up to
1/4 turn (B) until the right
front tire contacts the pavement edge.
Then
turn your steering wheel to go
straight down the roadway.
Passing
The driver of a vehicle about to pass
another on a two-lane highway waits for
just the right moment, accelerates, moves
around the vehicle ahead, then goes back
into the right
lane again. A simple
maneuver?
Not necessarily! Passing another vehicle
on a two-lane highway is a potentially
dangerous move, since the passing
vehicle occupies the same lane as
oncoming traffic for several seconds. A
miscalculation, an error
in judgment, or a
brief surrender to frustration or anger can
suddenly put the passing driver face to
face with the worst of all traffic accidents
- the head-on collision.
So here are some tips for passing:
“Drive ahead.” Look down the road,
to the sides, and to crossroads for
situations that might affect your
passing patterns. If you have any
doubt whatsoever about making a
successful pass, wait for a better time.
Watch for traffic signs, pavement
markings, and lines. If you can see a
sign
up ahead that might indicate a
turn
or an intersection, delay your
pass. A broken center line usually
131.. .

Downloaded from www.Manualslib.com manuals search engine much throttle causes the driving wheels to
spin.
A cornering skid is best handled by
easing your foot
off the accelerator pedal.
If you have the ASR system, remember: It
helps avoid only the acceleration skid. If
you do not have traction control, or
if the
system is
off, then an acceleration skid is
also best handled by easing your foot
off
the accelerator pedal.
If your vehicle starts to slide, ease your
foot
off the accelerator pedal and quickly
steer the way you want the vehicle to go.
If you start steering quickly enough, your
vehicle may straighten out. Always be
ready for a second skid if it occurs.
Of course, traction is reduced when water,
snow, ice, gravel, or other material is on
the road. For safety, you’ll want to slow
down and adjust your driving
to these
conditions. It is important to slow down
on slippery surfaces because stopping distance will be longer and vehicle
control more limited. While
driving on a surface with reduced
traction, try
your best to avoid sudden
steering, acceleration,
or braking
(including engine bralung by shifting to a
lower gear). Any sudden changes could
cause the tires to slide. You may not
realize the surface is slippery until your
vehicle is skidding. Learn to recognize
warning clues
- such as enough water,
ice or packed snow on the road to make
a .“mirrored surface”
- and slow down
when you have any doubt.
Remember: Any anti-lock braking system
(ABS) helps avoid only the braking skid.
. ..
I
4
Driving at Night
\Tight driving is more dangerous than day
hiving. One reason is that some drivers
tre likely to be impaired
- by alcohol or
lrugs, with night vision problems, or by
atigue.
lere
are some tips on night driving.
Drive defensively.
Don’t drink and drive.
Adjust your inside rearview mirror to
reduce the glare from headlights
behind you.
Since you can’t see as well, you may
need to slow down and keep more
space between
you and other vehicles.
133 ...

Downloaded from www.Manualslib.com manuals search engine Slip Regulation (ASR) System” in the
Index.
If you don’t have the traction control
system, accelerate gently. Try not to break
the fragile traction. If you accelerate too
fast, the drive wheels will spin and polish
the surface under the tires even more.
Your anti-lock brakes improve your
ability to make a hard stop on a slippery
road. Even though you have the anti-lock
braking system, you’ll want to begin
stopping sooner
than you would on dry
pavement. See “Anti-Lock” in
the Index.
0
0
Allow greater following distance on
any slippery road.
Watch for slippery spots. The road
might be fine until you hit a spot that’s
covered with ice. On an otherwise
clear road, ice patches may appear
in
shaded areas where the sun can’t
reach: around clumps of trees, behind
buildings, or under bridges.
Sometimes the surface
of a curve or
an overpass may remain icy when the
surrounding roads are clear. If you see
a patch of ice ahead of you, brake
before you are on
it. Try not to brake
while you’re actually on the ice, and
avoid sudden steering maneuvers.
If You’re Caught in a Blizzard
If you are stopped by heavy snow, you
could be
in a serious situation. You should
probably stay with your vehicle unless
you know for sure that you are near help
and you can hike through
the snow. Here
are some things to do to summon help and
keep yourself and your passengers safe:
Turn on your hazard flashers. Tie a red
cloth to your vehicle to alert police that
you’ve been stopped by the snow. Put
on
extra clothing or wrap a blanket around
you. If you have no blankets or extra
clothing, make body insulators from
newspapers, burlap bags, rags, floor mats
- anything you can wrap around yourself
or tuck under your clothing to keep warm.
You can run the engine to keep warrn, but
be careful.
141 . I

Downloaded from www.Manualslib.com manuals search engine Trailer Brakes
If your trailer weighs more than 1,000
pounds (450 kg) loaded, then it needs its
own brakes
- and they must be adequate.
Be sure to read and follow the instructions
for the trailer brakes
so you’ll be able to
install, adjust and maintain them properly.
Because you have anti-lock brakes, do not
try to tap into your vehicle’s brake
system. If you do, both brake systems
won’t work well, or at all.
Driving with a Trailer
Towing a trailer requires a certain amount
of experience. Before setting out for the
open road, you’ll want to get to know
your rig. Acquaint yourself with the feel
of handling and braking with the added
weight of the trailer. And always keep in
mind that the vehicle you are driving is
now
a good deal longer and not nearly so
responsive as your vehicle is by itself.
Before you start, check the trailer hitch
and platform, safety chains, electrical
connector, lights, tires and mirror
adjustment. If the trailer has electric
brakes, start your vehicle and trailer
moving and then apply the trailer brake
controller by hand to be sure
the brakes are working.
This lets
you check your
electrical connection at the same time.
During your trip, check occasionally to be sure that the load is secure, and that
the
lights and any trailer brakes are still
working.
Following Distance
Stay at least twice as far behind the
vehicle ahead as you would when driving
your vehicle without a trailer. This can
help you avoid situations that require
heavy braking and sudden turns.
Passing
You’ll need more passing distance up
ahead when you’re towing a trailer. And,
because you’re a good deal longer, you’ll need to go much farther beyond the
passed vehicle before you can return
to
your lane.
Backing Up
Hold the bottom of the steering wheel
with one hand. Then, to move the trailer
to the left, just move that hand to the left.
To move the trailer to the right, move
your hand to the right. Always back up slowly
and, if possible, have someone
guide you.
Making Turns
When you’re turning with a trailer, make
wider turns than normal.
Do this so your
trailer won’t strike soft shoulders, curbs,
road signs, trees, or other objects. Avoid
jerky or sudden maneuvers. Signal well in
advance.
Turn Signals When Towing a Trailer
When you tow a trailer, your vehicle has
to have a different turn signal flasher and
extra wiring. The green arrows on your
instrument panel will flash whenever you
signal a turn or lane change. Properly
hooked up, the trailer lights will also
flash, telling other drivers you’re about to
turn, change lanes or stop.
When towing a trailer, the green arrows
Dn your instrument panel will flash for
turns even if the bulbs on the trailer are
burned out. Thus, you may think drivers
behind you
are seeing your signal when
they are not. It’s important to check
occasionally to be sure the trailer bulbs
are still working.
145. I