1994 CHEVROLET CAMARO display

Downloaded from www.Manualslib.com manuals search engine New Vehicle
“Break-In”
NOTICE:
Your modern Chevrolet doesn’t need
an elaborate “break-in.” But it will
perform better
in the long run if you
follow these guidelines:
Keep your speed at
55 mph (88
km/h) or less for the first 500
miles (804 km).
Don’t drive at any one speed
-
fast or slow - for the first 500
miles (804 km). Don’t make
full-throttle starts.
Avoid making hard stops for the
first
200 miles (322 km) or so.
During this time your new brake
linings aren’t yet broken
in. Hard
stops with new linings can mean
premature wear and earlier
replacement. Follow this
“breaking-in” guideline every
time
you get new brake linings.
D
I Ignition Switch
Vith the ignition key in the ignition
witch,
you can turn the switch to five
lositions:
KC (A): Position in which you can
lperate your electrical power accessories.
’ress
in the ignition switch as you turn
?e top
of it toward you.
,OCK (B): The only position in which
ou can remove the key. This locks your
teering wheel, ignition and automatic
7ansmission.
f you have an automatic transmission, the
znition switch can’t be turned to
LOCK” unless the shift lever is
in the
“P” (Park) position.
Off (C): Unlocks the steering wheel,
ignition and automatic transmission, but
does not send electrical power to any
accessories.
Use this position if your
vehicle must be pushed or towed.
A
warning tone will sound if you open the
driver’s door when the ignition
is in “Off’
and the key is
in the ignition.
Run (D): Position to which the switch
returns after
you start your engine and
release the switch. The switch stays
in the
“Run” position when the engine is
running.
But even when the engine is not
running,
you can use “Run” to operate
your electrical power accessories and to
display some instrument panel warning
and indicator lights.
Start (E): Starts the engine. When the
engine starts, release the key. The ignition
switch will return to “Run” for normal
driving.
Note that even if the engine is not
running, “ACC” and “Run’’ allow
you to
operate your electrical accessories, such
as the radio and ventilation fan.
55. .

Downloaded from www.Manualslib.com manuals search engine Trip Odometer
The trip odometer can tell you how far
your vehicle has been driven since you
last set the trip odometer to.zero.
To set the trip odometer to zero, press the
hob.
Tachometer
The tachometer displays the engine speed
in thousands
of revolutions per minute
(rpm).
NOTICE:
Do not operate the engine with the
tachometer in the red area, or engine
damage may occur.
Warning Lights, Gages
and Indicators
This section describes the warning lights
and gages that may be on your vehicle.
The pictures will help you locate them.
Warning lights and gages can signal that
something is wrong before it becomes
serious enough to cause an expensive
repair or replacement. Paying attention to
your warning lights and gages could also
save you or others from injury.
Warning lights go on when there may be
or is a problem with one of your vehicle’s
functions.
As you will see in the details
on the next few pages, some warning
lights come on briefly when you turn the
ignition key just to let you know they’re
working.
If you are familiar with this
section, you should not be alarmed when
this happens.
Gages can indicate when there may be
or
is a problem with one of your vehicle’s
functions. Often gages and warning lights
work together to let you know when
there’s a problem with your vehicle. When one
of the warning lights comes on
and stays
on when you are driving, or
when one of the gages shows there may
be a problem, check the section that tells
you what to do about it. Please follow the
manual’s advice. Waiting to do repairs
can be costly
- and even dangerous. So
please get to know your warning lights
and gages. They’re a big help.
93 ...

Downloaded from www.Manualslib.com manuals search engine I Setting the Clock
AM/FM Stereo with Cassette Tape
Player
1. Press “SET.”
2. Within five seconds, press and hold
“SEEK
V’’ until the correct hour
appears.
3. Press and hold “SEEK A’’ until the
correct minute appears.
Delco/Bose AM/FM Stereo with Compact Disc Player
1. Press “SET.”
2. Within five seconds, press and hold
“SCAN” until the correct hour
appears.
“SEEK ” until the correct minute
appears.
3. Press and hold “SEEK 4 ” or
I
/ VOL- BAL TREE
PROG-RCL A
1 TUNE- FADE BASS
AM-FMA
\
AMIFM Stereo with Cassette
Tape Player
To Play the Radio
Turn the upper knob to turn the system
on or off.
Volume
Turn the upper knob to adjust the
volume.
AM-FM
Press the lower knob to get AM or FM.
The lighted display shows your
selection.
Tune
Turn the lower knob to choose radio
stations.
Recall
Press the upper knob to recall the
station being played or the clock
display.
Seek
Press “SEEK 7’’ or “SEEK A’7 and
the radio
will tune to the next lower
or higher station and stay there.
113 ...

Downloaded from www.Manualslib.com manuals search engine Comfort Controls and Audio Systems
/- VOLUME TREB
PROG-RCL P
TUNE -3 FADE BASS
\
V SEEK P I 234 SET
[II] [OOOO]
AM-FM n
Scan
The scan function uses the same two
buttons as the seek function.
To
go to the next higher station and stay
there for a few seconds, press and hold
“SEEK
A’’ and then press “SEEK 7” for
an instant.
To go to the next lower station and stay
there for a few seconds, press and hold
“SEEK
7’’ and then press “SEEK A’’ for
an instant.
To stop the scan function, press either
“SEEK
A’’ or “SEEK v.”
Pushbuttons
The four pushbuttons let you return to
your favorite stations.
You can preset up
to 14 stations (7 AM and 7 FM).
To set the pushbuttons for up to eight
stations
(4 AM and 4 FM), just:
1. Tune in the station.
2. Press “SET.” (“SET” will appear on
the display for about five seconds.)
3. Within five seconds, press one of the
four pushbuttons. Whenever
you
press that button, the preset station
will return.
Repeat these steps for each pushbutton.
You can preset three mor e stations on
each band
by pressing a pair of buttons
next to each other at the same time. Just:
1. Tune in the station.
2. Press “SET.” (“SET” will appear on
3. Within five seconds, press two
the
display for about five seconds.)
pushbuttons next to each other at the
I1
same time. Whenever you press that
pair of buttons, the preset station wil
return.
Repeat these steps for each pair of
pushbuttons.
Setting the Tone
Bass: Slide the “BASS” levkfup to hear
more bass.
Treble: Slide the “TREB” lever up to
hear more treble.
If a station
is weak and noisy, move
“TREB” down to reduce the noise.
. . .114

Downloaded from www.Manualslib.com manuals search engine Comfort Controls and Audio Systems
[ VOLOBAL
POWER
1 TUNE 00 FADE
F
D
R
‘c AM-FM a
COMP RDM REV FWD SCAN PREV NEXT
AM!FM Stereo with Compact
Disc Player
To Play the Radio
Turn the upper knob to turn the system on
or off.
Volume
Turn the upper knob to adjust the volume.
AM-FM
Press the lower knob to get AM, FMl or
FM2.
. . . 116
Tune
Turn the lower knob to choose radio
stations.
Recall
Press “RCL” to reca .I1 the station being
played or the time.
Seek
Press “SEEK 4 ” or “SEEK ” to go to
the next lower
or higher station and stay
there.
Scan
Press “SCAN’ to hear each station for a
few seconds. When you want to stop
scanning, press “SCAN’ again or the
upper knob.
Pushbuttons
The five pushbuttons let you return to
your favorite stations.
To set the
pushbuttons for up to
15 stations (5 AM,
5 FMl and 5 FM2), just:
1. Press the lower knob to choose AM,
2. Tune in the station.
3. Press “SET.” (“SET” will appear on
the display for about five seconds.)
4. Within five seconds, press one of the
pushbuttons. Whenever you press that
button, the preset station
will return.
FMl or FM2.

Downloaded from www.Manualslib.com manuals search engine POWER
AM-FMrz
f ST-PL COMP RDM REV FWD SCAN PREV NEXT^
Setting the Tone
Bass: Press “BASS A ” or “BASS v ’’ to
hear more or less bass.
Treble: Press “TREB A ” or “TREB v ”
to hear more or less treble.
For the clearest sound, keep both of these
adjusted all the way up. If
a station is
weak and noisy, press “TREB
v ” to
reduce the noise.
Adjusting the Speakers
Balance:
Turn the balance control behind
the upper knob to move the sound
between the right and left speakers.
Fade: Turn the Fade control behind the
lower knob to move the sound between
the front and rear speakers.
The Delco/Bose premium speaker system
only includes three speakers. It does not
include speakers
in the panel behind the
grilles next to the rear seat.
To Play a Compact Disc
Before you begin, please note: don’t use
the mini-discs that are called “singles.”
They won’t eject.
Use full-size compact
discs.
With the audio system on, insert a disc
into the slot
with the label side up. “CD”
will appear on the display and track 1 wil
begin to play.
If the disc comes back out and “ERR”
appears on the display, it could be that:
The disc is upside down.
It is dirty, scratched, or wet.
0 There’s too much moisture in the air.
You are driving on a very rough road.
0 The temperature is too hot or too cold.
Recall
Press “RCL” to see what track is playing.
Press
it again within five seconds to see
how long
it has been playing.
The track number also appears when the
disc is inserted.

Downloaded from www.Manualslib.com manuals search engine Comfort Controls and Audio Systems
To Play the Next Selection
Press “NEXT” to hear the next track now
(instead of waiting until
the present track
is finished).
If you press and hold this button or press
it more than once, the disc will advance
further.
To Replay the Current Selection
Press “PREV” to hear a track again.
If you press and hold this button, or press
it more than once, the disc will return to
previous tracks.
Reverse
Press and hold “REV” to rapidly return to
a favorite passage. Release
it to play the
passage.
Fast Forward
Press and hold “FWD’ to quickly
advance within
a track. Release it to
resume playing.
Scan
Press “SCAN” to listen to each track for
about
10 seconds. Press “RDM” or
“SCAN” to stop the scanning.
Compression
Press “COMP’ to make loud and soft
passages more nearly equal
in volume.
Random
Press “RDM” to hear a random selection
of tracks.
To Stop the Disc Player
0
0
0
Turn the power off or turn the ignition
key off. The disc stays
in the player
and will resume playing at the point
where
it stopped.
Press “ST-PL” to stop playing the disc
and switch to radio. Press “ST-PL,” to
restart
the disc at the point where it
stopped.
Press “EJCT” to eject the disc and the
radio
will play. The disc will start
playing
at track 1 when you reinsert it.
Theft-Deterrent Feature
Delco-Loc I1 is a security feature for the
compact disc player.
It can be used or
ignored. If ignored, the system functions
normally. If
it is used, your system won’t
be usable
if it’s ever stolen.
Setting Your Security Code
The instructions below tell you how to
enter a security code into the system. If
your vehicle loses battery power for
any
reason, you must enter the security code
again before the system
will turn on.
1. Write down any six-digit number and
2. Turn the ignition switch to the “Acc”
3. Turn the audio system off.
4. Press and hold pushbuttons “1” and
keep
it in a
safe place.
or
“Run” position.
“4” together until “---” shows on the
display.
You are now ready to enter your security
code. Don’t wait more than
15 seconds
between steps.
. . .118

Downloaded from www.Manualslib.com manuals search engine 5. Press “SET” and “000” will appear
on the display.
~ 6. Press “SEEK 4 ” or “SEEK b ” and
hold until the first digit of your code
appears. Release the button.
7. Turn the lower knob to make the
second and third digits appear.
8. Press the lower knob and “000” will
appear on the display. Now you are
ready
to enter the last three digits of
your code.
9. Press “SEEK 4 ” or “SEEK b ” and
hold until the fourth digit of your
code appears. Release the button.
10. Turn the lower knob to make the
fifth and sixth digits of your code
appear.
11. Press the lower knob. “rEP” will
appear for five seconds, and then
“000” will appear.
through
11. If “SEC” appears, your
audio system is secured.
If “---”
shows on the display, your system is
not secured.
You must restart the
entire procedure again from step
5.
12. For verification, repeat steps 6
Shutting Off the Theft-Deterrent
Feature
If your audio system is secured (“SEC”
shows on display) and you wish to disable
it, enter your security code as follows,
pausing no more than
15 seconds
between steps:
1. Turn the ignition on. Make sure the
audio system is
off. The time will
show on the display.
together
until “SEC” shows on the
display.
3. Press “SET.” “000” will appear on the
display.
4. Press “SEEK 4 ” or “SEEK b ” and
hold until the first digit of your code
appears. Release the button.
5. Turn the lower knob until the second
and third digits appear.
6. Press the lower knob. “000” will
appear on the display.
7. Press “SEEK 4 ” or “SEEK b ” and
hold until the fourth digit of your
security code appears. Release the
button.
8. Turn the lower knob until the fifth and
2. Press pushbuttons “1” and “4”
sixth digits of your code appear.
9. Press the lower knob. If “---” shows,
you have shut off the theft-deterrent
feature. If
“SEC” shows, your audio
system is still secured.
NOTE: If you lose or forget your security
code, see your dealer for assistance.
Unlocking the Audio System after a
Power Failure
If power is disrupted to the audio system
while
in the “SEC” mode, the unit will
not work and “LOC”
will show on the
display whenever the ignition is on. To
unlock the unit:
1. Turn the ignition switch to the “Acc”
or “Run” position.
2. Press “SEEK 4 ” or “SEEK b ” and
hold until the first digit of your code
appears. Release the button.
3. Turn the lower knob to make the
second and third digits appear.
4. Press the lower knob. “000” will
appear on the display.
5. Press “SEEK 4 ” or “SEEK b ” and
hold until the
fourth digit of your
security code appears. Release the
button.
119.. .