1994 CHEVROLET CAMARO Owners Manual

Downloaded from www.Manualslib.com manuals search engine This is a mistake. Your brakes may not
have time to cool between hard stops.
Your brakes will wear out much faster if
you do a lot of heavy braking. If you keep
pace with the traffic and allow realistic
following distances, you will eliminate a
lot of unnecessary braking. That means
better braking and longer brake life.
If your engine ever stops while you’re
driving, brake normally but don’t pump
your brakes. If you
do, the pedal may
get harder to push down. If your engine
stops, you will still have some power
brake assist. But you will use
it when
you brake. Once the power assist is used
up, it may take longer to stop and the
brake pedal
will be harder to push.
inti-Lock Brakes (ABS)
tour Chevrolet has an advanced
klectronic braking system that
will help
- revent sludding.
ABS
INOP
?his light on the instrument panel will go
m when you start your vehicle.
Nhen you start your vehicle, or when yo1
)egin to drive away, you may hear a
nomentary motor or clicking noise. And
’ou may even notice that your brake
bedal moves a little while
this is going on
:his
is the ABS system testing itself. If
here’s a problem with the anti-lock brake
ystem, the anti-lock brake system
varning light will stay
on or flash.
;ee “Anti-Lock Brake System Warning
ight” in the Index.
1
127 ...

Downloaded from www.Manualslib.com manuals search engine Your Driving and the Road
Here’s how anti-lock works. Let’s say
the road is wet. You’re driving safely. Suddenly an animal jumps out
in front
You slam on the brakes. Here’s what
happens with ABS.
A computer senses that wheels are
slowing down. If one of the wheels is
about to stop rolling, the computer will
separately work the brakes at each front
wheel and at the rear wheels.
The anti-lock system can change the
brake pressure faster than any driver
could. The computer
is programmed to
make the most of available tire and road
conditions.
of you.
You can
steer around the obstacle while
braking hard.
As you brake, your computer keeps
receiving updates on wheel speed and
controls braking pressure accordingly.
Remember: Anti-lock doesn’t change the
time
you need to get your foot up to the
brake pedal.
If you get too close to the
vehicle in front of you,
you won’t have
time to apply your brakes if that vehicle
suddenly slows or stops. Always leave
enough room up ahead to stop,
even
though you have anti-lock brakes.
To Use Anti-Lock
Don’t pump the brakes. Just hold the
brake pedal down and let anti-lock
work for you. You may feel the system
working, or you may notice some noise, but this is normal. When your anti-lock
system
is adjusting brake pressure to help
avoid a braking skid, the
“LOW TRAC”
light will come
on. See “Low Traction
Light”
in the Index.
ASR (Acceleration Slip Regulation) System (Option:
LT1 VS Engine)
Your vehicle may have an ASR system
that limits wheel spin. This
is especially
useful in slippery road conditions. The
system operates only
if it senses that one
or both of the rear wheels are spinning or
beginning
to lose traction.
When this happens, the system works the
rear brakes and reduces engine power (by closing the throttle and managing spark)
to limit wheel spin.
The “LOW TRAC” light will come on
when your
ASR system is limiting wheel
spin. See “Low Traction Light” in the
Index. You may
feel the system working,
or you may notice some noise, but this is
normal.
The
ASR system may operate on dry
roads under some conditions, and you
may notice a reduction
in acceleration
when this happens.
This is normal and
doesn’t mean there’s a problem with
your
vehicle. Examples of these conditions
include a hard acceleration
in a turn, or
an abrupt upshift or downshift.
. . .I28

Downloaded from www.Manualslib.com manuals search engine ‘I i
If your vehicle is in cruise control when
the ASR system begins
to limit wheel
spin, the cruise control will automaticallq
disengage. When road conditions allow
you to safely use it again, you may
re-engage the cruise control. (See
“Cruise Control” in the Index.)
The “ASR” warning light will come on
when you tu-n the ASR system off. Whe~
the system is on, this light will come on
to let you know if there’s a problem with
your ASR system.
See “ASR System
Warning Light” in the Index.
When this warning light is on, the system
will not limit wheel spin. Adjust your
drjving accordingly.
ASR
The ASR system automatically comes on
whenever you start your vehicle.
To limit wheel spin, especially in
slippery road conditions, you should
always leave the system on. But you can
turn the ASR system
off if you ever need
to. (You should turn the system
off if
your vehicle ever gets stuck in sand,
mud, ice or snow.
See “Rocking Your
Vehicle” in the Index.)
To turn the system
off, press the button on
the console near the cigarette lighter. The
“ASIC” warning light will come on and
stay on. -If the ASR system is limiting
wheel spin when you press the button, the
system won’t turn off right away. It will
wait until there’s no longer a current need
to limit wheel spin. You
can turn the system back on at any
time by pressing the button again. The
*‘ASR’ warning light should go
off.
[f your car is equipped with P245/50ZR16
tires, the ASR system will automatically
turn
off at speeds above 108 mph (173
km/h). (The “ASR” warning light will
not come on.) When vehicle speed drops
below
103 mph (165 km/h), the system
will automatically turn on again.
Braking in Emergencies
Use your anti-lock braking system when
you need to. With anti-lock, you can
steer and brake
a1 the same time. In many
emergencies, steering can help you more
than even the very best braking.
129 ...

Downloaded from www.Manualslib.com manuals search engine Your Driving and the Road
Steering
Power Steering
If you lase power steering assist because
the engine stops or the system
is not
functioning, you can steer but it will
take much more effort.
Steering Tips
Driving
on Curves
It’s important to take curves at a
reasonable speed.
A lot of the “driver lost control” accidents
mentioned
on the news happen on curves.
Here’s
why:
Experienced driver or beginner, each of
us is subject to the same laws of physics
when driving
on curves. The traction of
the tires against the road surface makes it
possible for the vehicle to change its path
when you
turn the front wheels. If there’s
no traction, inertia will keep the vehicle
going in
the same direction. If you’ve
ever tried to steer a vehicle
on wet ice,
you’ll understand this.
The traction you can get in a carve
depends
on the condition of your tires and
the road surface, the angle at which the
curve is banked, and your speed. While
you’re in
a curve, speed is the one factor
you can control.
I
Suppose you’re steering through a sharp
curve, Then
you suddenly accelerate.
Both control systems
- steering and
acceleration
- have to do their work
where the tires meet the road. Unless you
have traction control and the system is
on, adding the sudden acceleration can
demand too much of those places. You
can lose control.
What should you do if this ever happens?
Ease
up on the accelerator pedal, steer the
vehicle the way you want
it to go, and
slow down.
Speed limit signs near curves
warn that
you should adjust your speed. Of course,
the posted speeds are based on good
weather and road conditions. Under less
favorable conditions you’ll want to
go
slower.
If
you need to reduce your speed as you
approach a curve, do it before
you enter
the curve, while your front wheels are
straight ahead.
Try to adjust your speed
so you can
“drive” through the curve. Maintain a
reasonable, steady speed. Wait to
accelerate until you are opt
of the curve,
and then accelerate gently into the
straightaway.
Steering in Emergencies
There are times when steering can be
more effective than braking. For example,
you come over a hill and find
a truck
stopped
in your lane, or a car suddenly
pulls
out from nowhere, or a child darts
out from between parked cars and stops
right in front
of you. You can avoid these
problems by braking
- if you can stop in
time. But sometimes you can’t; there isn’t
room. That’s the time for evasive action
- steering around the problem.
Your Chevrolet can perform very well in
emergencies like these. First apply your
brakes. It is better to remove as much
speed as you can from a possible
collision. Then steer around the problem,
. . ,130

Downloaded from www.Manualslib.com manuals search engine to the left or right depending on the space
available.
An emergency like this requires close
attention and a quick decision. If you are
holding the steering wheel at the
recommended
9 and 3 o’clock positions,
you can turn it a
full 180 degrees very
quickly without removing either hand.
But you have to act fast, steer quickly,
and just as quickly straighten the wheel
once you have avoided the object.
The fact that such emergency situations
are always possible is a good reason to
practice defensive driving at all times and
wear safety belts properly.
Off-Road Recovery
You may find sometime that your right
wheels have dropped
off the edge of a
road onto the shoulder (A) while you’re
driving.
If the level of the shoulder is only slight11
below the pavement, recovery should be
fairly easy. Ease off the accelerator and
then, if there
is nothing in the way, steer
so that your vehicle straddles the edge of
the pavement. You can
turn the steering
wheel up to
1/4 turn (B) until the right
front tire contacts the pavement edge.
Then
turn your steering wheel to go
straight down the roadway.
Passing
The driver of a vehicle about to pass
another on a two-lane highway waits for
just the right moment, accelerates, moves
around the vehicle ahead, then goes back
into the right
lane again. A simple
maneuver?
Not necessarily! Passing another vehicle
on a two-lane highway is a potentially
dangerous move, since the passing
vehicle occupies the same lane as
oncoming traffic for several seconds. A
miscalculation, an error
in judgment, or a
brief surrender to frustration or anger can
suddenly put the passing driver face to
face with the worst of all traffic accidents
- the head-on collision.
So here are some tips for passing:
“Drive ahead.” Look down the road,
to the sides, and to crossroads for
situations that might affect your
passing patterns. If you have any
doubt whatsoever about making a
successful pass, wait for a better time.
Watch for traffic signs, pavement
markings, and lines. If you can see a
sign
up ahead that might indicate a
turn
or an intersection, delay your
pass. A broken center line usually
131.. .

Downloaded from www.Manualslib.com manuals search engine Your Driving and the Road
a
a
indicates it’s all right to pass
(providing the road ahead is clear).
Never cross a solid line on your side
of the lane or a double solid line, even
if the road seems empty of
approaching traffic.
Do not get too close to the vehicle you
want to pass while you’re awaiting an
opportunity. For one thing, following
too closely reduces your area of
vision, especially if you’re following a
larger vehicle. Also, you won’t have
adequate space if the vehicle ahead
suddenly slows or stops. Keep back a
reasonable distance.
When it looks like a chance to pass is
coming up, start to accelerate but stay
in the right lane and don’t get too
close. Time your move
so you will be
increasing speed as the time comes to
move into the other lane. If the way is
clear to pass, you will have a “running
start” that more than makes up for the
distance you would lose by dropping
back. And
if something happens to
cause you to cancel your pass, you
need only slow down and drop back
again and wait for another
opportunity.
0
a
a
a
If other cars are lined up to pass a
slow vehicle, wait
your turn. But take
care that someone isn’t trying to pass
you as you pull out to pass the slow
vehicle. Remember to glance over
your shoulder and check the blind
spot.
Check your mirrors, glance over your
shoulder, and start your left lane
change signal before moving out of
the right lane to pass. When you are
far enough ahead of the passed vehicle
to see its front in your inside mirror,
activate your right lane change signal
and move back into the right lane.
(Remember that your right outside
mirror is convex. The vehicle you just
passed may seem to be farther away
from you than it really is.)
Try not to pass more than one vehicle
at a time on two-lane roads.
Reconsider before passing the next
vehicle.
Don’t overtake a slowly moving
vehicle too rapidly. Even though the
brake lights are not flashing, it may be
slowing down
or starting to turn.
If you’re being passed, make it easy
for the following driver to get ahead
of you. Perhaps you can ease a little to
the right.
loss of Control
Let’s review what driving experts say
about what happens when the three
control systems (brakes, steering and
acceleration) don’t have enough friction
where the tires meet the road to do what
the driver has asked.
In any emergency, don’t give up. Keep
trying to steer and constantly seek an
escape route or area of less danger.
Skidding
In a skid, a driver can lose control of the
vehicle. Defensive drivers avoid most
skids by taking reasonable care suited to
existing conditions, and by not
“overdriving” those conditions. But skids
are always possible.
The three types of skids correspond to
your Chevrolet’s three control systems. In
the brakmg skid your wheels aren’t
rolling. In the steering or cornering skid,
too much speed or steering in a curve
causes tires to slip and lose cornering
force. And in the acceleration skid too
. . .132

Downloaded from www.Manualslib.com manuals search engine much throttle causes the driving wheels to
spin.
A cornering skid is best handled by
easing your foot
off the accelerator pedal.
If you have the ASR system, remember: It
helps avoid only the acceleration skid. If
you do not have traction control, or
if the
system is
off, then an acceleration skid is
also best handled by easing your foot
off
the accelerator pedal.
If your vehicle starts to slide, ease your
foot
off the accelerator pedal and quickly
steer the way you want the vehicle to go.
If you start steering quickly enough, your
vehicle may straighten out. Always be
ready for a second skid if it occurs.
Of course, traction is reduced when water,
snow, ice, gravel, or other material is on
the road. For safety, you’ll want to slow
down and adjust your driving
to these
conditions. It is important to slow down
on slippery surfaces because stopping distance will be longer and vehicle
control more limited. While
driving on a surface with reduced
traction, try
your best to avoid sudden
steering, acceleration,
or braking
(including engine bralung by shifting to a
lower gear). Any sudden changes could
cause the tires to slide. You may not
realize the surface is slippery until your
vehicle is skidding. Learn to recognize
warning clues
- such as enough water,
ice or packed snow on the road to make
a .“mirrored surface”
- and slow down
when you have any doubt.
Remember: Any anti-lock braking system
(ABS) helps avoid only the braking skid.
. ..
I
4
Driving at Night
\Tight driving is more dangerous than day
hiving. One reason is that some drivers
tre likely to be impaired
- by alcohol or
lrugs, with night vision problems, or by
atigue.
lere
are some tips on night driving.
Drive defensively.
Don’t drink and drive.
Adjust your inside rearview mirror to
reduce the glare from headlights
behind you.
Since you can’t see as well, you may
need to slow down and keep more
space between
you and other vehicles.
133 ...

Downloaded from www.Manualslib.com manuals search engine Your Driving and the Road
Slow down, especially on higher
speed roads. Your headlights
can light
up only
so much road ahead.
0 In remote areas, watch for animals.
0 If you’re tired, pull off the road in a
safe place and rest.
Night Vision
No one can see as well at night as in the
daytime. But as we get older these
differences increase. A 50-year-old driver
may require at least twice as much light to
see the same thing at night as a
20-year-old.
What you do in the daytime can also
affect your night vision. For example, if
you spend the day in bright sunshine you
are wise to wear sunglasses. Your eyes
will have less trouble adjusting to night.
But if you’re driving, don’t wear
sunglasses at night. They may cut down
on glare from headlights, but they also
make a lot of things invisible.
You can be temporarily blinded by
approaching lights.
It can take a second or
two, or even several seconds, for your
eyes to readjust to the dark. When you are
faced with severe glare (as from a driver
who doesn’t lower the high beams, or a vehicle
with misaimed headlights), slow
down
a little. Avoid staring directly into
the approaching lights.
Keep your windshield and all the glass on
your vehicle clean
- inside and out.
Glare at night is made much worse by dirt
on the glass. Even the inside of the glass
can build up a film caused by dust. Dirty
glass makes lights dazzle and flash more
than clean glass would, malung the pupils
of your eyes contract repeatedly.
Remember that your headlights light up
far less of a roadway when you are in a
turn or curve.
Keep your eyes moving; that way, it’s
easier to pick out dimly lighted objects.
Just as your headlights should be
checked regularly for proper aim,
so
should your eyes be examined regularly.
Some drivers suffer from night blinduess
- the inability to see in dim light - and
aren’t even aware of
it.
Driving in the Rain
Rain and wet roads can mean driving
trouble. On a wet road you can’t stop,
accelerate or turn as well because your
tire-to-road traction isn’t as good as on
dry roads. And, if your tires don’t have
much tread left, you’ll get even less
traction. It’s always wise
to go slower
and be cautious if rain starts to fall
while you are driving. The surface may
get wet suddenly when your reflexes
are tuned for driving on dry pavement.
The heavier the rain, the harder it is to
see. Even if your windshield wiper blades
are in good shape, a heavy rain can make
it harder to see road signs and traffic
signals, pavement markings, the edge of
the road, and even people walking.
. . .I34