1994 CHEVROLET CAMARO Owners Manual

Downloaded from www.Manualslib.com manuals search engine When to Change Engine Oil:
See if any one of these is true for you:
0 Most trips are less than 4 miles
(6 km).
It’s below freezing outside and most
trips are less than
10 miles (1 6 km).
The engine is at low speed most of the
time (as in door-to-door delivery, or
in
stop-and-go traffic).
0 You tow a trailer often.
@ Most trips are through dusty places.
If any one
of these is true for your
vehiclej
then you need to change your oil
and filter every 3,000 miles (5 000 km) or
3 months - whichever comes first.
If none of them is true, change the oil
every
7,500 miles (12 500 km) or 12
months - whichever comes first. Change
the filter at the first oil change and at
every other oil change after that.
Engine Coolant Heater (Engine Block
Heater):
An engine coolant heater can be a big
help
if you have to park outside in very
cold weather,
0” F (- 18 “C) or colder. If
your vehicle has this option, see “Engine
Coolant Heater”
in the Index.
What to Do with Used Oil:
Did you know that used engine oil
contains elements that may be unhealthy
for your skin and could even cause
cancer? Don’t let used oil stay on your
skin for very long. Clean your skin and
nails with soap and water, or a good hand
cleaner. Wash or properly throw away
clothing or rags containing used engine
oil. (See the manufacturer’s warnings
about the use and disposal
of oil
products.)
Used oil can be a real threat to the
environment. If
you change your own oil,
be sure to drain all free-flowing oil from
the filter before disposal. Don’t ever
dispose of oil by putting it in the trash,
pouring
it on the ground, into sewers, or
into streams
or bodies of water. Instead,
recycle it by taking it to a place that
collects used oil. If you have a problem
properly disposing of your used oil, ask
your dealer, a service station or a local
recycling center for help.
3.4L L32 (Code S
air Cleaner
tefer to the Maintenance Schedule to
letermine when
to replace the air filter.
;ee “Scheduled Maintenance Services” ir
he Index.
191 ...

Downloaded from www.Manualslib.com manuals search engine Service and Appearance Care
~~
5.7L LT1 (Code Pb
NOTICE:
If the air cleaner is off, a backfire can
cause a damaging engine fire. And,
dirt can easily get into your engine,
which will damage it. Always have
the air cleaner
in place when you’re
driving.
Air Filter Replacement
To remove the air filter:
1. Remove the two plastic pins by
pulling them straight up.
. . .192

Downloaded from www.Manualslib.com manuals search engine 2. Disconnect the plastic clamp on the
duct. Pull apart the connection.
3. Pull the air cleaner straight up.
Unclamp the metal clips. 4. Open the air cleaner and remove the
filter.
193 ...

Downloaded from www.Manualslib.com manuals search engine Service and Appearance Care
Automatic Transmission FIuid
When to Check and Change:
A good time to check your automatic
transmission fluid level is when the
engine oil is changed. Refer to the
Maintenance Schedule to determine when
to change your fluid. See “Scheduled
Maintenance Services” in the Index.
How to Check:
Because this operation can be a little
difficult, you may choose to have this
done at a Chevrolet dealership Service
Department.
If
you do it yourself, be sure to follow all
the instructions here, or
you could get a
false reading on the dipstick.
NOTICE:
Too much or too little fluid can dam-
age your transmission.
Too much can
mean that some of the fluid could
come out and fall on hot engine parts
or exhaust system, starting a fire. Be
sure to get an accurate reading if you
check your transmission fluid.
. . ,194
Wait at least 30 minutes before checking
the transmission fluid level
if you have
been driving:
When outside temperatures are above
90°F (32°C).
0 At high speed for quite a while.
0 In heavy traffic - especially in hot
weather.
While pulling a trailer.
To get the right reading, the fluid should
be at normal operating temperature,
which is 180°F to
200°F (82°C to 93°C).
To check transmission fluid hot: Get
the vehicle warmed up
by driving
about
15 miles (24 km) when outside
temperatures are above 50°F (10°C). If
it’s colder than
50°F (lO”C), drive the
vehicle
in “D” (Third Gear) until the
engine temperature gage moves and then
remains steady for ten minutes. Then
follow the hot check procedures.
To check transmission fluid cold: A cold
check is made after the vehicle has been
sitting for eight hours or more with the
engine off and is used only as a reference.
Let the engine run at idle for five minutes
if outside temperatures are 50°F
( 10°C)
or more. If it’s colder than 50°F (lO”C),
you may have to idle the engine longer. Should the fluid level
be
low during a
cold check, you must perform a hot check
before adding fluid This will give you a
more accurate reading
of the fluid level.
To check the fluid hot or cold:
Park your vehicle on a level place.
With the parking brake applied, place
With your foot on the brake pedal,
the shift lever
in
“P’ (Park).
move the shift lever through each gear
range, pausing for about three seconds in each range. Then, position the shift
lever in
“F’” (Park).
minutes or more.
Let the engine run at idle for three

Downloaded from www.Manualslib.com manuals search engine 3.4L L32 (Code S)
Then, without shutting off the engine,
follow these
steps:
1. Pull out the dipstick and wipe it with a
clean rag or paper towel.
5.7L LT1 (Code P)
2. Push it back in all the way, wait three
seconds and then pull
it back out
again.
3. Check both sides of the dipstick, and
read the lower level. The fluid level
must be
in the “COLD’ area for a cold
check or
in the “HOT” area or
cross-hatched area for a hot check.
4. If the fluid level is in the acceptable
range, push the dipstick back
in all the
way.
How to Add Fluid:
Refer to the Maintenance Schedule to
determine what kind of transmission fluid
to use. See “Recommended Fluids and
Lubricants” in the Index.
195 ...

Downloaded from www.Manualslib.com manuals search engine Service and Appearance Care
If the fluid level is low, add only enough
of the proper fluid to bring the level up to
the “COLD’ area for a cold check or the
“HOT” area for a hot check. It doesn’t
take much fluid, generally less than a pint.
Don’t overfill. We recommend you
use
only fluid labeled DEXRON@-III or
DEXRON@-IIE, because
fluids with that
label are made especially for your
automatic transmission. Dama e caused
by fluid other than DEXRON
-111 or
DEXRON@-IIE is not covered by your
new vehicle warranty.
After adding fluid, recheck the fluid
level as described under
“How to
Check.”
obtained, push the dipstick back in all
the way.
D
When the correct fluid level is
Manual Transmission Fluid
How to Check:
Because this operation can be difficult,
you may choose to have this done at a
Chevrolet dealership Service Department.
If you do it yourself, be sure to follow all
the instructions here, or
you could get a
false reading.
Too much or too little fluid can
damage your transmission.
Too much
can mean that some of the fluid could
come out and fall on hot engine parts
or exhaust system, starting a fire. Be
sure to get an accurate reading if you
check your transmission fluid.
Check the fluid level only when your
engine is off, the vehicle is parked on a
level place and the transmission is cool
enough for you to rest your fingers on
the
transmission case.
Then, follow these steps:
1. Remove the filler plug.
2. Check that the lubricant level is up to
the bottom of
the filler plug hole.
3. If the fluid level is good, install the
plug and be sure it
is fully seated. If
the fluid level is low, add more fluid
as described in the next steps.
How to Add Fluid:
Here’s how to add fluid. Refer to the
Maintenance Schedule to determine what
kind
of fluid to use. See “Recommended
Fluids and Lubricants” in the Index.
1. Remove the filler plug.
2. Add fluid at the filler plug hole. Add
only enough fluid to bring the fluid
level up to the bottom of
the filler
plug hole.
3. Install the filler plug. Be sure the plug
is fully seated.
,. 196

Downloaded from www.Manualslib.com manuals search engine Hydraulic Clutch
The hydraulic clutch in your vehicle is
self-adjusting. The clutch master cylinder
reservoir is filled with hydraulic clutch
fluid.
It isn’t a good idea to “top off’ your
clutch fluid. Adding fluid won’t correct a
leak.
A fluid loss in this system could indicate
a problem. Have the system inspected and
repaired.
When to Check and What to Use:
Refer to the Maintenance Schedule to
determine how often you should check
the fluid level
in your clutch master
cylinder reservoir and for the proper fluid.
See “Owner Checks and Services” and
“Recommended Fluids and Lubricants”
in the Index.
How to Check:
The proper fluid should be added if the
level is below the
“STEP” mark on the
reservoir. See the instructions on the
reservoir cap.
Rear Axle
When to Check and Change Lubricant:
Refer to the Maintenance Schedule to
determine how often to check the
lubricant and when
to change it. See
“Periodic Maintenance Inspections’’
in
the Index.
How to Check Lubricant:
If the level is below the bottom of the
filler plug hole, you’ll need to add some
lubricant. Add enough lubricant to raise
the level to the bottom of the filler plug
hole.
What to Use
Standard Differential
Use Axle Lubricant (GM Part No.
105227 1 ) or SAE 80W-90 GL-5 gear
lubricant.
Limited-Slip Differential
To add lubricant when the level is low,
use Axle Lubricant (GM Part
No.
105227 1 ) or SAE 80W-90 GL-5 gear
lubricant. To completely refill after
draining, add
4 ounces (1 18 ml) of
Limited-Slip Differential Additive
(GM Part No. 1052358). Then fill to the
bottom of the filler plug hole with Axle
Lubricant (GM Part
No. 12345977) or
SAE 80W-90 GL-5 gear lubricant.
197 ...

Downloaded from www.Manualslib.com manuals search engine Service and Appearance Care
Engine Coolant
The following explains your cooling
system and how to add coolant when
it
is low. If you have a problem with
engine overheating or if you need
to add
coolant to your radiator, see “Engine
Overheating” in the Index.
The proper coolant for your Chevrolet
will:
0 Give freezing protection down to
Give boiling protection up to 262°F
Protect against rust and corrosion.
0 Help keep the proper engine
Let the warning lights work as they
-34°F (-37°C).
(128°C).
temperature.
should.
What to Use:
Use a mixture of one-half clean water
(preferably distilled) and one-half
antifreeze that meets “GM Specification
1825M,” which won’t damage aluminum
parts.
You can also use a recycled coolant
conforming to GM Specification
1825M
with a complete coolant flush and refill. If
you use
this mixture, you don’t need to
add anything else.
NOTICE:
If you use an improper coolant mix,
your engine could overheat and be
badly damaged. The repair cost
wouldn’t be covered by your war-
ranty.
Too much water in the mix can
freeze and crack the engine, radiator,
heater core and other parts.
. . .I98