1991 MITSUBISHI ECLIPSE lock

21-78MANUAL TRANSAXLE - Special Tools
MD99881 9Installer adapter (40)Installation of front differential bearings
M D998820Installer adapter (42)Installation of center differential bearings and
driven bevel gear bearing
MD999566ClawRemoval of bearing outer race from
intermediate gear, front output shaft, and
center differential
MD998827Installer adapter (56)Installation of drive bevel gear bearing
MB990326Preload socketMeasurement of drive bevel gear shaft
rotating torque
M B990900(included in
MB990988)Side gear holding
Tool (A)Measurement of drive bevel gear shaft
rotating torque
MB991 013Special spannerInstallation and removal of driven bevel gear
lock nut
MB991 193PlugPrevention of transfer oil discharge and
foreign object entry

MANUAL TRANSAXLE - Transaxle
4*
4*
30-35 Nm
22-25 ft.lbs.
\
/9-13 Nm7-10 ft.lbs.24-35 Nm
17-25
ftibs26-33 ft.lbs.
70-80 Nm r51-58 ft.lbs.09A013910. Under cover
11. Cotter pinI 2. Connection for tie rod end
13. Self-locking nut
14. Connection for lower arm ball joint
+e I)* 15. Connection for drive shaft
16. Circlip
::17. Front exhaust pipe
18. Transfer assembly
19. Bell housing cover
20. Right member
21. Gusset
22.
Lf:saxle assembly lower part coupling
~~ ~~ 23. Transaxle assemblyNOTE
(1) Reverse the removal procedures to reinstall.
(2) l * : Refer to “Service Points of Removal”.
(3) l 4 : Refer to “Service Points of Installation”.(4) m : Non-reusable parts

21-86MANUAL TRANSAXLE - Transaxle AssemblyTRANSAXLE ASSEMBLY
DISASSEMBLY AND REASSEMBLY
30-35 Nm
22-25 ft.lbs.
\
30-35 Nm
22-25 Wbs.
4.0-5.5 Nm\62.9-3.9 ft.lbs.7-42 Nm
-30
ft.lbs.llI8-59
I21IDisassembly steps
l + 1. Rear cover
2. Wave spring
I)+ 3. Screw bolts
4. Reverse brake cone
;. E;zk;p light switch
7: Restrict ball assembly
8. Gasket
9. Poppet plug
.- ^1 U. Poppet spring11. Poppet ball
I 2. Speedometer driven gear assembly
l + 13. Air breather
l * l 4 14.Spring pin
140-160 Nm
w ”Y
102-115 ft.lbs.
16Bl/
22
++ I)+ 15. Lock nut+el 416.Lock nut
l + 17. 5th speed synchronizer assembly~~ 18. Shift fork
19.Synchronizer ring
20.
5th speed gear
21.Needle bearing
22.
5th speed intermediate gear35-42 Nm
26-30 ft.lbs.-1
TFMOOZSNOTE
(1) Revers_e the di?: ’(2) +-(3) +v : neler 10(4) IW : Non-reusat-yle parts.assembly
proceaures 10 reassemble.ry : KeTer to Service Points of Disassembly”.“-I-- I- “Service Points of Reassembly”.
’
i

MANUAL TRANSAXLE - Transaxle Assembly
SERVICE POINTS OF DISASSEMBLYNZlMFAT
14. REMOVAL OF SPRING PINriiRemove the spring pin using the special tool.
.,
15.116. REMOVAL OF LOCK NUTS
(1) Unstake lock nuts of the input shaft and intermediate
gear.(2) Shift the transaxle into reverse using the control lever
and select lever.
(3) Install the special tool on the input shaft.
(4) Install the spinner handle and 10 mm
(.039 in.) bolt.
(5) Remove the lock nuts.
A

MANUAL TRANSAXLE - Transaxle Assembly(3) Rotate the shift controls in the direction of the arrow in
numerical order. Remove the shift lugs from the controlfinger and interlock plate.
(4) Raise each of the shift rails upward and remove them
from the clutch housing.
(5) Remove the all shift rails and forks.
59. REMOVAL OF INTERMEDIATE GEAR ASSEMBLY/
60. INPUT SHAFT ASSEMBLY
Lift up the input shaft assembly and remove the intermedi-
ate gear assembly.
61./62./64. REMOVAL OF OUTER RACE
Using the special tool, remove the outer race.
SERVICE POINTS OF REASSEMBLYN21MGAPa69. INSTALLATION OF MAGNET HOLDER/68. MAGNET
Install the magnet and magnet holder, ensuring they are
installed in the correct direction.
67. INSTALLATION OF OIL SEAL
Using the special tool, install the rear output shaft oil seal.

21-94MANUAL TRANSAXLE - Transaxle Assembly
5mm(.21 in.)TFM006357. INSTALLATION OF BOLT
Apply adhesive to the bolt threads.
Specified adhesive: MOPAR Part No.4318031
or MOPAR Part No.4318032
or equivalent
Caution
Be careful not to apply to adhesive to the bold head.
56. INSTALLATION OF SHIFT RAIL ASSEMBLY
(1) Shift the Ist-2nd synchronizer sleeve into 2nd speed.
(2) Shift the
3rd-4th synchronizer sleeve into 4th speed.
(3)Fit the shift forks of shift rail assembly to their groove of
sleeves.
(4) Install the shift rails, rail holes of clutch housing.
(5) Turn the shift rails in the directions indicated by the
arrows in the order shown in the illustration, and
engage the shift lugs to control finger and interlock
plate.
55./54. INSTALLATION OF SPRING PINS
Using the special tool, drive the spring pins into position.
Make sure that the slit in the spring pin is aligned with the
shift rail centerline.
Caution
Do not reuse the spring pins.

21-98MANUAL TRANSAXLE - Transaxle Assembly
16.115. INSTALLATION OF LOCK NUTS
(1) Shift the transaxle into reverse using the control lever
,+and select lever.
.,./(2) Install the special tool on the input shaft.
(3) Fit on the spinner handle and bolt.
(4) Tighten the lock nut to specification and then loosen it
completely before tightening it again to the specified
torque.
i;(5) Punch the lock nut into locked position.
(Punch two places on the lock nut of the input shaft andone place on the lock nut of the intermediate gear.)
14. INSTALLATION OF SPRING PIN
(1) Using the special tool, drive the spring pin into position.(2) Make sure that the slit in the spring pin is aligned with
the shift rail center line.
CautionDo not reuse the spring pin.A

21-106MANUAL TRANSAXLE - Front Differential
FRONT DIFFERENTIAL
DISASSEMBLY AND REASSEMBLY
NZIMMAG
i;&
Disassembly stepsl + 1. Bolt
2. Differential drive gear
** l +3. Ball bearing+* l * 4. Lock pinI)+ 5. Pinion shaft
l * 6. Pinion
I)+ 7. Washer
l + 8. Sidegear
95-lOl ft.lbs.l * 9. Spacer10. Differential case
NOTE(I)Reverse the disassembly procedures to reassemble(2)C*: Refer to “Service Points of Disassembly”.(3)l +: Refer to “Service Points of Reassembly”.(4)q : Non-reusable parts.
:&
-_-
160015
Press
teal case 2200095
SERVICE POINTS OF DISASSEMBLY3. REMOVAL OF BALL BEARING
Using the special tool, remove the ball bearing.
Caution
Do not reuse the bearing if it has been removed from
the differential case.
4. REMOVAL OF LOCK PIN
Drive out the lock pin from hole A using a punch.