1991 MITSUBISHI 3000GT belt

INTERIORCONTENTSNWAA-A~
FLOOR CONSOLE*
____....._.........__._..._......_..._...... 11
REAR SEAT . .._._____..______....____.._.._._..___.._._____.....___....24
FRONT SEAT*
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18SEAT BELT*. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25IHEADLINING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17TRIMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12INSTRUMENT PANEL*
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . .
i
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components, (that may have to beremoved/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(I)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead topersonal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (fromrendering the SRS inoperative).(2) Service or maintenance of any SRS component or SRS-related component must be performed only at anauthorized MITSUBISHI dealer.(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B -Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.
2I

INTERIOR - Troubleshootina
TENSION-REDUCER TYPE SEAT BELT
M52EBIACIRCUIT DIAGRAM
ON(IGIlFUSIBLE LiNK@Im
Ia
E?I
qEl2C-68 ,.l 'I/C I/“I u0
1OA015A
,XL
z C-80
i
1 c-77j1'121"14151sij[pER@gqi
C-Slm 3
pTE$i@
r
d
F-19 $6
E-26
@yiq
2
FRONT SEAT;;B; S;;Y$H
FRONT SEATE-14BELT SOLENOID
/EzJ(RH)(LH)
2
I
E-20
m
1
EFS?J---_-___-~~~~__---I
:2cpjX3cc351ck---------------j2_----1kC-65
pziEgqX'
mx2
IIII
I
I
06L----v-----------v ________ Y
7 16"7 14:'" Err1
>>& lo:20
c-?9 PI
SELF-DIAGNOSIS mCHECK CONNECTORat1:VEHTCT.F.S WiTHOUT
\ (RI%(LH) /
#jT m- @$;"LA"'4
*cl - \PxJTPI UC w+c.v,a,,,uhhu ,,ITH7.iREpp&JqH(35AC-RlSlO-NYDOOR SWITCH
;tjgFgiALARMTSB Revision

INTERIOR - Troubleshootinn52A-5OPERATION
l If the driver fastens the seat belt with the
ignition switch placed in the “ON” position, the
seat belt switch in the seat belt buckle is turned
“ON” to operate the seat belt solenoid in the
retractor.
lThis will reduce the seat belt rewinding torque
to minimize a sense of oppression given by the
belt.
lOwing to the timer function of the ETACS unit,
the seat belt solenoid is kept in operation for 30
seconds after turning off the ignition switch,
with due consideration to elimination of the
sudden rise in a sense of oppression caused by
the belt immediately after the ignition switch is
turned off.
COMPONENT LOCATION
ETACS unitNameSymbolA19FO134TROUBLESHOOTING HINTS
The seat belt solenoid does not function
(I) The power window does not operate as well.
lCheck the ETACS unit. (Refer to GROUP 42-Power Window.)
(2) The power window operates.
l Check dedicated fuse No. 1 and 19.
(3) Some of the tension reducers do not operates
l Check the inoperative seat belt switch.
l Check the inoperative seat belt solenoid.
I
1 TSB Revision

INTERIOR - Troubleshooting52A-7OPERATION
Key-reminder warning
L0 Battery voltage is always supplied, through
fusible link No. 6 to the key-reminder switch.
l When the driver’s seat is opened while the
ignition key is still in the key cylinder, the door
switch is switched ON, electricity flows to
fusible link No. 6, the key-reminder switch, the
buzzer, the door switch, and ground, and the
buzzer sounds.
Seat belt warning
lBattery voltage is applied, through fuse No. 11
to the ETACS unit when the ignition key is at the
“ON” position.
l Electricity flows to fusible link No. 6, the seat
belt warning light, the ETACS unit, and ground,
and the seat belt warning light flashes for
approx. 6 seconds.
lIf the driver does not buckle the seat belt, the
seat belt switch is switched ON, electricity
flows to fusible link No. 6, the key-reminder
switch, the buzzer, the seat belt switch, the
ETACS unit, and ground, and the buzzer sounds
for approx. 6 seconds.
lWhen the driver buckles the seat belt, the seat
belt switch is switched OFF and the buzzer
stops.
COMPONENT LOCATION
Name1 Symbol (
ETACS unitIA t19FO134TROUBLESHOOTING HINTS
Key-reminder warning
The key-reminder warning doesn’t sound.
(I) The seat belt warning function is OK.
l Check the door switch.
(2) The seat belt warning also doesn’t function.
l Check the buzzer.
Seat belt warning
1. The seat belt warning doesn’t function.
(I) The seat belt warning light flashes.
l Check the seat belt switch.
(2) The seat belt warning light also does not
function (and the key-reminder warning also
does not function).
l Check the key-reminder switch.
2. The buzzer doesn’t stop even though the driv-
er’s seat belt has been buckled.
l Check the seat belt switch.
3. The seat belt warning light doesn’t flashes (but
the buzzer sounds).
l Check the light bulb.
NOTEFor the inspection of the ETACS unit, refer to
P.52A-25.16FO35
1 TSB Revision

52A-14
INTERIOR - Trims
Scuff plate
19FOO46
33 ftlbs.19FOl60
Quarter trim removal steps
** ** 11. Rear seat
12. Shelf cover assembly
13. Shelf catcher
14. Cover
15. Garnish19. Rear seat belt anchor plate mounting bolt
20. Screw
21. Quarter trim
22. Rear side trim (Refer to
P.52A-15.)23. Quarter trim bracket
16. Sash guide cover mounting bolt
17. Front seat belt anchor plate mounting bolt
18. Retractor cover
NOTE*: Location of resin clipSERVICE POINT OF REMOVAL
11. REMOVAL OF REAR SEAT
With the lever pulled forward, raise the seat cushion to
remove it.
TSB Revision

INTERIOR - Trims52A-15

ISERVICE POINT OF INSTALLATION
11. INSTALLATION OF REAR SEAT
(1) Fit the seat cushion attachment wire under the seat-back positively.
(2) Pass the rear seat belt buckles through the. seat
cushion.
(3) Insert the lock plate of seat cushion in the hole provided
in the floor positively.
4-A{-
Rear endtrimB-Br-Rear side trim, rear end trim removal steps
I. Luggage compartment floor box (R.H.)2. Luggage compartment floor box (L.H.)9. Luggage compartment light connector con-
nection_ -10. Hear side trim
NOTE(1) @ : Location of metallic clip(2) * : Location of resin clip 3. Lid
(R.H.)4. Lid (L.H.)5. Rear end trim
6. Screws
7. Floor mat mounting clip
8. High floor center board
1 TSB Revision

INTERIOR - Front Seat52A-21
IISASSEMBLY AND REASSEMBLY
DRIVER SEAT

18
8,‘(-i
Q45
Nm45
NmP
ii filbs.20-7;s
I24 Nm17 ftlbs.19FO18324N;17 ftlbs.
19FO136
FRONTPASSENGER SEAT18
.23Removal stepsI. Reclining adjuster knob
2. Plug
3. Cap
1“+Qnrl~rrl driver seat)
4. Height adiuster lever I v~““~‘” L5.
POtier S&t switch B
6. Adjuster cover(Sporty driver sent)-- - - . ,7. Side shield cover (L.H.)
8. Side shield cover
(R.H.)l a9. Inner seat beltIO. Seat cushion assembly11. Memorv reclinina knob (Driver seat)
12. Sliding adjuster (nob13. Seat back panel (Except standard driver seat)
14. Seat back assembly
15. Seat belt guide
16. Lumbar support knob
17. Lumbar support aarnish
7(Stand& dri\mr -19. Reclinina adiuster lower cover (Driver seat)
20. Height adjuster (Standard driver seat)
21. Power seat harness
22. Power seat adjuster1
(SporVdrivr----”23. Walk-in knob
’’--4X-1
24. Walk-in knob garnish
25. Slide adjuster(Front passenger seat)24Nm
171, Ihc19FO184
1 TSB Revision

INTERIOR - Front Seat52A-23
(2) Disconnect the connector of each limit switch and check for
continuity between terminals.
lFr= ) I / * / 3 j
Highest00
Medium0
Lowest0
0
NOTEO-O indicates that there is continurty between the terminals,
(3) Make sure that portion A of the harness does not interfere
with the selector gear.
SERVICE POINT OF REASSEMBLY9. INSTALLATION OF INNER SEAT BELT
(1) Route the seat belt switch connector harness on the
adjuster bracket.
(2) Use clips to secure the harness to the adjuster bracket.
(3) Fit the locking claw of the inner seat belt positively in
the locking hole provided in the seat bracket.
iJ
TSB Revision