1991 MITSUBISHI 3000GT dimensions

GENERAL - General Data and Specifications
GENERAL DATA AND SPECIFICATIONS
00-21
MOOHA- -
c-i----J---i!--8GENERALSPECIFICATIONS
Vehicle dimensionsmm (in.)
Overall length
1
Overall width2
Overall height3
Wheelbase4
Tread
Front5
Rear6
OverhangFront7
Rear8
Minimum running groundclearance9
Angle of approachdegrees10
Angle of departuredegrees11
Vehicle weightkg (tbs.)
Curb weights
MIT
AI-T
Gross vehicle weight rating
Gross axle weight rating
Front
Rear
Seating capacity
Engine
Model No.
Piston displacementcm” (cu.in.)
3000GT
(Non-Turbo)
4,545(178.9)
1,840(72.4)
1,285(50.6)
2,470(97.2)
1,560(61.4)
1,580(62.2)
1,025(40.4)
1,050(41.3)
145(5.7)
12.2”
16.9”
1,455 (3,208)
1,495 (3,296)
1,925 (4,244)
1,100 (2,425)
850 (1.874)
4
6G72-(DOHC)
2,972 (181.4)3000GT SL
(Non-Turbo)
4,545(178.9)
1,840(72.4)
1,285
(50.6)
2,470(97.2)
1,560(61.4)
1,580(62.2)
1,025(40.4)
1,050(41.3)
145(5.7)
12.2”
16.9”
1,520 (3,351)
1,560 (3,439)
1,925 (4.244)
1,100 (2,425)
850 (1,874)
4
6G72-(DOHC) -
2,972 (181.4)
+64
OOFO015
3000GT VR-4
(Turbo)
4,545(I 78.9)
1,840
(72.4)
1,285(50.6)
2,470(97.2)
1,560(61.4)
1,580(62.2)
1,025(40.4)
1,050(41.3)
145 (5.7)
12.2”
16.9”
1,710 (3.770)1,720 (3,792)“’
-
2,050 (4.519)
1,110 (2,447)940
(2,072)
4
6G72-(DOHC)
2,972 (181.4)
NOTE“I : <4ws>
1 TSB Revision

22-60MANUAL TRANSAXLE - Transaxle Assembly
TRANSAXLE ASSEMBLY
The W5MGl transaxle cannot be disassembled.
If any parts other than describes below are defective, replace the transaxle assembly.
REPLACEABLE PART
1.l * 2.
3.
*a 4.l 4 5.6.
Transaxle to transfer connecting boltTransfer case oil seal
Transfer oil seal guide
Input shaft rear seal cap
Center shaft oil sealAir vents (breather caps) for transaxle and
transfer
Oil filler plugs for transaxle and transfer
Oil drain plugs for transaxle and transfer
TFM0157
SERVICE POINTS OF INSTALLATION6. INSTALLATION OF CENTER SHAFT OIL SEAL
Fabricate a tool having the following dimensions from a
pipe to install the oil seal.
Dimension :
I.D.. . . ..___........._...................... Approx. 27 mm (1.06 in.)
O.D.
. . . . . .._...........___............_.....Approx. 31 mm (1.22 in.)
Length . . . . . . . . . . . . . . . ..__......._____.Approx. 200 mm (7.87 in.)
TSB Revision

27-6
REAR AXLE tAWD> - Specifications
REAR AXLE
SPECIFICATIONS&L/j ~
GENERAL SPECIFICATIONSM27CA-8
Items
Axle shaft
We
Shaft dimensionsmm (in.)
Outer bearing portion dia.
inner bearing portion dia.
Center portion dia.
Overall length
Bearing
O.D. x I.D.mm (in.)
Outer
Inner
Drive shaft
Joint type
Outer
Inner
Length (joint to joint) x diametermm (in.)
Differential
Reduction gear type
Reduction ratio
Differential gear type and configuration
Side gear
Pinion gear
Number of teeth
Drive gear
Drive pinion
Side gear
Pinion gear
Bearing
O.D. x I.D.mm (in.)
Side
Front
Rear
Specifications
Semi-floating type
35 (1.38)
28(1.10)
34.5 (1.36)
245.4 (9.7)
72 x 35 (2.83 x 1.38)
58 x 28 (2.28 x 1
.I 0)
B.J.
T.J.
395x28(15.6x1.10)
Hypoid gear
3.545
Straight bevel gear x 2”
Straight bevel gear x 4
39
11
16
IO
82.500 x 45.242 (3.25 x 1.78)
68.263 x
30.163 (2.69 x 1.19)
76.200 x 36.513 (3.00 x 1.44)
NOTE*.Denotes the gear (L.H.) which is in a single body with the viscous coupling.B:J.: Birfield JointT.J.: Tripod JointTSB Revision

37B-84-WHEEL STEERING SYSTEM (4WS) - Power Cylinder
(4) When the tie rod ends and the installation holes at the
trailing arm do not meet, loosen the tie rod end securing
nut, then adjust the length. The dust cover fastener clip
should be removed for this.
(5) The difference between the lengths of the left and
right’
Ljtie rods should be less than 1 mm
( ,039 in.).
NOTEThe threads of the tie rod ends may be used as a guide
for this.
DISASSEMBLY AND REASSEMBLYM37SE. -
::::::::::::;::: ::.
&
:::::y .:::5;:;. . . . . . . . .. .
11.
13G0070
Grease: Silicone greaseDisassembly steps
1. Nut**2. Tie rod end assembly3.Clip4.Wirel *5. Dust cover6.Bleedercaps
7.Bleeder screws8.Cylinder assembly
2
13A0128
13G0070
Rod13A025
SERVICE POINTS OF REASSEMBLYM37SHAA5. INSTALLATION OF DUST COVER
Apply the specified grease to the place indicated in the
illustration, then install the dust cover to the cylinder
assembly.
Specified grease: Silicone grease2. INSTALLATION OF TIE ROD END ASSEMBLY
Temporarily attach the tie rod end assembly to the cylinder
assembly at the place of dimension as illustrated.
NOTETo adjust the assembly dimensions of the tie rod end
assembly, remove the dust cover clip and rotate the rod.
TSB Revision