1986 TOYOTA CAMRY V20 check oil

(e) Tighten the O±ring fittings or the bolted type fittings to
the specified torque.
4. WHEN CONNECTING MANIFOLD GAUGE;
(a) Be sure to connect the charging hose end with a pin
to the compressor charging valve.
(b) The letter ºDº engraved near the compressor service
valve indicates the high pressure side, and ºSº indi-
cates the low pressure side. Pay careful attention
when connecting the hose.
(c) Tighten hose by hand.
(d) To prevent loosening of connected hose, do not apply
drops of compressor oil to the seat of connection.
HINT: After connecting the manifold gauge and the refrig±
erant container (service can), discharge any air in the
hoses.
5. WHEN EVACUATING;
Approx. 15 minutes after removal, check the system for
leaks, then take at least another 15 minutes to make sure
the air is fully removed.
6. WHEN HANDLING REFRIGERANT CONTAINER
(SERVICE CAN);
(a) Must never be heated.
(b) Must be kept below 4

°C (1 04°F).
(c) If warming service can with hot water, be careful that
the valve on top of the service can is never immersed
in the water, as the water may permeate into the refrig-
erant cycle.
(d) Empty service cans must never be re±used.
7. WHEN A/C IS ON AND REFRIGERANT GAS IS
BEING REPLENISHED;
(a) If there is not enough refrigerant gas in the refrigerant
cycle, oil lubrication becomes insufficient and com-
pressor burnout may occur, so take care to avoid this.
(b) If the valve on the high pressure side is opened, refrig-
erant flows in reverse and causes the service can to
rupture, so only open and close the vlave on the low
pressure side.
(c) If the service can is inverted and refrigerant is inserted
in a liquid state, the liquid is compressed and the com-
pressor brakes down, so the refrigerant must be in-
serted in a g¿¿seous state.
(d) Be careful not to insert too much refrigerant gas, as
this causes trouble such as inadequate cooling, poor
fuel economy, engine overheat, etc.
8. WHEN USING GAS±CYLINDER TYPE LEAK
DETECTION INSTRUMENT;
(a) As a naked flame is used, first make sure that there are
no flammable substances nearby before using it.
(b) Be careful, as poisonous gas is produced when
refrigerant gas comes in contact with heat parts.
± AIR CONDITIONING SYSTEMGenera! InformationAC±3

Discharging of Refrigeration System
Evacuating and Charging of
Refrigeration System
(See Air Conditioning Fundamentals and Repairs Pub. No.
36950E)
Condenser clogged
Drive belt slipping
Magnetic clutch faulty
Compressor faulty
Expansion valve faulty
Thermistor faulty
A/C amplifier faulty
Insufficient or too much refrigerant
Air or excessive compressor oil in
system
Receiver clogged
Water valve cable set faultyCheck condenser .
Check or replace drive belt
Check magnetic clutch
Check compressor
Check expansion valve
Check thermistor
Check amplifier
Check refrigerant volume
Evacuate and charge system
Evaporator clogged or frosted
Air leakage from cooling unit or air duct
Air inlet blocked
Blower motor faulty
A/C amplifier faulty
Drive belt slipping
Revolution detecting sensor faulty
(w/Power steering)
A/C amplifier faultyAC±33
AC±21
AC±23
AC±23
AC±39
AC±43
AC±45 to 47
AC±22
Repair as necessary
Replace blower motor
Check amplifierClean evaporator fins or filters
Repair as necessary
Check or replace drive belt
Check sensor
Check receiver
Reset water valve cable
A/C switch
indicator
flashingInsufficient
velocity of cool
airAC±41
AC±39 to 42 Insufficient
cooling
Check amplifier Possible cause
AC±21
AC±24AC±32
BE±79
AC±39 to 42
AC±45 to 47
AC±45 to 47 Remedy ProblemPage
± AIR CONDITIONING SYSTEMTroubleshooting Refrigeration SystemAC±17

*NOTE at No.6
These gauge indications are shown when the refrigeration system has been opened and the re-
frigerant charged without vacuum purging.
(1)Clean condenser
(2)Check fan motor operation
(3)If (1) and (2) are normal,
check refrigerant amount
HINT: Vent out refrigerant
through gauge manifold low
pressure side by gradually
opening valve.
(1)Replace receiver and drier
(2)Check compressor oil to
see if dirty or insufficient
(3)Vacuum purge and charge
new refrigerant Drier in oversaturated state
Moisture in refrigeration
system freezes at expansion
valve orifice and blocks
circulation of refrigerant(1)Replace receiver and
drier
(2)Remove moisture in cycle
through repeated vacuum
purging
(3)Charge refrigerant to proper
amount
Excess refrigerant in cycle ±
refrigerant overcharged
Condenser cooling
insufficient ± condenser fins
clogged or fan motor faulty Unable to develop
±sufficient performance due to
excessive refrigerant in system
Condenser cooling insufficientMoisture entered in
refrigeration system freeze
at expansion valve orifice
and temporarily stops
cycle, but normal state is
restored after a time when the
ice melts
Pressure too high at both low
and high pressure sides
Frost or large amount of dew
on piping at low pressure side(1)Check heat sensing
tube installed condition
(2)If (1) is normal, test
expansion valve in unit
(3) Replace if defective Pressure low at both low and
high pressure sides
Bubbles seen in sight glass
Insufficient cooling
performance
Air present in refrigeration
system
Insufficient vacuum
purging During operation, pressure at
low pressure side sometimes
becomes a vacuum and
sometimes normal
Trouble in expansion valve
or heat sensing tube not
installed correctly
Refrigerant flow out Pressure low at both low and
high pressure sides
Frost on tubes from
receiver to unit(1)Check with leak tester
and repair
(2)Charge refrigerant to
proper amount
Excess refrigerant in low
pressure piping
Expansion valve opened too
wideInsufficient refrigerant in
system
Refrigerant leaking
Pressure too high at both low
and high pressure sidesPressure too high at both
tow and high pressure sidesGas leakage at some place i n
refrigeration system
Refrigerant flow
obstructed by dirt in
receiver
Air entered refrigeration
system Symptom seen in
refrigeration system
Receiver clogged Replace receiver Probable causeDiagnosis
Remedy
No.
± AIR CONDITIONING SYSTEMTroubleshootingAC±19

COMPRESSOR
ON±VEHICLE INSPECTION
1. INSTALL MANIFOLD GAUGE SET
(See page AC±23)
2. RUN ENGINE AT APPROX. 1,500 RPM
3. CHECK COMPRESSOR FOR FOLLOWING:
(1) High pressure gauge reading is not lower and low
pressure gauge reading is not higher than normal.
(b) Metallic sound
(e) Leakage from shaft seal
If defects are found, repair the compressor.
4. CHECK MAGNETIC CLUTCH
(a) Inspect the pressure plate, and the rotor for signs of
oil.
(b) Check the clutch bearings for noise and grease leak-
age.
(e) Using an ohmmeter, measure the resistance of the
stator coil between the clutch lead wire and ground.
Standard resistance: 3.4 ± 3.8
at 20°C (68°F)
If resistance value is not as specified, replace the coil.
(d) Connect the positive (+) lead from the battery to ter-
minal 1, check that the magnetic clutch is energized.
If magnetic clutch is not energized, replace the coil.
NOTICE: Do not short positive (+) lead wire on the vehicle
by applying battery voltage.
Installation of Manifold Gauge Set
1. CLOSE BOTH HAND VALVES OF MANIFOLD GAUGE
SET
2. INSTALL CHARGING HOSES OF GAUGE SET TO
CHARGING VALVES
Connect the low pressure hose to the low pressure charg-
ing valve and the high ..pressure hose to the high pres-
sure charging valve. Tighten the hose nuts by hand.
HINT Do not apply compressor oil to the seat of the con-
nection.
± AIR CONDITIONING SYSTEMRefrigeration SystemAC±23

COMPRESSOR
ON±VEHICLE INSPECTION
1. INSTALL MANIFOLD GAUGE SET
(See page AC±23)
2. RUN ENGINE AT APPROX. 1,500 RPM
3. CHECK COMPRESSOR FOR FOLLOWING:
(1) High pressure gauge reading is not lower and low
pressure gauge reading is not higher than normal.
(b) Metallic sound
(e) Leakage from shaft seal
If defects are found, repair the compressor.
4. CHECK MAGNETIC CLUTCH
(a) Inspect the pressure plate, and the rotor for signs of
oil.
(b) Check the clutch bearings for noise and grease leak-
age.
(e) Using an ohmmeter, measure the resistance of the
stator coil between the clutch lead wire and ground.
Standard resistance: 3.4 ± 3.8
at 20°C (68°F)
If resistance value is not as specified, replace the coil.
(d) Connect the positive (+) lead from the battery to ter-
minal 1, check that the magnetic clutch is energized.
If magnetic clutch is not energized, replace the coil.
NOTICE: Do not short positive (+) lead wire on the vehicle
by applying battery voltage.
Installation of Manifold Gauge Set
1. CLOSE BOTH HAND VALVES OF MANIFOLD GAUGE
SET
2. INSTALL CHARGING HOSES OF GAUGE SET TO
CHARGING VALVES
Connect the low pressure hose to the low pressure charg-
ing valve and the high ..pressure hose to the high pres-
sure charging valve. Tighten the hose nuts by hand.
HINT Do not apply compressor oil to the seat of the con-
nection.
± AIR CONDITIONING SYSTEMCompressorAC±23

RECEIVER
(See page AC±12)
ON±VEHICLE INSPECTION
CHECK SIGHT GLASS, FUSIBLE PLUG AND FITTINGS FOR
LEAKAGE
Use a gas leak tester. Repair as necessary.
REMOVAL OF RECEIVER
1. DISCHARGE REFRIGERATION SYSTEM
2. REMOVE BATTERY, RESERVE TANK AND IGNITOR
BRACKET
3. DISCONNECT TWO LIQUID TUBES FROM RECEIVER
HINT: Cap the open fittings immediately to keep moisture out of
the system.
4. REMOVE RECEIVER FROM RECEIVER HOLDER
INSTALLATION OF RECEIVER
1. INSTALL RECEIVER IN RECEIVER HOLDER
HINT: Do not remove the blind plugs until ready for connection.
2. CONNECT TWO LIQUID TUBES TO RECEIVER
Torque: 55 kg±cm (48 in.±Ib, 5.4 N±m)
3. REINSTALL IGNITOR BRACKET, RESERVE TANK AND
BATTERY
4. IF RECEIVER WAS REPLACED, ADD COMPRESSOR
OIL TO COMPRESSOR
Add 20 cc (0.7 fl.oz.)
Compressor oil: DENSOOIL 6,
SUNISO NO. 5GS or equivalent
5. EVACUATE AIR FROM AIR CONDITIONING SYSTEM
6. CHARGE AND CONDITIONING SYSTEM WITH
REFRIGERANT AND CHECK FOR GAS LEAKAGE
Specified amount: 600 ± 750 g (1.3 ± 1.7 Ib)
± AIR CONDITIONING SYSTEMReceiverAC±32

CONDENSER
(See page AC±12)
ON±VEHICLE INSPECTION
1. CHECK CONDENSER FINES FOR BLOCKAGE OR
DAMAGE
If the fins are clogged, wash them with water and dry with
compressed air.
NOTICE: Be careful not to damage the fins.
If the fins are bent, straighten them with a screwdriver or pliers.
2. CHECK CONDENSER FITTINGS FOR LEAKAGE
Repair as necessary.
REMOVAL OF CONDENSER
1. DISCHARGE REFRIGERATION SYSTEM
2. REMOVE BATTERY, IGNITOR BRACKET RADIATOR
FAN, CONDENSER FAN
3. DISCONNECT LIQUID TUBE AND DISCHARGE HOSE
FROM CONDENSER FITTINGS
HINT: Cap the open fittings immediately to keep moisture
out of the system.
4. REMOVE CONDENSER
Remove four brackets and four bolts.
INSTALLATION OF CONDENSER
(See page AC±12)
1. INSTALL CONDENSER
Install the brackets and bolts, making sure the rubber cush-
ions fit on the mounting flanges correctly.
2. CONNECT LIQUID TUBE, DISCHARGE HOSE TO
CONDENSER
Torque:
Liquid tube 130 kg±cm (9 ft±Ib, 13 N±m)
Discharge hose 130 kg±cm (9 ft±Ib, 13 N±m)
3. REINSTALL CONDENSER FAN, RADIATOR FAN
IGNITOR BRACKET AND BA¿¿ERY
4. IF CONDENSER WAS REPLACED, ADD
COMPRESSOR OIL TO COMPRESSOR
Add 40 ± 50 cc (1.4 ± 1.7 fl.oz.)
Compressor oil: DENSOOIL 6,
SUNISO NO. 5GS or equivalent
5. EVACUATE AIR FROM AIR CONDITIONING SYSTEM
6. CHARGE AIR CONDITIONING SYSTEM WITH
REFRIGERANT AND CHECK FOR GAS LEAKAGE
Specified amount: 600 ± 750 g (1.3 ± 1.7 Ib)
± AIR CONDITIONING SYSTEMCondenserAC±33

4. INSTALL GROMMETS ON INLET AND OUTLET
FITTINGS
5. CONNECT LIQUID TUBE TO COOLING UNIT INLET
FITTING
Torque the nut.
Torque: 140 kg±cm (10 ft±Ib, 14 N±m)
6. CONNECT SUCTION TUBE TO COOLING UNIT
OUTLET FITTING
Torque the nut.
Torque: 330 kg±cm (24 ft±ib, 32 N±m)
7. IF EVAPORATOR WAS REPLACED, ADD
COMPRESSOR OIL TO COMPRESSOR
Add 40 ± 50 cc (1.4 ± 1.7 fl.oz.)
Compressor oil: DENSOOIL 6,
SUNISO NO. 5GS or equivalent
8. CONNECT NEGATIVE CABLE TO BATTERY
9. EVACUATE AIR FROM AIR CONDITIONING SYSTEM
10. CHARGE AIR CONDITIONING SYSTEM WITH
REFRIGERANT AND CHECK FOR GAS LEAKAGE
Specified amount: 600 ± 700 g (1.3 ± 1.7 Ib)
REFRIGERANT LINES
(See page AC±12)
1. INSPECT HOSES AND TUBES FOR LEAKAGE
Use a gas leak detector. Replace, if necessary.
2. CHECK THAT HOSE AND TUBE CLAMPS ARE NOT
LOOSE
Tighten or replace as necessary.
REPLACEMENT OF REFRIGERANT
LINES
1. DISCHARGE REFRIGERATION SYSTEM
2. REPLACE FAULTY TUBE OR HOSE
HINT: Cap the open fitting immediately to keep moisture
out of the system.
3. TIGHTENING TORQUE FOR O±RING AND BOLTED
TYPE FITTINGS
(See page AC±12)
4. EVACUATE AIR FROM AIR CONDITIONING SYSTEM
5. CHARGE AIR CONDITIONING SYSTEM WITH
REFRIGERANT AND CHECK FOR GAS LEAKAGE
Specified amount: 600 ± 750 g (1.3 ± 1.7 Ib)
± AIR CONDITIONING SYSTEMCooling UnitAC±42