1969 FORD MUSTANG wheel

05-02-04
General Clutch Service

05-02-04

CLEANING AND INSPECTION

RELEASE BEARING

Wipe all oil and dirt off the release

bearing. The bearing is prelubricated

and should not be cleaned with sol-

vent.

Inspect the bearing retainer for

loose spring clips and rivets.

Inspect the release bearing assembly

for burrs which may cause the assem-

bly to drag on the transmission bear-

ing retainer. Any such burrs should be

cleaned up with fine crocus cloth. If

burrs are found, inspect the transmis-

sion input shaft bearing retainer for

evidence of scoring. Any scoring

should be polished out with crocus

cloth. Coat the bearing retainer with a

thin film of lithium-base grease

(C3VY-19586-A). Prior to release

bearing installation, apply a light film

of lithium base grease (C3VY-

19586-A) on both sides of the release

lever fork where it contacts the release

bearing hub and retaining springs.

Apply a light film of lithium base

grease (C3VY-19586-A) plate to the

release bearing surface that contacts

the pressure plate fingers. Carefully

fill the grease groove inside the bear-

ing hub with lithium base grease (no

polyethylene). Clean all excess grease

from the bore of the bearing hub. Ex-

cess grease will be forced onto the

spline by the transmission input shaft

bearing retainer and will contaminate

the clutch disc. Also, care must be

exercised when applying lubricants to

the release bearing, release bearing

hub and the release lever fork to avoid

excessive grease from contaminating

the clutch disc.

Hold the bearing inner race and ro-

tate the outer race while applying

pressure to it. If the bearing rotation

is rough or noisy, replace the bearing.

Most release bearing failures are

caused by improper clutch pedal ad-

justments. If the clutch linkage does

not have enough free travel, the re-

lease bearing will constantly touch the

release fingers and will spin whenever

the engine is running.

When installing a release bearing on

vehicles equipped with separate hub

and bearing, use the tool shown in

Fig. 5.

Release bearing failure can be

caused by the release lever contact

points being out of plane. Check the

wear on the release bearing assembly

where the release lever contacts it.

If one side of the assembly shows

more wear than the other, the release
lever is bent out of plane, or is not

centering on the bracket on the fly-

wheel housing.

Misalignment between the engine

and transmission can cause release

bearing failure. Other symptoms of

misalignment are transmission jump-

ing out of gear, especially third gear,

drive line vibration; excessive wear in

the pilot bushing, excessive clutch disc

spin time resulting in gear clash, and

excessive transmission gear wear.

PRESSURE PLATE AND COVER

Inspect the surface of the pressure

plate for burn marks, scores, or rid-

ges.
Generally, pressure plate resur-

facing is not recommended. However

minor burn marks, scores, or ridges

may be removed. During the resurfac-

ing process, the flatness of the pres-

sure plate must be maintained. If the

pressure plate is badly heat-checked or

deeply scored, replace the pressure

plate and cover assembly. Clean pres-

sure plate and flywheel surfaces with a

suitable solvent, such as alcohol to be

sure the surfaces are free from any oil

film. Do not use cleaners with petrole-

um base, and do not immerse the

pressure plate in the solvent.

Place the plate on the floor, being

careful not to score or scratch the sur-

face.
Force each individual finger

down, then release quickly. If the fin-

ger does not return quickly, a binding

condition is indicated, and the pres-

sure plate should be replaced.

The pressure plate should be lubri-

cated with a lithium-base grease be-

tween the driving lugs and the edges

of the pressure plate openings, as

shown in Fig. 6. Depress the pressure

plate fingers fully, apply the lubricant,

and then move the fingers up and

down until the lubricant is worked in.

Do not apply excessive lubricant.

CLUTCH DISC

Inspect the clutch disc facings for

oil or grease. Eliminate the source of

any oil or grease before replacing the

disc. An excessive amount of grease in

the pilot bushing or release bearing

hub will find its way to the disc fac-

ings.
Too much lubricant in the trans-

mission or a plugged transmission

vent will force the transmission lubri-

cant out the input shaft and onto the

disc facings. Also, rear main bearing

oil seal leaks or oil leaks from the fly-

wheel mounting bolts can contaminate

the clutch disc.
Inspect the clutch disc for worn or

loose facings. Check the disc for worn

or loose facings. Check the disc for

distortion and for loose rivets at the

hub.
Check for broken springs.

Springs loose enough to rattle will not

cause noise when the car is operating.

Replace the disc assembly if any of

these defects are present. Be especially

careful when installing a new disc to

avoid dropping it or contaminating it

with oil or grease.

PILOT BUSHING

Check the fit of the clutch pilot

bushing in the bore of the crankshaft.

The bushing is pressed into the

crankshaft and should not be loose.

Inspect the inner surface of the bush-

ing for wear or a bell-mouthed condi-

tion. If the bushing is worn or dam-

aged, replace the bushing with a new

service bearing. Refer to the applica-

ble engine for the replacement proce-

dure.

C 1785-A

FIG. 5—Installing Clutch Release

Bearing on Hub

PRESSURE PLATE

AND COVER

DRIVING

LUG
FLYWHEEL

C2048-A

FIG. 6—Pressure Plate Lubrication

Pointsprocarmanuals.com

05-03-05
Clutch

05-03-05

4.
Remove the bolt that secures the

left air vent control cable bracket to

the instrument panel. Position the

control cable to one side.

5.
Remove the retaining clip and

flat washer from the clutch pedal

shaft. Then, remove the shaft, bush-

ing, clutch pedal and brake pedal

from the support.

6. Remove the bushings from the

pedal shaft, and transfer the pedal

pad.

7.
Lubricate the clutch pedal shaft

bushings and position them on the

shaft. Then, position the brake pedal

and clutch pedal in the pedal support.

8. Install the flat washer and re-

taining clip on the pedal shaft.

9. Position the assist spring to the

pedal and bracket. Pry the bracket

forward and install the lower bolt.

Torque the bolts to specifications.

10.
Position the master cylinder

push rod, bushing, and washers on the

brake pedal and secure with a retain-

ing clip.

11.
Connect the equalizer rod to

the clutch pedal and secure it in place

with a retaining clip.

12.
Position the air vent control

cable bracket to the instrument panel

and secure with the attaching bolt.

13.
Adjust the clutch pedal free

travel.

EQUALIZER BAR AND/OR

BUSHING REMOVAL AND

INSTALLATION

FORD, MERCURY

AND METEOR

1.
Raise the vehicle and disconnect

the clutch pedal-to-equalizer rod at

the equalizer bar (Fig. 1).

2.
Disconnect the return spring and

retaining spring at the release lever.

Separate the release lever rod from

the release lever.

3.
Remove the equalizer bar frame

bracket from the frame.

4.
Remove the equalizer bar from

the pivot on the flywheel housing.

5.
Remove the wire clip to replace

the outer bushing and the snap ring
from the inner pivot stud to replace

the inner bushing.

6. Position the flat washer, felt

washer and bushing on the inner and

outer pivots. Secure these parts with

the snap ring.

7.
Position the equalizer bar on the

inner pivot and bolt the equalizer bar

frame bracket to the frame. Torque

the attaching bolts to specification.

8. Install the clutch release rod, re-

turn spring and retaining spring.

9. Connect the clutch pedal rod to

the equalizer bar.

10.
Adjust the clutch pedal free

travel.

MUSTANG, COUGAR,

MONTEGO, FALCON,

FAIRLANE (EXCEPT

MONTEGO AND FAIRLANE

WITH 390 V-8)

1.
Disconnect the clutch pedal

equalizer rod at the equalizer bar

(Figs.
2 and 3).

2.
Raise the vehicle and disconnect

the release lever, return spring at the

lever.

3.
Remove the equalizer bar outer

bracket and bushing assembly.

4.
Remove the release rod from the

equalizer bar, and then remove the

equalizer bar. Remove the bushing

and washers from the inner mounting

stud.

5.
Position the equalizer bar, wash-

ers,
inner bushing, and retainer on the

inner stud.

6. After positioning the outer bush-

ing, install the outer bracket (with the

equalizer bar in place).

7.
Connect the release rod and the

release lever return spring.

8. Lower the vehicle. Connect the

clutch pedal equalizer rod to the

equalizer baY and secure with the re-

taining pin.

9. Adjust the clutch pedal free trav-

el as required.

MONTEGO AND

FAIRLANE—390 V-8

1.
Disconnect the clutch pedal
equalizer rod at the equalizer bar (Fig.

2).

2.
Raise the vehicle and disconnect

the return spring at the release lever.

Disconnect the release lever rod from

the equalizer lever.

3.
Remove the equalizer bar center

bolt.

4.
Separate the equalizer bar and

remove both sections from the vehicle.

5.
Remove the bolts retaining the

equalizer bar inner bracket to the fly-

wheel housing and remove the bracket

and bushing assembly.

6. Remove the equalizer bar outer

bracket and bushing assembly.

7.
Remove the snap ring, bushing,

and felt washer from each bracket as-

sembly.

8. Position a felt washer, and bush-

ing on each bracket assembly and se-

cure with the snap ring.

9. Install the outer bracket and

bushing assembly to the frame (Fig.

2).
Torque the bracket attaching bolts

to specifications.

10.
Position the outer section of the

equalizer bar on the outer bracket

pivot.

11.
Connect the two sections of the

equalizer bar. Insert the inner bracket

pivot into the equalizer bar and install

the assembly to the flywheel housing.

Torque the attaching bolts to specifi-

cations.

12.
Install the equalizer bar center

bolt and torque to specifications.

Make sure that both ends of the

equalizer bar are against the felt

washers.

13.
Connect the release rod and the

release lever return spring.

14.
Adjust the clutch pedal free

travel.

15.
Lower the vehicle. Connect the

clutch pedal equalizer rod to the

equalizer bar and secure with the re-

taining clip.

16.
Check the free travel at the

pedal for conformance to specifica-

tions.
Readjust if necessary.

REMOVAL AND INSTALLATION

CLUTCH REMOVAL

1.
Raise the vehicle on a hoist.

2.
Disconnect the drive shaft from

the rear U-joint flange. Then, slide the

drive shaft off the transmission output

shaft. Insert the appropriate tool over

the output shaft and into the extension

housing oil seal.
3.
Disconnect the speedometer

cable from the extension housing.

4.
Disconnect the gear shift rods

from the transmission. If the vehicle is

equipped with a four-speed transmis-

sion, remove the bolts that secure the

four-speed transmission, disconnect

the front brake cable from the cross-

member and remove the crossmem-
member from the vehicle.

5.
Remove the bolts that attach the

transmission to the flywheel housing.

6. Move the transmission rearward

until the input shaft clears the fly-

wheel housing, then remove it from

the vehicle.

7.
Disconnect the clutch release

lever retaining spring from the release

lever.procarmanuals.com

05-03-06
Clutch

05-03-06

8. Remove the starter cable then

remove the starter motor from the fly-

wheel housing.

9. Remove the bolts that secure the

engine rear plate to the front lower

part of the flywheel housing.

10.
Remove the flywheel housing

lower cover (390 CID housing only).

11.
Remove the bolts that attach

the housing to the cylinder block.

12.
Move the housing back just far

enough to clear the pressure plate,

then move it to the right to free the

pivot from the clutch equalizer bar. Be

careful not to disturb the linkage and

assist spring.

13.
Loosen the six pressure plate

cover attaching bolts evenly to release

the spring tension. If the same pres-

sure plate and cover is to be installed

after the clutch is overhauled, mark

the cover and flywheel so that the

pressure plate can be installed in the

same position.

14.
Remove the pressure plate and

the clutch disc from the flywheel.

CLUTCH INSTALLATION

1.
Install the clutch release lever if

it was removed.

2.
Place the clutch disc, and pres-

sure plate assembly in position on the

flywheel. Start the cover attaching

bolts to hold the pieces in place, but

do not tighten them. Avoid touching

the clutch disc facing, dropping the

parts or contaminating them with oil

or grease as clutch chatter may result.

3.
Align the clutch disc with the

tool shown in Fig. 7, and alternately

tighten the bolts a few turns at a time

until they are all tight. Then torque

the six pressure plate cover attaching

bolts to specification before removing

the tool.
4.
Apply a light film of grease

(C3VY-19586-A) to the outside diam-

eter of the transmission front bearing

retainer. Apply a light film of grease

(C3VY-19586-A) to both sides of the

release lever fork where it contacts the

release bearing bore spring clips.

Apply a light film of grease to the re-

lease bearing surface that contacts the

pressure plate release fingers. Fill the

grease groove of the release bearing

hub with lithium base grease (C3VY-

19586-A). Clean all excess grease

from inside the bore of bearing hub.

Excess grease will be forced onto the

spline by the transmission input shaft

bearing retainer and will contaminate

the clutch disc. Also, place the release

bearing and hub on the release lever.

5.
Make certain that the flywheel

housing and the cylinder block mount-

ing surfaces are clean. Position the

felt washer on the pivot in the fly-

wheel housing. Slip the pivot into the

clutch equalizer shaft being careful

not to disturb the linkage and at the

same time position the housing on the

dowels in the cylinder block. Install

and torque the attaching bolts to spec-

ification.

6. Install the starting motor and

connect the cable.

7.
The mounting surfaces of the

transmission and the flywheel housing

must be free of dirt, paint, and burrs.

Install two guide pins in the flywheel

housing lower mounting bolt holes.

Move the transmission forward on the

guide pins until it is tightly positioned

against the flywheel housing.

8. Install the two upper mounting

bolts.
Then, remove the guide pins

and install the two lower mounting

bolts.
Torque all the bolts to specifica-

tion.

9. Raise the rear of the engine and
install the crossmember. Install and

torque the crossmember attaching

bolts to specifications, then lower the

engine.

10.
Install the extension housing-

to-engine rear support attaching bolts.

Torque the bolts to specification.

11.
Remove the transmission jack

and connect the parking brake cable.

12.
If the vehicle is equipped with a

four-speed transmission, connect the

gear shift linkage control bracket to

the extension housing.

13.
Connect the gear shift rods to

the transmission. Adjust the shift link-

age as required.

14.
Connect the release lever retain-

ing spring. Install the flywheel housing

cover (390 CID housing only).

15.
Remove the tool from the

transmission output shaft and install

the drive shaft.

16.
Check the clutch pedal free

travel.

CLUTCH ARBOR CLUTCH DISC

PRESSURE PLATE

C 1788-A

FIG. 7—Installing Clutch Disc —

Typicalprocarmanuals.com

05-04-02

Specifications

05-04-02

TORQUE LIMITS (FT-LBS)

Description

Lower Access Clutch Cover Pan to Flywheel Housing Bolts (Cast Iron Housing)

Transmission Assembly to Flywheel Housing Bolts

Pressure Plate and Cover Assembly to Flywheel Attaching Bolts

Clutch Release Equalizer Frame Bracket Bolts

Clutch Pedal Free Travel Adjustment Nut

Flywheel Housing to Cylinder Block Bolts
6-Cylinder

8-Cylinder

Clutch Pedal Assist Spring Bracket to Brake Pedal Support Bracket
Meteor

Ford,
Mercury

17-20

37-42

12-20

15-24

15-20

_

12-17
Mustang,
Cougar

Fairlane, Montego, Falcon

-

-

12-20

15-24

15-20

23-33

40-50

12-17

SPECIAL TOOLS

Tool No.

A-37H

T61L-7657-Aor B

T57L-7657-A

T64P-7657-A
Description

Clutch Disc Aligner-Universal

Transmission Extension Housing Oil Seal

Replacer
Tool No.

CJ91B

T64L-6392-A

T49P-7580-A
Description

Universal Joint Bearing Replacer

Dia-L-lgner Gauge

Clutch Release Bearing Replacerprocarmanuals.com

06-01-02
General Transmission Service

06-01-02

REAR SEAL REPLACEMENT

1.
Remove the drive shaft.

2.
Remove the seal from the exten-

sion housing with the tool shown in

Fig. 2.

3.
Install the new seal in the exten-

sion housing with the tool shown in

Fig. 3.

4.
Install the drive shaft.

.REAR OIL SEAL

Tool-T61L-7657-A

EXTENSION HOUSING

C 1830.A

FIG. 3—Installing Extension

Housing Seal
Too/-7J75-AB

Tool-TSOT-lOO-A

FIG. 2—Removing Extension Housing Seal

EXTENSION HOUSING

Tool-T52L-7000-GAE

or 7000-G

C1O28-D

FIG. 4—Removing Extension

Housing Bushing and Seal
EXTENSION HOUSING
D
1927. A

Tool—T57P-7697-B

57-G

BUSHING

C 1832.A

FIG. 5—Installing Extension

Housing Bushing

REAR BUSHING AND SEAL

REMOVAL AND INSTALLATION

1.
Remove the drive shaft from the

vehicle.

2.
Insert the tool shown in Fig. 4

into the extension housing until it

grips on ihe front side of the bushing.
3.
Turn the screw clockwise until

the seal and the bushing are free of

the housing.

4.
Drive a new bushing into the ex-

tension housing with the tool shown in

Fig. 5.

5.
Install a new seal in the housing

as shown in Fig. 3.

6. Install the drive shaft.
LUBRICATION

Lubricant level should be even with

the bottom of the filler hole at the

right side of the transmission case.

CLEANING AND INSPECTION

CLEANING

1.
Wash all parts, except the ball

bearings and seals in a suitable clean-

ing solvent. Brush or scrape all foreign

matter from the parts. Be careful not

to damage any parts with the scraper.

Do not clean, wash or soak transmis-

sion seals in cleaning solvents. Dry all

parts with compressed air.

2.
Rotate the ball bearings in a

cleaning solvent until all lubricant is

removed. Hold the bearing assembly

to prevent it from rotating and dry it

with compressed air.

3.
Lubricate the bearings with ap-

proved transmission lubricant and

wrap them in a clean, lint-free cloth

or paper until ready for use.

4.
Clean the magnet welded to the

bottom of the case with kerosene or

mineral spirits.
INSPECTION

1.
Inspect the transmission case for

cracks, worn or damaged bearings

bores,
damaged threads or any other

damage that could affect the opera-

tion of the transmission.

2.
Inspect the front face of the case

for small nicks or burrs that could

cause misalignment of the transmis-

sion with the flywheel housing. Re-

move all small nicks or burrs with a

fine stone.

3.
Replace a cover that is bent or

distorted. Make sure that the vent

hole in the cover is open.

4.
Check the condition of the shift

levers, forks, shift rails and the lever

and shafts.

5.
Examine the ball bearing races

for cracks, wear or roughness. Inspect

the balls for looseness, wear, end play
or other damage. Check the bearings

for looseness in the bores. If any of

these conditions exist, replace the

bearings.

6. Replace roller bearings that are

broken, worn or rough.

7.
Replace the countershaft (clust-

er) gear if the teeth are chipped, brok-

en or worn. Replace the countershaft

if it is bent, scored or worn.

8. Replace the reverse idler gear or

sliding gear if the teeth are chipped,

worn or broken. Replace the idler

gear shaft if bent, worn or scored.

9. Replace the input shaft and gear

if the splines are damaged or if the

teeth are chipped, worn or broken. If

the roller bearing surface in the bore

of the gear is worn or rough, or if the

cone surface is damaged, replace the

gear and the gear rollers.

10.
Replace all other gears that areprocarmanuals.com

06-02-04

Ford Design Three Speed Transmission

06-02-04

shift selector, remove
the
shift selector

assembly from
the
extension housing.

6.
On
Ford, Mercury
and
Meteor

vehicles disconnect
the
parking brake

cable from the equalizer lever and sep-

arate
the
lever from
the
crossmember.

7.
On
Ford, Mercury
and
Meteor

models, remove
the
bolts that secure

the extension housing
to the
engine

rear support.

8. Raise
the
rear
of
the engine high

enough
to
remove
the
weight from
the

crossmember.

9. Support
the
transmission with
a

transmission jack
and
remove
the

transmission from
the
flvwheel hous-

ing.

10.
Move
the
transmission and jack

rearward until
the
input shaft
is
clear

of
the
flywheel housing.

11.
Remove
the
transmission from

the jack
and
mount
it in a
holding

fixture.

Do
not
depress
the
clutch pedal

while
the
transmission
is
removed.

INSTALLATION

1.
Make certain that
the
machined

surfaces
of the
transmission case
and

the flywheel housing
are
free
of
dirt,

paint,
and
burrs.
2.
Install
a
guide
pin in
each lower

mounting bolt hole.

3.
Start
the
input shaft through
the

release bearing. Align
the
splines
on

the input shaft with
the
splines
in the

clutch disc. Move
the
transmission

forward
on the
guide pins until
the

input shaft pilot enters
the
bearing
or

bushing
in the
crankshaft.
If the

transmission front bearing retainer

binds
up on the
clutch release bearing

hub,
work
the
release bearing lever

until
the hub
slides onto
the
transmis-

sion front bearing retainer. Install
the

two transmission-to-flywheel housing

upper mounting bolts
and
lockwash-

ers.
Remove
the two
guide pins
and

install
the
lower mounting bolts
and

lock washers.

4.
Raise
the
rear
of the
engine high

enough
to
provide clearance
for in-

stalling
the
crossmember. Bolt
the

crossmember assembly
to the
frame

side supports.

5.
On
Ford, Mercury
and
Meteor

models, lower
the
engine until
the ex-

tension housing just contacts
the
rear

support. Align
the
bolt holes
in the

extension housing with those
in the

support. Then lower
the
engine
and

remove the jack. Install the two exten-

sion housing-to-support attaching
bolts
and
lock washers.

6.
On
Ford, Mercury
and
Meteor

models, insert
the
parking brake front

cable
in the
equalizer
and
install
the

equalizer
in the
bracket
on the

crossmember. Secure
the
parking

brake rear cable
to the
equalizer.

7.
On
vehicles equipped with
a

column-mounted gear shift selector,

secure
the
shift rods
to the
shift levers

at
the
transmission.
On
vehicles

equipped with
a
floor-mounted gear

shift selector, attach
the
shift selector

assembly
to the
extension housing.

8. Insert
the
speedometer cable
and

driven gear
in the
extension housing

and secure
it
with
a cap
screw
and

lock washer.

9. Remove
the
tool shown
in
Fig.
2,

Part 6-1, from
the
extension housing.

Align
the
reference marks
and
slide

the front universal joint yoke onto
the

output shaft
and
into
the
extension

housing. Connect
the
rear universal

joint
to the
axle pinion flange
and tor-

que
the
nuts
to
specifications.

10.
Fill
the
transmission
to the

proper level with
the
approved lubri-

cant.

11.
Adjust
the
clutch pedal free

travel
and the
shift linkage
as re-

quired.

MAJOR REPAIR OPERATIONS

DISASSEMBLY

1.
Mount
the
transmission
in a

holding fixture and drain
the
lubricant

by removing
the
drain plug,
if so

equipped,
or the
lower extension hous-

ing bolt.

2.
Remove
the cap
screws that
at-

tach
the
cover
to
the case. Remove
the

COVER
cover
and the
gasket (Fig.
5)
from
the

case.

3.
Remove
a
long spring that
re-

tains
the
detent plug
in the
case (Fig.

9).
Remove
the
detent plug with
a

small magnet.

4.
Remove
the cap
screws
and
lock

washers that attach
the
extension

housing
to
the case. Remove extension

FRONT

BEARING RETAINER

C2069-A
and gasket from
the
case.

5.
Remove
the cap
screws
and
lock

washers that attach
the
front bearing

retainer
to the
case. Remove
the
front

bearing retainer
and
gasket from
the

case.

6. Remove
the
lubricant filler plug

from
the
right side
of the
case. Work-

ing through
the
plug opening, drive

the roll
pin out of the
case
and
coun-

tershaft with
a
1/4-inch
punch
(Fig.

6).

TERSHAFT'
#

PIN

C 1841-A

FIG. 5—Transmission Case
and
Related Parts—Typical
FIG. 6—Removing Countershaft

Roll
Pinprocarmanuals.com

06-03-03
Ford Design Four-Speed Transmission
06-03-03

cable from the equalizer lever and sep-

arate the lever from the crossmember.

5.
Remove the hairpin retainer se-

curing the cable to the transmission

rear support crossmember, and then

pull the cable assembly forward and

out of the crossmember.

6. Remove the retaining clip, flat

washer, and spring washer that se-

cures the shift rods to the shift levers.

7.
Remove the bolts that attach the

shift linkage control bracket to the ex-

tension housing and position the as-

sembly out of the way.

8. Support the engine with a trans-

mission jack and remove the extension

housing-to-engine rear support attach-

ing bolts.

9. Raise the rear of the engine high

enough to remove the weight from the

crossmember. Remove the bolts re-

taining the crossmember to the frame

side supports and remove the

crossmember.

10.
Support the transmission on a

jack and remove the bolts that attach

the transmission to the flywheel hous-

ing.

11.
Move the transmission and jack

rearward until the transmission input

shaft clears the flywheel housing. If

necessary, lower the engine enough to

obtain clearance for transmission re-

moval.

Do not depress the clutch pedal

while the transmission is removed.
INSTALLATION

1.
Make sure that the mounting

surface of the transmission and the

flywheel housing are free of dirt,

paint, and burrs. Install two guide

pins in the flywheel housing lower

mounting bolt holes. Move the trans-

mission forward on the guide pins

until the input shaft splines enter the

clutch hub splines and the case is posi-

tioned against the flywheel housing.

2.
Install the two upper transmis-

sion to flywheel housing, mounting

bolts snug, and then remove the two

guide pins. Install the two lower

mounting bolts. Torque all mounting

bolts to specifications.

3.
Raise the rear of the engine and

install the crossmember. Install and

torque the crossmember attaching

bolts to specifications, then lower the

engine.

4.
With the transmission extension

housing resting on the engine rear

support, install the transmission ex-

tension housing attaching bolts. Tor-

que the bolts to specifications.

5.
Position the shift linkage control

bracket to the extension housing and

install the attaching bolts.

6. Secure each shift rod to its re-

spective lever with the spring washer,

flat washer, and retaining pin.

7.
Guide the parking brake cable

assembly through the hole in the
transmission rear support crossmemb-

er. Secure the cable assembly to the

crossmember with the hair pin retain-

er.

8. Insert the parking brake front

cable in the equalizer and install the

equalizer in the bracket on the

crossmember. Secure the parking

brake rear cable to the equalizer.

9. Connect the speedometer cable

to the extension housing.

10.
Remove the extension housing

installation tool and slide the forward

end of the drive shaft over the trans-

mission output shaft. Connect the

drive shaft to the rear U-joint flange.

11.
Place both forward gear shift

levers and the reverse shift lever in the

neutral position and insert a 1/4 inch

diameter alignment tool in the shift

linkage alignment hole (Fig. 17). It

may be necessary to loosen the adjust-

ment nuts to install the alignment

tool. Adjust the linkage as necessary

and tighten the adjustment nuts to

specifications. Remove the alignment

tool.

12.
Fill the transmission to the

proper level with the specified lubri-

cant.

13.
Lower the car. Check tne shift

and crossover motion for full shift en-

gagement and smooth crossover oper-

ation.

MAJOR REPAIR OPERATIONS

DISASSEMBLY

1.
Mount the transmission in a

holding fixture and drain the lubri-

cant.

2.
Remove the cover attaching

screws from the case. Lift the cover

and gasket from the case.

3.
Remove the long spring that re-

tains the detent plug in the case (Fig.

4).
Remove the detent plug with a

small magnet.

4.
Remove the extension housing

attaching screws and lock washers.

Remove the housing and the gasket.

5.
Remove the input shaft bearing

retainer attaching screws. Slide the re-

tainer off the input shaft.

6. Support the countershaft gear

with a wire hook. Working from the

front of the case, push the counter-

shaft out the rear of the case as shown

in Fig. 3. Lower the countershaft to

the bottom of the case with the wire

hook. Remove the hook.
Tool-T64P-711hA

COUNTERSHAFT

C2073-A

FIG. 3—Removing Countershaft

From Case

7.
Place the first and second-speed

gear shift lever and the reverse shift

lever in the neutral position. Place the

third and fourth-speed gear shift lever

in the third-speed position.

8. Remove the attaching screw

from the third and fourth-speed shift

fork. Tap on the inner end of the shift

rail to unseal the expansion plug from
the front of the case. Then withdraw

the third and fourth-speed shift rail

from the front of the case. Do not

lose the interlock pin from the shift

rail.

9. Remove the set screw from the

first and second-speed shift fork.

Slide the first and second-speed shift

rail out the rear of the case.

10.
Remove the interlock plug and

the detent plug from the top of the

case (Fig. 4) with a magnet.

11.
On some models, remove the

snap ring that secures the speedometer

drive gear to the output shaft. Slide

the gear off the shaft, then remove the

speedometer gear drive ball. On mod-

els equipped with the new design re-

tainers, depress the tang on the speed-

ometer drive gear retaining clip and

slide the speedometer gear off the

shaft. (Fig. 5).

12.
Remove the snap ring that se-

cures the output shaft bearing to the

shaft.procarmanuals.com

06-04-02

Specifications

06-04-02

TORQUE LIMITS(FT-LBS)

Extension Housing Bolts

Input Shaft Bearing Retainer-to-Transmission Case Bolts

Speedometer Cable Retainer-to-Transmission Extension

Transmission-to-Flywheel Housing Bolts

Gearshift Control Levers to Cam and Shaft Assembly Lock Nuts

Transmission Cover Bolts

Filler Plug-to-Case

Drain Plug-to-Case

Shift Fork-to-Shift Rail

Third and Fourth Shift Rail Detent Bolt

Gear Shift Control Assembly
to
Transmission Extension

Shift Selector Levers to Shift Rods

Gear Shift Control Support Bracket
to
Back Plate
3-Speed

Transmissions

42-50

30-36

3.0-4.5

37-42

18-23

14-19

10-20

20-30

10-18

-

8-12

10-20

-
4-Speed

Transmissions

42-50

19-25

3.0-4.5

37-42

18-23

14-19

10-20

20-30

10-18

10-18

8-12

10-20

8-13
® Inch-pounds

SPECIAL TOOLS
SPECIAL TOOLS (Continued)

Tool Numbers

T50T-100A

T59L-100B

Tool-1175AB

T53T-4621-Bor(4621-F)

T57L-4220-A4

T52L-7000-GAE

T63P-7025-A

T64P-7025-B

T53T-4621-C
Description

Impact Hammer-Long

Impact Hammer-Short

Grease Seal Remover

Drive Pinion Bearing Cone

Replacer Front
&
Rear

Differential Side Bearing Cone

Replacer
or
Input Shaft Bearing

Remover

Extension Housing Bushing and

Seal Remover

Output Shaft Bearing Remover

& Replacer

Output Shaft Bearing Remover

& Replacer

Drive Pinion Bearing

Cone Replacer
Tool Numbers

Tool-7025-B

Tool-7025-G

T64P-7111-A

T63P-7111-A

T64P-7140-A

T61L-7657-A

T57P-7697-B

T57P-7657-G

T67P-7341-A
Description

Rear Main Shaft Bearing Removei

Main Shaft Bearing Remover

& Replacer

Cluster Gear Roller Retainer Shaf

Cluster Gear Roller Retainer Shaft

Reverse Idler Shaft Remover

Transmission Extension Housing

Oil Seal Replacer

Extension Housing

Bushing Replacer

Extension Housing

Bushing Replacer

Shift Linkage Grommet

Replacerprocarmanuals.com