1969 FORD MUSTANG lock

05-03-04
Clutch

05-03-04

bushings, position the clutch pedal and

bushings in the pedal support.

8. Install the retaining ring on the

clutch pedal shaft.

9. Position the assist spring in the

pedal support bracket and the assist

spring bracket. Rotate the assist

spring bracket clockwise until the

upper bolt holes line up and install the

bolt. Torque both the upper and lower

bolts to specification.

10.
Check the clutch pedal free

travel and adjust as required.

MUSTANG, COUGAR

1.
Disconnect the battery ground

cable.

2.
Remove the steering column.

Refer to Group 3 of this manual for

the procedure.

3.
Remove the two capscrews re-

taining the master cylinder or booster

to the dash panel. Then remove the

two capscrews retaining the pedal sup-

port bracket to the dash panel.

4.
Working inside the vehicle, dis-

connect the clutch pedal-to-equalizer

rod at the clutch pedal by removing

the retainer and bushing.

5.
Secure the clutch pedal against

the bumper stop with a small C-clamp

as shown in Fig. 6.

6. Disconnect the stop light switch

wires at the connector.

7.
Remove the switch retainer and

slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin.

Then lower the switch away from the

pin.
Remove the master cylinder push

CLUTCH PEDAL ASSIST SPRING
rod, bushing and nylon washer from

the brake pedal pin.

8. Remove the screw retaining the

pedal support bracket to the top inner

cowl bracket (Fig. 6).

9. Remove the two sheet metal

screws retaining the pedal support

bracket to the dash panel.

10.
Remove the two screws retain-

ing the pedal support bracket to the

upper cowl brace and lower the pedal

support bracket away from the steer-

ing column studs.

11.
Remove the pedal support

bracket assembly from the vehicle.

12.
Mount the bracket in a vise.

13.
Remove the small C-clamp se-

curing the clutch pedal to the bumper.

Slowly pivot the pedal away from the

bumper until the assist spring can be

lifted from its seat.

14.
Remove the retainer clip from

the clutch and brake pedal shaft.

Then, remove the clutch pedal and

shaft assembly, brake pedal assembly,

and bushings from the pedal support

bracket.

15.
Apply a coating of SAE 10 en-

gine oil to the bushings and locate all

bushings in their proper places on the

brake and clutch pedal assemblies.

16.
Position the brake pedal to the

pedal support bracket. Install the

clutch and brake pedal shaft through

the pedal support and brake pedal as-

sembly. Install the retainer.

17.
Install the clutch pedal assist

spring and pivot the pedal against its

bumper stop. Secure the pedal against

the bumper with a small C-clamp as

TOP INNER COWL-TO-BRACKET

RETAINING SCREW

C2057-A

FIG.
6—Clutch
Pedal —Mustang and Couga?
shown in Fig. 6.

18.
Position the pedal support

bracket assembly to the dash panel

and to the steering column retainer

studs.

19.
Align the pedal support bracket

holes with the holes in the dash panel

and install the two sheet metal screws.

20.
Install the two capscrews at-

taching the pedal support bracket to

the upper cowl bracket.

21.
Install the screw attaching the

support bracket to the top inner cowl

bracket (Fig. 6).

22.
Install the inner nylon washer,

bushing master cylinder push rod on

the brake pedal pin. Position the stop

light switch so that it straddles the

push rod with the switch slot on the

pedal pin and the switch outer hole

just clearing the pin. Slide the switch

completely onto the pin, and install

the outer nylon washer. Secure with

the self-locking pin.

23.
Connect the stop light switch

wires to the connector and install the

wires to the retaining clip.

24.
Connect the clutch pedal-

to-equalizer rod to the clutch pedal

assembly with the bushing and retain-

er and remove the C-clamp from the

bracket.

25.
Working from the engine side

of the dash panel, install the two cap-

screws attaching the pedal support

bracket to the dash panel. Then install

the two screws attaching the master

cylinder to the dash panel.

26.
Install the steering column.

Refer to Group 3 of this manual for

the procedure.

27.
Adjust the clutch pedal free

travel.

28.
Check the brake pedal free

height and travel measurements

(Group 2).

29.
Connect the battery ground

cable.

CLUTCH PEDAL AND/OR

BUSHING REMOVAL

AND INSTALLATION

MOM EGO, FALCON

FAIRLANF

1.
Remove the retaining clip (Fig.

2) that secures the equalizer rod to the

clutch pedal. Disconnect the rod from

the pedal.

2.
Remove the lower bolt retaining

the assist spring bracket to the pedal

support. Then, loosen the upper

bracket retaining bolt (approximately

4 turns) and disconnect the spring

from the clutch pedal and bracket.

3.
Disconnect the brake pedal push

rod from the brake pedal.procarmanuals.com

05-03-06
Clutch

05-03-06

8. Remove the starter cable then

remove the starter motor from the fly-

wheel housing.

9. Remove the bolts that secure the

engine rear plate to the front lower

part of the flywheel housing.

10.
Remove the flywheel housing

lower cover (390 CID housing only).

11.
Remove the bolts that attach

the housing to the cylinder block.

12.
Move the housing back just far

enough to clear the pressure plate,

then move it to the right to free the

pivot from the clutch equalizer bar. Be

careful not to disturb the linkage and

assist spring.

13.
Loosen the six pressure plate

cover attaching bolts evenly to release

the spring tension. If the same pres-

sure plate and cover is to be installed

after the clutch is overhauled, mark

the cover and flywheel so that the

pressure plate can be installed in the

same position.

14.
Remove the pressure plate and

the clutch disc from the flywheel.

CLUTCH INSTALLATION

1.
Install the clutch release lever if

it was removed.

2.
Place the clutch disc, and pres-

sure plate assembly in position on the

flywheel. Start the cover attaching

bolts to hold the pieces in place, but

do not tighten them. Avoid touching

the clutch disc facing, dropping the

parts or contaminating them with oil

or grease as clutch chatter may result.

3.
Align the clutch disc with the

tool shown in Fig. 7, and alternately

tighten the bolts a few turns at a time

until they are all tight. Then torque

the six pressure plate cover attaching

bolts to specification before removing

the tool.
4.
Apply a light film of grease

(C3VY-19586-A) to the outside diam-

eter of the transmission front bearing

retainer. Apply a light film of grease

(C3VY-19586-A) to both sides of the

release lever fork where it contacts the

release bearing bore spring clips.

Apply a light film of grease to the re-

lease bearing surface that contacts the

pressure plate release fingers. Fill the

grease groove of the release bearing

hub with lithium base grease (C3VY-

19586-A). Clean all excess grease

from inside the bore of bearing hub.

Excess grease will be forced onto the

spline by the transmission input shaft

bearing retainer and will contaminate

the clutch disc. Also, place the release

bearing and hub on the release lever.

5.
Make certain that the flywheel

housing and the cylinder block mount-

ing surfaces are clean. Position the

felt washer on the pivot in the fly-

wheel housing. Slip the pivot into the

clutch equalizer shaft being careful

not to disturb the linkage and at the

same time position the housing on the

dowels in the cylinder block. Install

and torque the attaching bolts to spec-

ification.

6. Install the starting motor and

connect the cable.

7.
The mounting surfaces of the

transmission and the flywheel housing

must be free of dirt, paint, and burrs.

Install two guide pins in the flywheel

housing lower mounting bolt holes.

Move the transmission forward on the

guide pins until it is tightly positioned

against the flywheel housing.

8. Install the two upper mounting

bolts.
Then, remove the guide pins

and install the two lower mounting

bolts.
Torque all the bolts to specifica-

tion.

9. Raise the rear of the engine and
install the crossmember. Install and

torque the crossmember attaching

bolts to specifications, then lower the

engine.

10.
Install the extension housing-

to-engine rear support attaching bolts.

Torque the bolts to specification.

11.
Remove the transmission jack

and connect the parking brake cable.

12.
If the vehicle is equipped with a

four-speed transmission, connect the

gear shift linkage control bracket to

the extension housing.

13.
Connect the gear shift rods to

the transmission. Adjust the shift link-

age as required.

14.
Connect the release lever retain-

ing spring. Install the flywheel housing

cover (390 CID housing only).

15.
Remove the tool from the

transmission output shaft and install

the drive shaft.

16.
Check the clutch pedal free

travel.

CLUTCH ARBOR CLUTCH DISC

PRESSURE PLATE

C 1788-A

FIG. 7—Installing Clutch Disc —

Typicalprocarmanuals.com

05-04-02

Specifications

05-04-02

TORQUE LIMITS (FT-LBS)

Description

Lower Access Clutch Cover Pan to Flywheel Housing Bolts (Cast Iron Housing)

Transmission Assembly to Flywheel Housing Bolts

Pressure Plate and Cover Assembly to Flywheel Attaching Bolts

Clutch Release Equalizer Frame Bracket Bolts

Clutch Pedal Free Travel Adjustment Nut

Flywheel Housing to Cylinder Block Bolts
6-Cylinder

8-Cylinder

Clutch Pedal Assist Spring Bracket to Brake Pedal Support Bracket
Meteor

Ford,
Mercury

17-20

37-42

12-20

15-24

15-20

_

12-17
Mustang,
Cougar

Fairlane, Montego, Falcon

-

-

12-20

15-24

15-20

23-33

40-50

12-17

SPECIAL TOOLS

Tool No.

A-37H

T61L-7657-Aor B

T57L-7657-A

T64P-7657-A
Description

Clutch Disc Aligner-Universal

Transmission Extension Housing Oil Seal

Replacer
Tool No.

CJ91B

T64L-6392-A

T49P-7580-A
Description

Universal Joint Bearing Replacer

Dia-L-lgner Gauge

Clutch Release Bearing Replacerprocarmanuals.com

06-01-02
General Transmission Service

06-01-02

REAR SEAL REPLACEMENT

1.
Remove the drive shaft.

2.
Remove the seal from the exten-

sion housing with the tool shown in

Fig. 2.

3.
Install the new seal in the exten-

sion housing with the tool shown in

Fig. 3.

4.
Install the drive shaft.

.REAR OIL SEAL

Tool-T61L-7657-A

EXTENSION HOUSING

C 1830.A

FIG. 3—Installing Extension

Housing Seal
Too/-7J75-AB

Tool-TSOT-lOO-A

FIG. 2—Removing Extension Housing Seal

EXTENSION HOUSING

Tool-T52L-7000-GAE

or 7000-G

C1O28-D

FIG. 4—Removing Extension

Housing Bushing and Seal
EXTENSION HOUSING
D
1927. A

Tool—T57P-7697-B

57-G

BUSHING

C 1832.A

FIG. 5—Installing Extension

Housing Bushing

REAR BUSHING AND SEAL

REMOVAL AND INSTALLATION

1.
Remove the drive shaft from the

vehicle.

2.
Insert the tool shown in Fig. 4

into the extension housing until it

grips on ihe front side of the bushing.
3.
Turn the screw clockwise until

the seal and the bushing are free of

the housing.

4.
Drive a new bushing into the ex-

tension housing with the tool shown in

Fig. 5.

5.
Install a new seal in the housing

as shown in Fig. 3.

6. Install the drive shaft.
LUBRICATION

Lubricant level should be even with

the bottom of the filler hole at the

right side of the transmission case.

CLEANING AND INSPECTION

CLEANING

1.
Wash all parts, except the ball

bearings and seals in a suitable clean-

ing solvent. Brush or scrape all foreign

matter from the parts. Be careful not

to damage any parts with the scraper.

Do not clean, wash or soak transmis-

sion seals in cleaning solvents. Dry all

parts with compressed air.

2.
Rotate the ball bearings in a

cleaning solvent until all lubricant is

removed. Hold the bearing assembly

to prevent it from rotating and dry it

with compressed air.

3.
Lubricate the bearings with ap-

proved transmission lubricant and

wrap them in a clean, lint-free cloth

or paper until ready for use.

4.
Clean the magnet welded to the

bottom of the case with kerosene or

mineral spirits.
INSPECTION

1.
Inspect the transmission case for

cracks, worn or damaged bearings

bores,
damaged threads or any other

damage that could affect the opera-

tion of the transmission.

2.
Inspect the front face of the case

for small nicks or burrs that could

cause misalignment of the transmis-

sion with the flywheel housing. Re-

move all small nicks or burrs with a

fine stone.

3.
Replace a cover that is bent or

distorted. Make sure that the vent

hole in the cover is open.

4.
Check the condition of the shift

levers, forks, shift rails and the lever

and shafts.

5.
Examine the ball bearing races

for cracks, wear or roughness. Inspect

the balls for looseness, wear, end play
or other damage. Check the bearings

for looseness in the bores. If any of

these conditions exist, replace the

bearings.

6. Replace roller bearings that are

broken, worn or rough.

7.
Replace the countershaft (clust-

er) gear if the teeth are chipped, brok-

en or worn. Replace the countershaft

if it is bent, scored or worn.

8. Replace the reverse idler gear or

sliding gear if the teeth are chipped,

worn or broken. Replace the idler

gear shaft if bent, worn or scored.

9. Replace the input shaft and gear

if the splines are damaged or if the

teeth are chipped, worn or broken. If

the roller bearing surface in the bore

of the gear is worn or rough, or if the

cone surface is damaged, replace the

gear and the gear rollers.

10.
Replace all other gears that areprocarmanuals.com

06-01-03

General Transmission Service

06-01-03

chipped, broken or worn.

11.
Check the synchronizer sleeves

for free movement on their hubs.

Make sure that the alignment marks

(etched marks) are properly indexed.

12.
Inspect the synchronizer block-

ing rings for widened index slots,

rounded clutch teeth and smooth in-

ternal surfaces (must have machined

grooves). With the blocker ring on the
cone,
the distance between the face of

the blocker ring and the clutch teeth

on the gear must not be less than

0.010 inches.

13.
Replace the speedometer drive

gear if the teeth are stripped or dam-

aged. Make certain to install the cor-

rect size replacement gear.

14.
Replace the output shaft if

there is any evidence of wear or if any
of the splines are damaged.

15.
Inspect the bushing and the seal

in the extension housing. Replace

them if they are worn or damaged.

The bushing and/or seal should be re-

placed after the extension housing has

been installed on the transmission.

16.
Replace the seal in the input

shaft bearing retainer.

17.
Replace the seals on the cam

and shafts.procarmanuals.com

06-02-03
Ford Design Three Speed Transmission

06-02-03

STOP
PIN

GROMMET

Tool -
T67P.7347.A

GROMMET

LEVER

CONTROL ROD REMOVAL
^S.
GROMMET INSTALLATION

SET STOP PIN SO THAT THE GROMMET

Tool
-
T67P.734LA
AND
SHIFT ROD ARE PROPERLY SEATED
OMMET—^

SEATED
\

CONTROL ROD INSTALLATION

CONTROL ROD

STOP
PIN

FIG. 4—Removing
or
Installing Shift Linkage Grommet

GEAR SHIFT LINKAGE

ADJUSTMENT—FLOOR MOUNTED

1.
Loosen
the
three shift linkage

adjustment nuts. Install
a 1/4
inch
di-

ameter alignment pin through the con-

trol bracket and lever alignment holes

shown
in Fig. 18.

2.
Tighten
the
three linkage adjust-

ment nuts
and
then remove
the
align-

ment
pin.

3.
Check
the
gear shift lever
for a

smooth crossover.

COLUMN-MOUNTED

SHIFT LINKAGE

GROMMET REMOVAL
AND

INSTALLATION

The column-mounted shift lever
as-
sembly incorporates
an oil
impregnat-

ed plastic grommet
in the
end
of
each

lever
arm. A
special tool T67P-

7341-A
is
required
to
install the grom-

met
in the
shift lever,
and to
install

the shift linkage
rod
into
the
grom-

met. Remove
and
install
the
grommet

as follows:

1.
Place
the
lower
jaw of the
tool

between
the
shift lever
and the
shift

rod.
Position
the
stop
pin
against
the

end
of the
shift
rod
(Fig.
4)
and force

the
rod out of the
grommet. Remove

the grommet from
the
shift lever
by

cutting
off the
large shoulder with
a

sharp knife. The groin met must
be re-

moved from
the
shift lever
and a new

one installed each rime
'he rod is
dis-

connected.

2.
Before installing
a
new grommet,
C 2090-A

adjust
the
stop
pin as
necessary
to

properly install
the
grommet and coat

the outside
of
the grommet with lubri-

cant. Then, place
the
grommet
on the

stop
pin and
force
it
into
the
shift

lever hole. Turn
the
grommeit several

times
to be
sure
it is
properly seated.

3.
Readjust
the
stop
pin to a
length

which
is
sufficient
to
install
the
shift

rod into
the
grommet
(Fig.
4).
If
the

pin height
is not
adjusted,
the
shift

rod
may be
pushed
too far
through

the grommet causing damage
to the

grommet retaining
lip.

4.
With
the pin
height properly
ad-

justed, position
the
shift
rod on the

tool
and
force
the rod
into
the
grom-

met until
the
groove
in the rod
seats

on
the
inner retaining
lip of
the grom-

met.

REMOVAL AND INSTALLATION

REMOVAL

1.
Raise
the
vehicle
on a
hoist.

2.
Mark
the
drive shaft
so
that
it

may
be
installed
in the
same relative

position. Disconnect
the
drive shaft

from
the
rear U-joint flange.

3.
Slide
the
front
of the
drive shaft
out
of the
transmission extension

housing
and off the
output shaft
In-

sert
the
tool shown
in (Fig. 2),
Part

6-1 into the extension housing
to
pre-

vent
the
lubricant from leaking
out of

the transmission.

4.
Remove
the cap
screw
and
lock

washer that secures
the
speedometer
cable retainer
to the
extension hous-

ing. Pull
the
speedometer cable
out of

the extension housing.

5.
On
vehicles equipped with
a

column-mounted gear shift selector,

remove
the
shift rods from
the
shift

levers
at
the transmission. On vehicles

equipped with
a
floor-mounted gearprocarmanuals.com

06-02-04

Ford Design Three Speed Transmission

06-02-04

shift selector, remove
the
shift selector

assembly from
the
extension housing.

6.
On
Ford, Mercury
and
Meteor

vehicles disconnect
the
parking brake

cable from the equalizer lever and sep-

arate
the
lever from
the
crossmember.

7.
On
Ford, Mercury
and
Meteor

models, remove
the
bolts that secure

the extension housing
to the
engine

rear support.

8. Raise
the
rear
of
the engine high

enough
to
remove
the
weight from
the

crossmember.

9. Support
the
transmission with
a

transmission jack
and
remove
the

transmission from
the
flvwheel hous-

ing.

10.
Move
the
transmission and jack

rearward until
the
input shaft
is
clear

of
the
flywheel housing.

11.
Remove
the
transmission from

the jack
and
mount
it in a
holding

fixture.

Do
not
depress
the
clutch pedal

while
the
transmission
is
removed.

INSTALLATION

1.
Make certain that
the
machined

surfaces
of the
transmission case
and

the flywheel housing
are
free
of
dirt,

paint,
and
burrs.
2.
Install
a
guide
pin in
each lower

mounting bolt hole.

3.
Start
the
input shaft through
the

release bearing. Align
the
splines
on

the input shaft with
the
splines
in the

clutch disc. Move
the
transmission

forward
on the
guide pins until
the

input shaft pilot enters
the
bearing
or

bushing
in the
crankshaft.
If the

transmission front bearing retainer

binds
up on the
clutch release bearing

hub,
work
the
release bearing lever

until
the hub
slides onto
the
transmis-

sion front bearing retainer. Install
the

two transmission-to-flywheel housing

upper mounting bolts
and
lockwash-

ers.
Remove
the two
guide pins
and

install
the
lower mounting bolts
and

lock washers.

4.
Raise
the
rear
of the
engine high

enough
to
provide clearance
for in-

stalling
the
crossmember. Bolt
the

crossmember assembly
to the
frame

side supports.

5.
On
Ford, Mercury
and
Meteor

models, lower
the
engine until
the ex-

tension housing just contacts
the
rear

support. Align
the
bolt holes
in the

extension housing with those
in the

support. Then lower
the
engine
and

remove the jack. Install the two exten-

sion housing-to-support attaching
bolts
and
lock washers.

6.
On
Ford, Mercury
and
Meteor

models, insert
the
parking brake front

cable
in the
equalizer
and
install
the

equalizer
in the
bracket
on the

crossmember. Secure
the
parking

brake rear cable
to the
equalizer.

7.
On
vehicles equipped with
a

column-mounted gear shift selector,

secure
the
shift rods
to the
shift levers

at
the
transmission.
On
vehicles

equipped with
a
floor-mounted gear

shift selector, attach
the
shift selector

assembly
to the
extension housing.

8. Insert
the
speedometer cable
and

driven gear
in the
extension housing

and secure
it
with
a cap
screw
and

lock washer.

9. Remove
the
tool shown
in
Fig.
2,

Part 6-1, from
the
extension housing.

Align
the
reference marks
and
slide

the front universal joint yoke onto
the

output shaft
and
into
the
extension

housing. Connect
the
rear universal

joint
to the
axle pinion flange
and tor-

que
the
nuts
to
specifications.

10.
Fill
the
transmission
to the

proper level with
the
approved lubri-

cant.

11.
Adjust
the
clutch pedal free

travel
and the
shift linkage
as re-

quired.

MAJOR REPAIR OPERATIONS

DISASSEMBLY

1.
Mount
the
transmission
in a

holding fixture and drain
the
lubricant

by removing
the
drain plug,
if so

equipped,
or the
lower extension hous-

ing bolt.

2.
Remove
the cap
screws that
at-

tach
the
cover
to
the case. Remove
the

COVER
cover
and the
gasket (Fig.
5)
from
the

case.

3.
Remove
a
long spring that
re-

tains
the
detent plug
in the
case (Fig.

9).
Remove
the
detent plug with
a

small magnet.

4.
Remove
the cap
screws
and
lock

washers that attach
the
extension

housing
to
the case. Remove extension

FRONT

BEARING RETAINER

C2069-A
and gasket from
the
case.

5.
Remove
the cap
screws
and
lock

washers that attach
the
front bearing

retainer
to the
case. Remove
the
front

bearing retainer
and
gasket from
the

case.

6. Remove
the
lubricant filler plug

from
the
right side
of the
case. Work-

ing through
the
plug opening, drive

the roll
pin out of the
case
and
coun-

tershaft with
a
1/4-inch
punch
(Fig.

6).

TERSHAFT'
#

PIN

C 1841-A

FIG. 5—Transmission Case
and
Related Parts—Typical
FIG. 6—Removing Countershaft

Roll
Pinprocarmanuals.com

06-02-05

Ford Design Three Speed Transmission

06-02-05

Dummy

Shaft

FIG. 7—Removing Countershaft

7.
On 6-cylinder vehicles with a

model RAN transmission except

Ford, tap the countershaft from the

rear of the case with a dummy shaft

to remove the expansion plug from

the countershaft bore at the front of

the case.

8. Hold the countershaft gear with

a hook and with the tool shown in

Fig. 7, push the countershaft out the

rear of the case.

The countershaft (cluster) gear and

thrust washers (Fig. 21) can be low-

ered to the bottom of the case. Re-

move the countershaft from the rear

of the case.

9. On some models, remove the

snap ring that secures the speedometer

drive gear on the output shaft. Slide

the speedometer drive gear off the

shaft. Remove the speedometer drive

gear lock ball from the shaft. If the

vehicle is equipped with the new de-

sign retainer, depress the tang on the

speedometer drive gear retaining clip

and slide the gear off the output shaft

(Fig. 10).

10.
Remove the snap ring that re-

tains the output shaft bearing on the
C2070 A

shaft. Remove the bearing from the

case and shaft as shown in Fig. 8.

11.
Place both shift levers in the

neutral (center) position.

12.
Remove the set screw that se-

cures the first and reverse shift fork to

the shift rail. Slide the first and rev-

erse shift rail out through the rear of

the case.

13.
Slide the first and reverse syn-

chronizer forward as far as possible,

and rotate the first and reverse shift

fork upward. Then lift it from the

case.

14.
Move the second and third-

speed shift fork to the second-speed

position to gain access to the set

screw. Remove the set screw from the

fork. Rotate the shift rail 90 degrees

as shown in Fig. 11.

15.
Lift the interlock plug (Fig. 9)

from the case with a magnet.

16.
Tap on the inner end of the sec-

ond and third-speed shift rail to re-

move the expansion plug (Fig. 9) from

the front of the case. Remove the shift

rail.

17.
Remove the second and third-

speed shift rail detent plug and spring

from the detent bore.
18.
Pull the input gear and shaft

forward until the gear contacts the

case,
and then remove the large snap

ring. It is necessary to move the gear

forward to provide clearance when re-

moving the output shaft assembly

from RAT model transmissions. On

all other models, the input shaft and

gear is removed from the front of the

case at this time.

19.
Rotate the second and third-

speed shift fork upward, and lift it

from the case.

20.
Carefully lift the output shaft

assembly out through the top of the

case.

21.
On an RAT model, work the

input shaft bearing and gear back

through the bore in the case and out

through the top. Remove idler gear

shaft, driving from the front of the

case.

22.
Lift the reverse idler gear and

two thrust washer (Fig. 12) from the

case.
Lift the countershaft gear, thrust

washer, and dummy shaft from the

case.

23.
Remove the snap ring from the

front of the output shaft, and slide the

synchronizer and the second-speed

gear (Fig. 13) off the shaft.

24.
Remove the next snap ring and

tabbed thrust washer from the output

shaft. Then slide the first gear and

blocking ring off the shaft.

25.
Remove the next snap ring

from the output shaft. The first and

reverse synchronizer hub is a press fit

on the output shaft. To eliminate the

possibility of damaging the synchro-

nizer assembly, remove the synchro-

nizer hub using an arbor press as

shown in Fig. 21. Do not attempt to

remove or install the hub by hammer-

ing or prying.

C2071-A

FIG. 8—Removing Output Shaft

Bearing
SET SCREW
SCREW

MACHINED SURFACE

2ND AND 3RD SHIFT FORK

EXPANSION PLUG

1ST AND REVERSE

SHIFT RAIL

FIG. 9—Shift Rails and Forks Disassembled
C1798-Aprocarmanuals.com