1967 CHEVROLET CAMARO lock

BRAKES 5-27

CHEVELLE
, CHEVY II AND CAMARO SHOWN

1.
Caliper Belts

2.
Bleeder Valve

3. Caliper Half

4.
Piston Spring
Fig.
39-Caliper Assembly-Exploded View

5. Seal

6. Piston

7. Piston Boot

8. Brake Shoes
9. "O" Ri

10.
Caliper

11.
Retaining Pin

12.
Cotter Pin

caliper. Two retaining pins must be removed on

heavy duty Corvette front calipers. Identify the

inboard and outboard shoe if they are to be reused.

5. Remove the end of brake hose at bracket by re-

moving U-shaped retainer from the hose fitting and

withdrawing the hose from bracket.

6. Remove the caliper assembly from the mounting

bracket by removing two hex head bolts.

Disassembly (Fig. 39)

1.
Clean exterior of caliper with Declene, or equivalent.

On Chevrolet and Corvette front caliper, remove

brake hose.

2.
Separate the caliper halves by removing the two

large hex head bolts. Remove the two small "O"

rings from the cavities around the fluid transfer

holes in the two ends of the caliper halves.

3.
To free the piston boots so that the pistons may be

removed, push the piston down into the caliper

as far as it will go. Insert a screwdriver blade

under the inner edge of the steel ring in the boot,

and using the piston as a fulcrum, pry the boot from

its seat in the caliper
half.
CAUTION: Use care not to puncture seal when

removing pistons from caliper. ' ~

4.
Remove the pistons and piston springs from the

caliper
half.
Remove the boot and seal from their

grooves in the piston.

Cleaning and Inspection

1.
Clean all metal parts using Declene, or equivalent.

Remove all traces of dirt and grease. Do not use

mineral base solvents to clean brake parts.

2.
Using an air hose, blow out all fluid passages in the

caliper halves, making sure that there is no dirt

or foreign material blocking any of these passages.

3.
Discard all rubber parts. Boots, seals, and "O"

rings should be replaced with new service kit parts.

4.
Carefully inspect the piston bores in the caliper

halves. They must be free of scores and pits. A

scored or otherwise damaged bore will cause leaks

and unsatisfactory brake operation. Replace the

caliper half if either bore is damaged to the extent

that polishing with very fine crocus cloth will not

restore it.

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-28

Fig.
40—Installing Piston in Caliper Bore Using

Tool J-22591
Fig.
41—Installing Boot Seal in Caliper Bore

Using Tool J-22592

5.
Check the fit of the piston in the bore using a feeler

gage.
Clearance should be as follows:

2 1/16 inch Bore .0045 to .010

1 7/8 inch Bore .0045 to .010

1 3/8 inch Bore .0035 to .009

If the bore is not damaged, and the clearance exceeds

either of the upper limits, a new piston will be required.

Assembly

1.
Assemble the seal in the groove in the piston which

is closest to the flat end of the piston. The lip on

the seal must face toward the large end of the

piston. Be sure lips are in the piston groove and do

not extend over the step in the end of the groove.

2.
Place the spring in the bottom of the piston bore.

3.
Lubricate the seal with dean brake fluid.

4.
Install the piston assembly in the bore using appli-

cable piston rign compressor Tool J-22639, 22629

or 22591 as shown in Figure 40. Use care not to

damage the seal lip as piston is pressed past the

edge of the bore. .

5.
Assemble the boot in the groove of the piston closest

to the concave end of the piston. The fold in the boot

must face toward the end of the piston with the seal

on it.

6. Depress the pistons and check that they slide

smoothly into the bore until the end of the piston is

flush with the end of the bore. If not, re check piston

assembly and location of the piston spring and the

seal.

7.
Position applicable boot seal installer Tool J-22592,

J-22628, or J-22638 over the piston and seat the

steel boot retaining ring evenly in the counterbore

as shown in Figure 41. The boot retaining ring must

be flush or below the machined face of the caliper.

Any distortion or uneven seating could allow con-

taminating and corrosive elements to enter the bore.
8. Position the t:O}> rings in the small cavities around

the brake fluid transfer holes in both ends of the

outboard caliper halves. Lubricate the hex head

. bolts with Delco Brake Lube or clip in clean brake

fluid. Fit caliper halves together and secure with

bolts.
Refer to torque specifications in rear of

manual for correct torque valves.

Installation

1.
Carefully mount the assembled caliper over the edge

of the disc. Use a putty knife to depress pistons so

that the caliper can be lowered into position on the

disc (fig. 42). Use care to prevent damage to boots

• on the edge of the disc as the caliper is mounted.

2.
Secure the caliper to the mounting bracket with two

hex head bolts. Refer to torque specifications in

rear of manual for correct torque values.

CAUTION: If replacing old shoe assemblies,

be sure to get the shoes in the same position

from which they were removed. New shoe as-

semblies have an arrow printed on the back,

showing the direction of forward disc rotation.

3.
Install the shoe and lining assemblies as outlined in

this section.

4.
On Chevrolet and Corvette front calipers, place a

new copper gasket on the male end of the front

wheel brake hose. On all models, install brake hose

in the calipers. With the wheels straight ahead,

pass the female end of the brake hose through the

support bracket.

5.
Make sure the tube seat is clean and connect the

break line tube nut to the caliper. Tighten securely.

6. Allowing the hose to seek a normal position, without

twist, insert hex of the hose fitting into the 12-point

hole in the support bracket and secure it in place

with the "V"-shaped retainer. Turn the steering

geometry from lock to lock while observing the hose.

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES
5-31

POWER BRAKES

INDEX

General Description 5-31

Maintenance
and"
Adjustments 5-31

Inspection . ... 5_31

Lubrication 5-31

Bleeding Instructions . . . 5.31

Air Cleaner Service . . . , 5.31
Page

Component Replacement 5-31

Power Brake Cylinder ......* 5-31

Removal . . 5-31

Disassembly and Assembly See Overhaul Manual

Installation . . . . 5-31

GENERAL DESCRIPTION

The Power Brake Unit is a self-contained hydraulic

and vacuum unit, utilizing manifold vacuum and atmos-

phere pressure for its power.

This unit permits the use of a low brake pedal as well

as less pedal effort than is required with the conventional

(nonpower) hydraulic brake system. Only two external
line connections are necessary -
one
a vacuum connection

from manifold to check valve located on front shell; the

other, a hydraulic connection from the main cylinder

outlet directly into the hydraulic system. The unit is

mounted on the engine side of the fire wall and directly

connected to the brake pedal.

MAINTENANCE AND ADJUSTMENTS

INSPECTIONS

1.
Check vacuum line and vacuum line connections as

well as vacuum check valve in front shell of power

unit for possible vacuum loss.

2.
Inspect all hydraulic lines and connections at the

wheel cylinders and main cylinder for possible

hydraulic leaks.

3.
Check brake assemblies for scored drums, grease

or brake fluid on linings, worn or glazed linings,

and make necessary adjustments.

4.
Check brake fluid level in the hydraulic reser-

voirs.
The reservoirs should be filled to the levels

shown in Figure 8.

5. Check for loose mounting bolts at main cylinder and

at power section.

6. Check air cleaner filter in power piston extension

and replace filter if necessary.

7. Check brake pedal for binding and misalignment

between pedal
-and
push rod.

LUBRICATION

The power brake unit is lubricated at assembly and
needs no further lubrication other than maintaining

normal reservoir fluid level. The reservoir should be

filled as described in this section.

BLEEDING INSTRUCTIONS

The power system may be bled manually or with a

pressure bleeder as outlined in this section. Use only

GM
Supreme 11 Brake Fluid or equivalent. Do not use the

power assist while bleeding. The engine should not be

running and the vacuum reserve should be reduced to

zero by applying the brake several times before starting

the bleeding procedure.

AIR CLEANER SERVICE

Servicing of the air cleaner is recommended and the

element replaced when restriction becomes severe

enough to affect power brake response. At any other

time, if cleaning of the filter is felt necessary, it should

be shaken free of dirt or washed in soap and water and

thoroughly dried.

COMPONENT REPLACEMENT

POWER BRAKE CYLINDER

Removal

1.
Remove vacuum hose from vacuum check valve.

2.
Disconnect hydraulic lines at main cylinder.

Disconnect push rod at brake pedal assembly.

Remove nuts and lock washers securing power unit

to fire wall, and remove power unit from engine

compartment.
3.

4.

NOTE:
Chevy

to fire wall.
has a three stud attachment

Repair procedures for the power cylinder are outlined

in the Brake Section of the Overhaul Manual-for service
of the main cylinder refer to applicable portion of

"Standard Brakes" in this manual.

Installation

1.
Mount the power brake assembly in place and install

the attaching nuts and lock washers.

2.
Attach vacuum line to check valve.

3.
Secure hydraulic lines to main cylinder.

4.
Attach push rod to brake pedal assembly, and check

operation of stop light.

5. Bleed brakes as outlined in this section.

CAUTION: After replacing the unit on the vehi-

cle,
start the engine and allow vacuum to build

up before applying the brake.

CHEVROLET CHASSIS SERVICE

SECTION 6

ENGINE

CONTENTS
OF
THIS SECTION

Page

Engine Tune Up
6-1
Torque Sequence

Engine Mechanical
(In
Line)
6-12
Special Tools
. .

Engine Mechanical (V8)
6-24
Page

6-39

6-40

ENGINE TUNE UP

INDEX

Page

General Description
. 6-1

Mechanical Checks and Adjustments
6-1

Spark Plug Removal
6-1

Test Compression
6-1

Service and Install Spark Plugs
6-2

Service Ignition System
6-3

Service Battery
and
Battery Cables
6-5

Service Delcotron
and
Regulator
6-5

Service
Fan
Belt
6-5

Service Manifold Heat Valve
6-5

Tighten Manifold
6-5

Service Fuel Lines
and
Fuel Filter ..........
6-6

Service Cooling System
6-6

Check and Adjust Accelerator Linkage
6-6

Service Crankcase Ventilation
6-6

Service
Air
Injection Reactor System
6-6

Choke Adjustment
6-7
Page

Instrument Cheek-Out
6-7

Instrument Hook-Up.
. 6*7

Check and Adjust Dwell
6-7

Check Dwell Variation
6-7

Check and Adjust Timing
6-8

Adjust Idle Speed
and
Mixture
6-8

Additional Checks and Adjustments
. 6-8

Testing Crankcase Ventilation Valve
. 6-8

Testing Cranking Voltage
6-8

Cylinder Balance Test
. 6-8

Battery
6-8

Ignition
; 6-8

Carburetor
6-11

Fuel Pump
6-11

Cooling System
. 6-11

Cylinder Head Torque and Valve Adjustment
..... 6-11

GENERAL DESCRIPTION

The engine tune up
is
important
to the
modern automo-

tive engine with
its
vastly improved power and perform-

ance.
The
higher compression ratios, improved electri-

cal systems
and
other advances
in
design, make today1 s

engines more sensitive
and
have
a
decided effect
on

power, performance and fuel consumption.

It
is
seldom advisable
to
attempt
a
tune up
by
correc-

tion
of one or two
items only. Time will normally
be

saved
and
more lasting results assured
if the
technician

will follow
a
definite
and
thorough procedure
of
analysis

and correction
of all
items affecting power, performance

and economy.

The tune
up
will
be
performed
in
two parts.
The
first

part will consist
of
visual and mechanical checks and
ad-

justments;
the
second part will consist
of
an instrument

checkout that
can be
performed with
any one of the
units
of service equipment available
for
this purpose. Always

follow
the
instructions provided
by the
manufacturer
of

the particular equipment
to be
used.

Additional checks
and
adjustments
are
included
in the

latter part
of
this section
for use as
required. Many
of

these operations
can be
used
to
isolate and correct trou-

ble located during
the
tune up. Where conditions
are
UB-

covered requiring major corrective action, refer
to the

appropriate section
of
this manual
or the
Passenger

Chassis Overhaul Manual
for
detailed service informa-

tion.

Typical illustrations
and
procedures
are
used except

where specific illustrations
or
procedures
are
necessary

to clarify
the
operation. Illustrations showing bench
op-

erations
are
used
for
clarification however
all
operations

can
be
performed
on the
vehicle.

MECHANICAL CHECKS
AND
ADJUSTMENTS

Spark Plug Removal

Remove any foreign matter from around spark plugs
by

blowing
out
with compressed
air,
then disconnect wires

and remove plugs.

Test Compression
(Fig. 1)

The compression check
is
important because
an
engine

with
low or
uneven compression cannot
be
tuned success-
fully.
It is
essential that improper compression
be cor-

rected before proceeding with
the
engine tune
up.

1.
Remove
air
cleaner
and
block throttle
and
choke
in

wide open position.

2.
Hook
up
starter remote control cable
and
insert

compression gauge firmly
in
spark plug port.

CAUTION: Whenever
the
engine
is
cranked

CHEVROLET
C*
IS SERVICE MANUAL

ENGINE
6-3

(ROUND) Y~~fll^H

CENTRIFUGAL
A ^k

ADVANCE--jflgKpl

MECHANISM
UB|

CAM
KSK^2

LUBRICATOR
VlSMi

REPLACEMENT
^BK

-^ADJUST
SQUARELY

AND
JUST

TOUCHING
LOBE

OF
CAM
/ROTOR

HBB
__

I^BH^F
?
(SOUARE)

^K^ I /—
CAM

jKft^J / LUBRICATOR

H^T^
CAUTION!

QV NEVER
OIL

•L-^
CAM LUBRICATOR-

REPLACE
WICK

WHEN
NECESSARY
LATERAL

MISALIGNMENT
PROPER

LATERAL ALIGNMENT

Fig.
4- Distributor (V8)

CAUTION: Use extreme care
-when
using tap to

prevent cross threading. Also crank engine sev-

eral times to blow out any material dislodged

during cleaning operation.

7. Install spark plugs with new gaskets and torque to

specifications.

NOTE:
The following are some of the

greatest causes of unsatisfactory spark plug

performance.

•
Installation of plugs with insufficient torque to

fully seat the gasket.

•
Installation of the plugs using excessive torque

which changes gap settings.

•
Installation of plugs on dirty gasket seal.

•
Installation of plugs into corroded spark plug hole

threads.

8^ Connect spark plug wiring.

Service
Ignition System

1.
Remove distributor cap, clean cap and inspect for

cracks, carbon tracks and burned or corroded ter-

minals. Replace cap where necessary.

2.
Clean rotor and inspect for damage or deterioration.

Replace rotor where necessary.

3.
Replace brittle, oil soaked or damaged spark plug

wires.
Install all wires to proper spark plug. Proper

positioning of spark plug wires in supports is impor-

tant to prevent cross-firing.

4.
Tighten all ignition system connections.

5. Replace or repair any wires that are frayed, loose or

damaged.
Us
CORRECT
LATERAL MISALIGNMENT BY

j BENDING
FIXED CONTACT SUPPORT

[NEVER
BEND BREAKER LEVER

Fig.
5 - Point Alignment

Magnetic
Pulse(Breakerless)
Distributor

There are no moving parts in the ignition pulse ampli-

fier, and the distributor shaft and bushings have perma-

nent type lubrication, therefore no periodic maintenance

is required for the magnetic pulse ignition system. Refer

to Section 6Y for an analysis of problems and/or repair

procedures encountered on the Transistorized (Magnetic

Pulse) ignition system.

Standard
(Breaker Point) Distributor
(Figs.
3 or 4)

1.
Check the distributor centrifugal advance mechanism

by turning the distributor rotor in a clockwise direc-

tion as far as possible, then releasing the rotor to

see if the springs return it to its retarded position.

If the rotor does not return readily, the distributor

must be disassembled and the cause of the trouble

corrected.

2.
Check to see that the vacuum spark control operates

freely by turning the movable breaker plate counter-

clockwise to see if the spring returns to its retarded

position. Any stiffness in the operation of the spark

control will affect the ignition timing. Correct any

interference or binding condition noted.

3.
Examine distributor points and clean or replace if

riecessary.

DO
NOT SUCK

IN
TOO MUCH

ELECTROLYTE

TAKE
READING

AT
EYE LEVEL

Fig.
6 - Testing Specific Gravity of Battery

CHEVROtET
CHASSIS SERVICE MANUAL

ENGINE 6-4

• Contact points with an overall gray color and only

slight roughness or pitting need not be replaced.

• Dirty points should be cleaned with a clean point

file.

Use only a few strokes of a clean, fine-cut con-

tact file. The file should not be used on other

metals and should not be allowed to become

greasy or dirty. Never use emery cloth or sand-

paper to clean contact points since particles will

embed and cause arcing and rapid burning of

points. Do not attempt to remove all roughness

nor dress the point surfaces down smooth.

Merely remove scale or dirt.

• Clean cam lobe with cleaning solvent, lubricate

cam lobe with "Delco Remy Cam and Ball Bearing

Lubricant" or its equivalent and rotate cam lubri-

cator wick 1/2 turn.

• Replace points that are burned or badly pitted.

NOTE: Where prematurely burned or badly

pitted points are encountered, the ignition sys-

tem and engine should be checked to determine

the cause of trouble so it can be eliminated.

Unless the condition causing point burning or

pitting is corrected, new points will provide no .

better service than the old points. Refer to

Section 6Y for an analysis of point burning or

pitting.

• Check point alignment (fig. 5) then, adjust distri-

. butor contact point gap to .019" (new points) or

.016"
(used points). Breaker arm rubbing block

must be on high point of lobe during adjustment.

NOTE: If contact points have been in service,

they should be cleaned with a point file before

adjusting with a feeler gauge.

• Check distributor point spring tension (contact
Fig. 8 - Manifold Heat Control Valve (In Line)

point pressure) with a spring gauge hooked to

breaker lever at the contact and pull exerted at 90

degrees to the breaker lever. The points should

be closed (cam follower between lobes) and the

reading taken just as the points separate. Spring

tension should be 19-23 ounces. If not within

limits,
replace.

Excessive point pressure" will cause excessive

wear on the points, cam and rubber block. Weak

point pressure permits bouncing or chattering,

resulting in arcing and burning of the points and

an ignition miss at high speed.

4.
Install rotor and distributor cap. Press all wires

firmly into cap towers.

Fig. 7 - Checking Fan Belt Tension
Fig. 9 - Manifold Heat Control Valve (V8)

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-7

Tune Up should be checked whenever the Air Injection

Reactor System seems to be malfunctioning. Particular

care should be taken in checking items that affect fuel-air

ratio such as the crankcase ventilation system, the car-

buretor and the carburetor air cleaner. Carburetors and

distributors for engines with the Air Injection Reactor

System are designed, particularly, for these engines;

therefore, they must not be interchanged with or replaced

by a carburetor or distributor designed for an engine

without the Air Injection Reactor System.

Choke Adjustment (Fig. 11)

With Remote Choke

1.
Remove air cleaner and check to see that choke

valve and rod move freely.

2.
Disconnect choke r*od at choke lever.

Check choke adjustment as follows:

On all except 275 hp 327 cu. in. engines, hold

choke valve closed and pull rod up against stop. The

top of choke rod end should be 1/2 - 1 rod diameter
4.

5.
above top of hole in choke valve lever.

On 275 hp 327 cu. in. engines, hold choke valve

closed and push rod down against stop on thermostat

bracket. The top of the choke rod should be 1/2 - 1

rod diameter below the top of the hole in the choke

lever.

If necessary, adjust rod length by bending rod at off-

set. (Bend must be such that rod enters choke lever

hole freely and squarely.)

Connect rod at choke lever and install air cleaner.

3.
With Manual
Choke

1.
Remove air cleaner.

2.
Push hand choke knob in to within 1/8" of instrument

panel.

3.
Loosen choke cable at carburetor bracket and adjust

cable through the clip until the choke valve is wide

open.

4.
Tighten cable clamp at carburetor bracket and check

operation of choke valve to ensure full closed and

wide open positions.

INSTRUMENT CHECK-OUT

Instrument Hook Up

Connect vacuum gauge, dwell meter, tachometer and

timing light as recommended by the manufacturer of the

equipment being used.

Check and Adjust Dwell

1.
Start engine then ch^ck ignition dwell.

.2.
If dwell is not within specifications, adjust dwell as

follows:

V8 ENGINES

• With engine running at idle, raise the adjustment

screw window-and insert an Allen wrench in the

socket of the adjusting screw (fig. 12).

• Turn the adjusting screw as required until a dwell

reading of 30° is obtained. A 2° variation is al-

lowable for wear.

• Close access cover fully to prevent the entry of

dirt into the distributor.

NOTE: If a dwell meter is not available, turn
adjusting screw clockwise until engine starts to

misfire, then turn screw one-half turn in the op-

posite direction to complete adjustment.

IN LINE ENGINES

• Remove distributor cap and recheck point setting.

If dwell is still not within specifications check the

distributor as outlined in Section 6Y.

Check Dwell Variation

Slowly accelerate engine to 1500 rpm and note dwell

reading. Return engine to idle and note dwell reading. If

dwell variation exceeds specifications, check for worn

distributor shaft, worn distributor shaft bushing or loose

breaker plate.

WINDOW

"HEX" TYPE

WRENCH

Fig.
12 - Setting Point Dwell (V8)
Fig.
13 - Ignition Timing Marks

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE
6-8

Check
and
Adjust Ignition Timing
(Fig. 13)

1.
Disconnect
the
distributor spark advance hose
and

plug
the
vacuum source opening.

2.
Start engine
and run at
idle speed
(see
tune
up
chart).

3.
Aim
timing light
at
timing
tab.

NOTE:
- The
markings
on the
tabs
are in 2°

increments
(the
greatest number
of
markings
on

the
"A"
side
of the "O"). the "O"
markings
is

TDC
of
#1 cylinder
and all
BTDC settings fall
on

the
"A"
(advance) side
of "O".

4.
Adjust
the
timing
by
loosening
the
distributor clamp

and
,
rotating
the
distributor body
as
required, then

tighten
the
clamp.

5.
Stop engine
and
remove timing light
and
reconnect

the spark advance hose.

Adjust Idle Speed
and
Mixture
(Fig. 14)
(Except when

equipped with
Air
Injection Reactor System)

1.
As a
preliminary adjustment, turn idle mixture

screws lightly
to
seat
and
back
out 2
turns.

CAUTION:
Do not
turn idle mixture screw

tightly against seat
or
damage
may
result.

2.
With engine running
at
operating temperature (choke

wide open) adjust idle speed screw
to
bring idle

speed
to
specified
rpm
(automatic transmission
in
drive, manual transmission
in
neutral).

3.
Adjust idle mixture screw
to
obtain highest steady

idle speed
(1/4
turn
out
from lean roll).

4.
Repeat Steps
2 and 3 as
needed
for
final adjustment.

5.
Shut down
the
engine, remove gauges
and
install
air

cleaner.

Adjust Idle Speed
and
Mixture
(Fig. 14)
(With
Air

Injection Reactor System)

The recommended adjustment procedure
for Air
Injec-

tion Reactor System equipped engines
is as
follows:

1.
As a
preliminary adjustment, turn idle mixture

screws lightly
to
seat
and
than back
out 3
turns.

CAUTION:
Do not
turn idle mixture screw

tightly against seat
or
damage
may
result.

2.
With engine running
at
operating temperature, choke

wide open,
and
parking brake applied, adjust idle

specified idle speed (automatic

"drive"-manual transmission
in
to

in
screw

transmission

"neutral").

;3.
Adjust idle mixture screw (turn
in) to
"lean roll"

position; then turn screw
out 1/4
turn
(1/4
turn rich

from "lean roll").
The
definition
of
"lean roll" point

is
a 20 to 30 rpm
drop
in
engine speed, obtained
by

leaning
the
idle mixture.

4.
Repeat Steps
2 and 3 as
needed
for
final adjustments.

ADDITIONAL CHECKS
AND
ADJUSTMENTS

Testing Crankcase Ventilation Valve
(Fig. 15) 0

1.
Connect tachometer
and
vacuum gauge
as for
idle

speed
and
mixture adjustment.

2.
Set
parking brake, start engine
and
adjust idle speed

and mixture.

3.
Disconnect ventilation hose
at
valve, block opening
of

valve
and
read engine
rpm
change.

4.
A
change
of
less than
50 rpm
indicates
a
plugged

ventilation valve
-
replace
the
valve.

Cylinder Balance Test
(Fig. 16)

It
is
often difficult
to
locate
a
weak cylinder.
A com-

pression test,
for
example, will
not
locate
a
leaky intake

manifold,
a
valve
not
opening properly
due to a
worn

camshaft,
or a
defective spark plug.

With
the
cylinder balance test,
the
power output
of one

cylinder
may be
checked against another, using
a set of

grounding leads. When
the
power output
of
each cylinder

is
not
equal,
the
engine will lose power
and run
roughly.

Perform
a
cylinder balance test
as
follows:

1.
Connect
the
tachometer
and
vacuum gauge.

2.
Start engine
and run at 1500 rpm.

3.
Ground large clip
of
grounding leads
and
connect
in-

dividual leads
to all
spark plugs except
the
pair being

tested.

Divide
the
firing order
in
half
and
arrange
one
half

over
the
other.
The
cylinders
to be
tested together
ap-

pear
one
over
the
other.

L4 Firing Order
V8 Firing Order

1-8-4-3-6-5-7-2

1-6, 8-5, 4-7, 3-2

1-3-4-2
= 1-3

4-2

L6 Firing Order

1-5-3-6-2-4
=
=
1-4. 3-2

1-5-3

6-2-4
1-6, 5-2, 3-4
1-8-4-3

6-5-7-2

4.
Operate engine
on
each pair
of
cylinders
in
turn
and

note engine
rpm and
manifold vacuum
for
each pair.

A variation
of
more than
1
inch
of
vacuum
or 40 rpm

between pairs
of
cylinders being tested indicates that

the cylinders
are off
balance.

Battery

The battery should
be
checked with special testing

equipment
and to the
equipment manufacturers specifica-

tions.
See
Section 6Y
for
complete information
on
battery

tests.

Ignition

The following additional ignition checks
may be
made

with
any of
several pieces
of
equipment available
for un-

covering
the
source
of
engine difficulties.
The
specific

operating instructions
of the
equipment manufacturer

should
be
followed:

Cranking voltage

Ignition switch

Distributor resistance

Secondary resistance

Ignition output
and
secondary leakage

Cranking Voltage
(Fig. 17)

1.
Disconnect coil primary lead
at the
coil negative

terminal
to
prevent engine from firing during

cranking.

2.
Connect voltmeter between primary terminal
of coi|

(resistance wire side)
and
ground.

3.
Operate starting motor.

CHEVROLET CHASSIS SERVICE MANUAL