1967 CHEVROLET CAMARO lock

REAR SUSPENSION AND DRIVE LINE 4-33

Fig.
84—Drive Pinion Flange Removal

J-21057 for heavy-duty axle, press seal into bore

until it seats against shoulder (figs. 85 and 86).

CAUTION: Pinion oil seal flange must not bot-

tom against "carrier. Press seal into carrier

bore until it seats against internal shoulder -

do not apply unnecessary pressure after seal is

seated. To do so will destroy rubber seat ancl

distort seal. ;

11.
Position and align pinion flange on pinion shaft using

Tools J-9458 and
J-8614-1.
Tool J-9458-1 is

threaded onto pinion shaft and nut tightened against

J-9458-2 to pull flange on shaft (fig. 87). Remove
Fig.
86—Drive Pinion Flange Oil Seal

Installation (Heavy-Duty)

J-9458 after flange is seated.

NOTE: The position of the pinion and flange

was previously marked so that reinstallation

may be made with flange and pinion in same

relative position.

CAUTION: Do not attempt to hammer flange

onto pinion shaft. To do so will damage ring

gear and pinion.

12.

13.

14.

15.
Pack the cavity between end of pinion splines and

pinion flange with a non-hardening sealer (such as

Permatex Type A) prior to installing washer and

nut on pinion.

Install washer and a new self-locking nut on pinion

shaft. Tighten nut to remove end play and continue

alternately tightening in small increments and check-

ing preload with torque wrench until it is the same

as that recorded in Step 4.

Reassemble the rear universal joint, and torque

"V" bolt nuts to specifications.

Lower vehicle to floor and road test for leaks.

Fig.
85—Drive Pinion Flange Oil Seal

Installation (Light-Duty)
Fig.
87—Drive Pinion Flange Installation

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-34

COMPONENT PARTS REPLACEMENT (CORVETTE)

AXLE DRIVESHAFT-FIGURE 88

Removal

1.
Disconnect inboard driveshaft trunnion from side

gear yoke.

2.
Bend bolt lock tabs down and remove four bolts

securing shaft flange to spindle drive flange.

3.
Pry driveshaft out of outboard drive flange pilot

and remove by withdrawing outboard end first (fig.

89).

Repairs

1.
Remove bearing lock ring from trunnion yoke.

2.
Support turnnion yoke on a piece of 1-1/4" pipe on

arbor press bed.

3.
Using suitable socket or rod, press trunnion down

far enough to drive opposite bearing cup from yoke.

4.
Remove trunnion and press other bearing cup from

yoke, being careful not to
drop'
cup
or lose bearing

rollers.

5. Remove trunnion and yoke from other joint in a

similar manner.

3

AXLE
II 1

i

c

DRI\

c

y
'E SHAFT ^

AXLE
v

DRIVE^
SHAFT
•
Fig.
88—Axle Driveshaft
6. Remove dust seals from trunnion, clean and inspect

bearing rollers and trunnion. Relubricate bearings

with a high-melting point wheel bearing type

lubricant.

NOTE:
In addition to packing the bearings,

make sure that the lubricant reservoir at the

end of each trunnion is completely filled with

lubricant. In filling these reservoirs, pack lu-

bricant into the hole so as to fill from the .

bottom. This will prevent air pockets and en-

sure an adequate supply of lubricant.

7. Place new dust seals on trunnion, cavity of seal

toward end of trunnion - then position Tool J-21556

over end of trunnion and into cavity portion of seal.

Press seal onto trunnion until tool bottoms against

trunnion (fig. 90).

NOTE:
Installation of seal is critical to proper

sealing - use specified tool during installation

to prevent seal distortion and to assure proper

seating of seal on trunnion.

8. Partially install one bearing cup into yoke. Place

trunnion in yoke and into bearing cup. Install other

bearing cup and press both bearing cups into yoke,

being careful to keep trunnion aligned in bearing

cups.

9. Press bearing cups far enough to install lock rings,

and install lock rings.

NOTE:
It may be more convenient, if neces-

sary, to use a bench vise for removal and

installation, instead of an arbor press. In this

case, proceed with disassembly and assembly

procedure as with an arbor press.

Installation

1.
Place driveshaft inboard trunnion into side gear

yokes and assemble
"XJ"
bolts. Rotate yokes so that

trunnion seats are phased 90° apart.

2.
Install outboard drive flange into spindle drive flange

pilot, position bolt lock over bolt holes and install

four bolts. Torque bolts to specification and bend

lock tabs flat against bolt heads.

Fig. 89—Removing Driveshaft

Fig.
90—
"U"
Joint Trunnion Seal Installation

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-35

Fig.
91—
Removing Carrier Front Support

PINION FLANGE, DUST DEFLECTOR

AND/OR OIL SEAL

Removal

1.
Raise vehicle and place jackstand under frame to

allow wheels to hang free.

2.
Place 1/2" thick block of wood or steel between

carrier upper surface to rear of companion flange,

and body floor. This will prevent carrier assembly

from twisting upward when front support bracket is

disconnected.

3.
Disconnect carrier front mounting bracket bolt from

frame crossmember.

4.
Remove nut from carrier bracket front bolt and

slide bolt to one side until bolt head contacts floor

well. Mark the floor well at this point and drill a

3/4"
diameter hole - remove bolt.

5. Loosen bracket rear bolt and swing bracket down

and to the rear (fig. 91).

6. Disconnect propeller shaft at transmission and at

companion flange. Slide transmission yoke forward,

and lower propeller shaft down and out.

7. Mark companion flange nut and pinion relative loca-

tion.
This is necessary to reset original pinion

bearing pre-load during reassembly of companion

flange.

8. Attach J-8614-1 companion flange holder and remove

flange nut and washer (fig. 92).

9. Remove companion flange by driving off with brass

drift and hammer (fig. 93).

10.
Using screw driver, pry oil seal out of carrier.

Inspection

Inspect companion flange splines for excessive wear

or twisting and check deflector for looseness. If de-

flector is loose or damaged, break stake marks and

remove. Install new deflector and stake in place.

Installation

1.
Place sealing compound around O.D. of new seal

and install seal in carrier using seal Installer

J-21057 (fig. 94).
Fig.
92—Removing Companion Flange Nut

NOTE:
Seal should be started squarely in bore

to eliminate seal distortion.

2.
Tap seal into position until there is a 1/8" gap be-

tween seal flange and carrier (fig. 95).

3.
Lubricate companion flange splines and tap into

place.

4.
Install companion flange washer and nut, and tighten

nut so that it lines up with mark on pinion.

5. Raise propeller shaft into position and connect to

companion flange and transmission yoke.

6. Place rubber cushion on carrier front mounting

bracket and raise bracket into position and loosely

install nut.

7. Install carrier bracket front bolt. With vehicle at

curb,
torque all affected parts to specifications and

install cotter pin to carrier bracket front bolt.

8. Insert a plastic plug from the inside of the floor

well to prevent dust and water entry.

Fig.
93—Removing Companion Flange

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-39

Fig.
103—Removing Bearing Caps

these joints are disassembled, repack bearings

and lubricate reservoir at end of trunnions with

high-melting point wheel bearing lubricant and

replace the dust seals.

1.
Remove bearing lock rings from trunnion yoke.

2.
Support trunnion yoke on a piece of 1-1/4" I.D. pipe

on an arbor bed.

NOTE:
Due to length of the propeller shaft it

may be more convenient to use a bench vise,

for removal and installation, instead of an arbor

press.
In this case, proceed with disassembly

and assembly procedure as with an arbor press.

3.
Using a suitable socket or rod, press trunnion down

far enough to drive bearing cup from yoke (fig. 103).

4.
Remove dust seals from trunnion, clean and inspect

bearing rollers and trunnion. Relubricate bearings

with a lithium base chassis lubricant.

NOTE:
In addition to packing the bearings,

make sure that the lubricant reservoir at the

end of each trunnion is completely filled with

lubricant. In filling these reservoirs, pack lu-

bricant into the hole so as to fill from the

bottom. This will prevent air pockets and ensure

an adequate supply of lubricant.

5. Place new dust seals on trunnions - cavity of seal

toward end of trunnion - then position Tool J-21548
over end of trunnion and into cavity portion of seal.

Press seal onto trunnion until tool bottoms against

trunnion (fig. 104). .

NOTE:
Installation of seal is critical to proper

sealing - use specified tool during installation to

prevent seal distortion and to assure proper

seating of seal on trunnion.

6. Partially install one bearing cup into yoke. Place

trunnion in yoke and into bearing cup. Install other

bearing cup and press both bearing cups into yoke

(fig. 105) being careful to keep trunnion aligned in

bearing cups.

7. Press bearing cups far enough to install lock rings,

and install lock rings.

Installation

1.
Inspect yoke seal in the transmission and replace, if

necessary, as described in the transmission section.

2.
Insert propeller shaft front yoke into transmission.

NOTE:
On Corvette models, install front yoke

into transmission then position propeller shaft

between yoke and companion flange; install "U"

bolts to front yoke.

3.
Align propeller shaft with companion flange, using

reference marks established in "Removal" pro-

cedure, connect the rear universal joint by installing

"U"
bolt clamps over bearing trunnions - torque

nuts to specifications.

Fig.
104—"U" Joint Trunnion Seal installation
Fig.
105—Installing Bearing Cup and Trunnion

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES
5-3

PRIMARY

SHOE

PAWL
WIRE LINK

OVERRIDE

LEVER

VERRIDE

SPRING

RETURN

SPRING

STAR
WHEEL

Fig.
3—Camaro
Pressure
Regulator
Valve
Fig.
4-Self-Adjusting
Brake

MAINTENANCE AND ADJUSTMENTS

In any service operation it is extremely important

that absolute cleanliness be observed. Any foreign matter

in the hydraulic system will tend to clog the lines, ruin

the rubber cups of the main and wheel cylinders and

cause inefficient operation or even failure of the braking

system. Dirt or grease on a brake lining may cause

that brake to grab first on brake application and fade

out on heavy brake application.

The split system consists basically of two separate

brake systems. When a failure is encountered on either,

the other is adequate to stop the vehicle. If one system

is not functioning, it is normal for the brake pedal lash

and pedal effort to substantially increase. This occurs

because of the design of the master cylinder which

incorporates ah actuating piston for each system. When

the rear system loses fluid and takes in air, its piston

will bottom against the front piston. When the front

system loses fluid and takes in air, its piston will

bottom on the end of the main cylinders body. The loss

of fluid in one of the systems causes an uneven hydraulic

pressure balance between the front and rear systems.

The brake pipe distribution and switch assembly, near

the main cylinder, detects the loss of pressure and il-

luminates the brake alarm indicator light on the instru-

ment panel. The pressure loss is felt at the brake pedal

by an apparent lack of brakes for most of the brake

travel and then, when failed chamber is bottomed, the

pedal will harden.

HYDRAULIC BRAKE FLUID

Use GM Hydraulic Brake Fluid, Supreme No. 11 or

equivalent when servicing brakes. This brake fluid is

satisfactory for any climate and has all the qualities

necessary for proper operation, such as a high boiling

point to prevent vapor lock and the ability to remain

fluid at low temperatures.
In the event that improper fluid has entered the system,

it will be necessary to service the system as follows:

1.
Drain the entire system.

2.
Thoroughly flush the system with clean alcohol,

188
proof,
or a hydraulic system cleaning fluid

such as "Declene".

3.
Replace all rubber parts of the system, including

brake hoses.

4.
Refill the system.

5. Bleed the system.

BLEEDING HYDRAULIC SYSTEM

The hydraulic brake system must be bled whenever

any line has been disconnected or air has in some way

entered the system. A ''spongy" pedal feeling when the

brakes are applied may indicate presence of air in the

system. The system must be absolutely free of air at

all times. Bleeding should be done on the longest line

first; the proper sequence to follow is left rear, right

rear, right front, and left front (fig. 5). Bleeding of

brake system may be performed by one of two methods—

either pressure or manual.

PRESSURE
BLEEDING

1.
Clean all dirt from top of main cylinder and remove

cylinder cover and rubber diaphragm.

2.
Reduce fluid level in main cylinder until reservoirs

are approximately half full.

NOTE:
Make sure brake fluid in bleeder equip-

ment is at operating level and that the. equipment

is capable of exerting 30 to 50 lbs. hydraulic

pressure on the brake system.

3.
Install brake bleeder adapter J-22489 (fig. 6) on

main cylinder. Connect hose from bleeder equipment

to bleeder adapter and open release valve on bleeder

equipment.

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-4

RF

3

^ FRONT OF

~ VEHICLE

LF

4
RR

CZZZIZ3

2

LR

1

Fig.
5—Correct Bleeding Sequence

4.
Install brake bleeder wrench, Tool J-21472 on bleed-

er valve at wheel cylinder and install one end of

bleeder hose on bleeder valve (fig. 7).

5.
Pour a sufficient amount of brake fluid into a trans-

parent container to insure that end of bleeder hose

will remain submerged during bleeding. Place the

loose end of bleeder hose into the container. Be

sure the hose end is submerged in the fluid.

6. Open wheel cylinder bleeder valve by turning Tool

J-21472 counterclockwise approximately 1/3 of a

turn and observe flow of fluid at end of bleeder

hose.

7.
Close bleeder valve tightly as soon as bubbles stop

and brake fluid flows in a solid stream from the

bleeder hose.

8. Remove brake bleeder wrench and bleeder hose

from wheel cylinder bleeder valve.

9. Repeat Steps 4 through 8 on the remaining wheel

Cylinders in the correct bleeding sequence (fig. 5).

10.
Disconnect bleeder equipment from brake bleeder

adapter cover J-22489.

NOJE: The main cylinder on certain passenger

car models is tilted upward. When removing

the bleeder adapter on these models, place a

clean dry cloth behind and below the cylinder

to absorb any fluid spillage as the cover is

removed. v
Fig.
7—Bleeding Brakes Using Brake Bleeder

Wrench Tool J-21472

11.
adapter J-22489. Wipe all area

fluid was spilled during adapter

Fig.
6—Brake Bleeder Adapter Tool J-22489—Installed
Remove bleeder

dry of fluid if

removal.

12.
Fill master cylinder reservoirs to within 1/4" of

reservoir rims as shown in Figure 8.

13.
Install main cylinder diaphragm and cover.

MANUAL BLEEDING

1.
Clean all dirt from top of main cylinder and remove

cylinder cover and rubber diaphragm.

2.
Fill main cylinder reservoirs.

3.
Install brake bleeder wrench, Tool J-21472 on bleed-

er valve at wheel cylinder and install one end of

bleeder hose on bleeder valve (fig. 7).

4.
Pour a sufficient amount of brake fluid into a trans-

parent container to insure that end of bleeder hose

will remain submerged during bleeding. Place the

loose end of bleeder hose into the container. Be

sure the hose end is submerged in the fluid.

NOTE: Carefully monitor fluid level at main

cylinder during manual bleeding operations. Do

not bleed enough fluid at one time to drain the

reservoir completely. Replenish the reservoirs

with fluid while bleeding to insure a sufficient

amount of fluid is in the main cylinder at all

times.
To insure that outside air is not sucked

back into the hydraulic system, the bleeder

valve should be closed before the brake pedal

reaches the floor.

5.
Open wheel cylinder bleeder valve by turning Tool

J-21472 counterclockwise approximately 1/3 of a

turn. Slowly depress brake pedal. Just before brake

pedal reaches the end of its travel, close bleeder

valve and allow brake pedal to return slowly to the

fully released position. Repeat this procedure until

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-5

LEVEL CYLINDER

TILTED CYLINDER

Fig.
8—Correct Main Cylinder Fluid Level

expelled brake fluid flows in a solid stream from the

bleeder hose and no bubbles are present, then close

bleeder valve tightly.

6. Remove brake bleeder wrench and bleeder hose from

wheel cylinder bleeder valve.

7. Repeat Steps 2 through 7 on the remaining wheel

cylinders in the correct bleeding sequence (fig. 5).

8. Fill the main cylinder to the levels shown in

Figure 8.

9. Install main cylinder diaphragm and cover.

PUSH ROD TO MAIN CYLINDER CLEARANCE

The brake pedal has a definite stop which is permanent

and not adjustable. This stop consists of a rubber

bumper at the release end of pedal travel. Before

adjusting push rod to main cylinder clearance, make

sure pedal returns to the fully released position freely

and that the pedal retracting spring has hot lost its

tension, then proceed as follows:

1.
Loosen check nut on push rod.

2.
Turn push rod as required to provide correct ad-

justment. Movement of pedal pad before push rod

contacts main cylinder pistons must be 1/16" to

1/4" (fig. 9).

3.
Tighten check nut against clevis, and recheck

movement.

HYDRAULIC BRAKE LINES

Hydraulic Brake Hose

The flexible hoses which carry the hydraulic pressure

from the steel lines to the wheel cylinders are carefully

designed and constructed to withstand all conditions of

stress and twist which they encounter during normal

vehicle usage.
The hoses require no service other than periodic

inspection for damage from road hazards or other like

sources. Should damage occur and replacement become

necessary, the following procedure is to be followed.

Removal

1.
Separate hose from steel line by turning double

flare connector out of hose fitting.

2.
Remove "U" shaped retainer from hose fitting and

withdraw hose from support bracket.

3.
Turn hose fitting out of wheel cylinder inlet.

Replacement

1.
Install new copper gasket on cylinder end of hose

(male end).

2.
Moisten threads with brake fluid and install hose in

wheel cylinder inlet.

3.
With weight of car on wheels and suspension in

normal position (front wheels straight ahead) pass

female end of hose through support bracket, allowing

hose to seek its own position. Insert hex of hose

fitting into the 12 point hole in support bracket

in position which induces least twist to hose (figk 10).

NOTE:
Do not twist hose unduly during ^

operation as its natural curvature is absolutely

necessary to maintain proper hose-tot

suspension clearance through full movement o£

the suspension and steering parts.

4.
Install "U" shaped retainer to secure hose in sup-

port bracket.

5. Inspect by removing weight completely from wheel,

turn wheels from lock to lock while observing hose

position. Be sure that hose does not tough other

parts at any time during suspension or wheel travel.

If contact does occur, remove hose retainer and

rotate the female hose end in the support bracket

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-6

Fig.
9—Brake Pedal Free Movement

one or two points in appropriate direction, replace

retainer, and re-inspect.

6. Place steel tube connector in hose fitting and tighten

securely.

7. Bleed all brakes as outlined in this section.

8. Do not tighten male end (wheel cylinder end) once

the other end is fixed. If necessary to tighten male

1 end, disconnect hose at opposite end, then reconnect

following above procedure.

Hydraulic Brake Tubing

Hydraulic brake tubing is a double layer annealed

steel terne plate tubing which resists corrosion and has

the physical strength to stand up under the high pr.es-
Fig.
11—Hydraulic Brake Tube Double Flaring Tool

sures which are developed when applying the brakes. In

making up hydraulic brake pipes, it is important that

the proper flaring tool be used to flare the ends of the

tubing for the compression couplings. Unless the tubing

is properly flared, the connections will leak and the

brakes will become ineffective.

CAUTION: When necessary to replace brake

tubing, always use special steel tubing which

is designed to withstand high pressure and re-

sist corrosion. Ordinary copper tubing is not

satisfactory and should not be used.

This safety steel tubing must be double-lap flared at

the ends in order to produce a strong leak-proof joint.

The brake tube flaring. Tool J-8051 (fig. 11) is used to

form the double-lap flare.

Figure 12 shows two pieces of tubing, one with single-

lap flare "A" and the other with double-lap flare "B".

It will be noted that the single-lap flare in "A" split

the tubing while the one shown in "B" is well-formed and

unbroken due to the reinforcement of the double wall.

The following procedure should be followed in making

up hydraulic brake pipes.

Double Lap Flaring

1.
Clamp the tubing in the proper size die blocks with

the flat ends of the blocks toward the end of the

tubing to be cut off. Cut the end of the tubing flush

and square. Using a mill file, dress tubing and

square ends.

Fig.
10-Brake Line Support Bracket

Fig.
12—Single and Double Lap Flaring

CHEVROLET CHASSIS SERVICE MANUAL