Page 17 of 478
Vehicle Information, Consumer Information and Reporting Safety Defects2-10
Items Weight of volume Classification
Refrigerant o
z. (g)15.87 (450) ± 0.88 (25) R-1234yf
Compressor lubricant oz. (g)4.23 (120) ± 0.35 (10) PAG
Contact an authorized HYUNDAI dealer for more details.
VOLUME AND WEIGHT
Items 2.0 T-GDI
2WD DCT
Gross vehicle weight
lbs. (k
g) 4,431 (2010)
Luggage volume (VDA) F X I W b MIN : 12.75 (361)
MAX : 40.36 (1,143)
DCT : Dual clutch transmission
MIN : Behind rear seat to upper edge of the seat back.
MAX : Behind front seat to roof.
AIR CONDITIONING SYSTEM
Page 18 of 478

02
2-11
RECOMMENDED LUBRICANTS AND CAPACITIES
To help achieve proper engine and powertrain performance and durability, use only
lubricants of the proper quality. The correct lubricants also help promote engine
efficiency that results in improved fuel economy.
These lubricants and fluids are recommended for use in your vehicle.
LubricantVolumeClassification
Engine oil
*1 *2 *3
(drain and refill)
Recommends
5.49 US qt. b SAE 0W-30 API SN PLUS/SP or
ILSAC GF-6 *4
Dual clutch
transmission fluid Gear oil
3.4 US qt.
b GS WDCTF HD G (GS CALTEX)
Control oil 2.58 US qt.
b GS WDCTF HD H (GS CALTEX)
Coolant 7.3 US qt.
b Mixture of antifreeze and distilled
water (Ethylene-glycol with
phosphate based coolant for
aluminum radiator)
Brake fluid 0.74 ~ 0.85 US qt
a b DOT4
Fuel 13.21 US gal.
(50 b) Refer to “Fuel Requirements” in the
Introduction chapter.
*1 : Refer to the recommended SAE viscosity numbers on the next page.
*2 : For the best performance of braking and ABS/ESC functions, you should use genuine
brake fluid that conform to standards. (Standards: SAE J1704 DOT-4 LV, ISO4925 CLASS-6
and FMVSS116 DOT-4)
*3 : An engine oil displaying this American Petroleum Institute(API) Certification
Mark conforms to the International Lubricant Specification Advisory
Committee (ILSAC). It is recommended to only use engine oils that uphold
this API Certification Mark.
*4 : Requires < API SN PLUS (or above) Full synthetic> grade engine oil. If a lower grade
engine oil (mineral oil including Semi-synthetic) is used, then the engine oil and engine
oil filter must be replaced as indicated severe maintenance condition.
Page 19 of 478

Vehicle Information, Consumer Information and Reporting Safety Defects2-12
Recommended SAE Viscosity Number
CAUTION
Always be sure to clean the area around any filler plug, drain plug, or dipstick before
checking or draining any lubricant. This is especially important in dusty or sandy
areas and when the vehicle is used on unpaved roads. Cleaning the plug and dipstick
areas will prevent dirt and grit from entering the engine and other mechanisms that
could be damaged.
Engine oil viscosity (thickness) has an effect on fuel economy and cold weather
operating (engine start and engine oil flowability). Lower viscosity engine oils can
provide better fuel economy and cold weather performance, however, higher viscosity
engine oils are required for satisfactory lubrication in hot weather. Using oils of any
viscosity other than those recommended could result in engine damage.
When choosing an oil, consider the range of temperature your vehicle will be operated
in before the next oil change. Proceed to select the recommended oil viscosity from
the chart.
Temperature Range for SAE Viscosity Numbers
Temperature °C -30 -20 -10 0 10 20 30 40 50
(°F) -10 0 20 40 60 80 100 120
Engine Oil
0W-30
Page 20 of 478