2022 LEXUS NX300h Owners Manual

Installingchildrestraintsystemusingaseatbelt(childrestraintlockfunction
belt)
A child restraint system for a small child or baby must itself be properly restrained
on the seat with the lap portion of the lap/shoulder belt.
Install the child restraint system in accordance to the operation manual enclosed with the child restraint system.
If the child restraint system on hand is not within the kuniversaly category (or the
necessary information is not in the table), refer to the kVehicle Listy provided by the
child restraint system maker for various possible installation positions, or check the
compatibility after asking the retailer of the child seat.
Rear-facing-Infantseat/convertible
1Adjust the rear seat
If there is a gap between the child seat and the seatback, adjust the seatback until good
contact is achieved.
2 Place the child restraint system on the rear
seat facing the rear of the vehicle.
3 Run the seat belt through the child restraint
system and insert the plate into the buckle.
Make sure that the belt is not twisted.
4 Fully extend the shoulder belt and allow it to
retract to put it in lock mode. In lock mode,
the belt cannot be extended.
1-4.Preparationsforsafedrivingwithchildreninthevehicle631
Before driving

5While pushing the child restraint system
down into the rear seat, allow the shoulder
belt to retract until the child restraint system is
securely in place.
After the shoulder belt has retracted to a point
where there is no slack in the belt, pull the belt to
check that it cannot be extended.
6 After installing the child restraint system, rock it back and forth to ensure that it
is installed securely.
Forward-facing-Convertible
1 Adjust the seat

5Fully extend the shoulder belt and allow it to
retract to put it in lock mode. In lock mode,
the belt cannot be extended.
6 While pushing the child restraint system into
the rear seat, allow the shoulder belt to re-
tract until the child restraint system is securely
in place.
After the shoulder belt has retracted to a point
where there is no slack in the belt, pull the belt to
check that it cannot be extended.
7 If the child restraint has a top tether strap, follow the child restraint manufactur-
er
s operation manual regarding the installation, using the top tether strap to latch onto the top tether strap anchor.
8 After installing the child restraint system, rock it back and forth to ensure that it
is installed securely.
Boosterseat
1 If installing the child restraint system to the front passenger seat is unavoidable,
refer to
: P.67 .
2 High back type: If the head restraint interferes with your child restraint system,
and the head restraint can be removed, remove the head restraint. Otherwise,put the head restraint in the upper most position.
3 Place the child restraint system on the seat facing the front of the vehicle.
Boostertype
1-4.Preparationsforsafedrivingwithchildreninthevehicle651
Before driving

Highbacktype
4Sit the child in the child restraint system. Fit
the seat belt to the child restraint system according to the manufacturer
s instructions
and insert the plate into the buckle. Make
sure that the belt is not twisted.
Check that the shoulder belt is correctly posi-
tioned over the child
s shoulder and that the lap
belt is as low as possible.
WARNING

Installingachildrestraintsystemtothefrontpassengerjsseat
Do not install a child restraint system to the front passengerjs seat unless it is unavoidable. In the event of an accident, the force of deployment of an SRS airbag
can cause death or serious injury to a child.
If installation of a child restraint system to the front passengerjs seat is unavoidable,
adjust the front passengerjs seat as follows:

Entering/exitingthevehicleandloadingluggage
Keytypes
The following keys are provided with the vehicle. A
Electronic keys

NOTICEremove the battery cover, lightly grasp and pull it.) If the battery is corroded, have your
Lexus dealer replace the battery.