2019 MERCEDES-BENZ CLA Owners Manual

XTo switch off the high-beam headlamps:move the combination switch back to its nor-mal position.The blueWindicator lamp in the instru-ment cluster goes out.
Vehicles with Adaptive Highbeam Assist:when Adaptive Highbeam Assist is active, itcontrols activation and deactivation of thehigh-beam headlamps (Ypage 103).
XTo switch on the high-beam flasher:pullthe combination switch in the direction ofarrow

Switching Adaptive Highbeam Assist
on/off
XTo switch on:turn the light switch toX.
XPress the combination switch beyond thepressure point in the direction of arrowC.The

Interior lighting control
General notes
In order to prevent the vehicle's battery fromdischarging, the interior lighting functions areautomatically deactivated after some timeexcept when the SmartKey is in positionHinthe ignition lock.
The color and brightness of the ambient lightingare set via the multimedia system (see DigitalOperator's Manual).
Automatic interior lighting control
XTo switch on:set the switch to center posi-tion

Vehicles with halogen headlamps
CTurn signal lamp: PY 21 W
DHigh-beam headlamps/daytime runninglamps/parking lamps/standing lamps:H15 55 W/15 W

XInsert the new bulb into bulb holderD.
XInsert bulb holderDand turn it clockwise.
XPress on housing coverCand turn it to theright.
XReplace the cover in the front wheel housing(Ypage 106).
High-beam headlamps/daytime run-
ning lamps/parking lamps and stand-
ing lamps (halogen headlamps)
XSwitch off the lights.
XOpen the hood.
XTurn housing coverCcounter-clockwise andremove it.
XTurn bulb holderDcounter-clockwise andpull out.
XInsert the new bulb and engage it to the stop.
XPress on housing coverCand turn it to theright.
Turn signals (halogen headlamps)
XSwitch off the lights.
XOpen the hood.
XTurn bulb holderCcounter-clockwise andpull out.
XTurn the bulb counter-clockwise and pull itout of bulb holderC.
XInsert the new bulb into bulb holderC.
XInsert bulb holderCand turn it clockwiseuntil it engages.
Replacing rear bulbs
Opening and closing the side trim pan-
els
View of right-hand side trim panel
You must open the side trim panel in the trunkbefore you can replace the bulbs in the taillamps.
XTo open:release right or left side trimpanelCat the top and fold it down in thedirection of the arrow.
XTo close:insert side panelC.
Tail lamps
XSwitch off the lights.
XOpen the trunk.
XOpen the side trim panel (Ypage 107).
Replacing bulbs107
Lights and windshield wipers
Z

XPress retaining clipsCat the same time inthe direction of the arrows.
XCarefully remove the bulb holder togetherwith the connected plug and the bulbs.
Bulb holder
DBrake lamp

Replacing the wiper blades
Important safety notes
GWARNING
If the windshield wipers begin to move while
you are changing the wiper blades, you could
be trapped by the wiper arm. There is a risk of
injury.
Always switch off the windshield wipers and
ignition before changing the wiper blades.
!To avoid damaging the wiper blades, makesure that you touch only the wiper arm of thewiper.
!Never open the hood if a windshield wiperarm has been folded away from the wind-shield.
Never fold a windshield wiper arm without awiper blade back onto the windshield.
Hold the windshield wiper arm firmly whenyou change the wiper blade. If you release thewindshield wiper arm without a wiper bladeand it falls onto the windshield, the windshieldmay be damaged by the force of the impact.
Mercedes-Benz recommends that you havethe wiper blades changed at a qualified spe-cialist workshop.
Changing the windshield wiper blades
Removing the wiper blades
XVehicles without KEYLESS-GO or KEY-LESS-GO start function:remove the Smart-Key from the ignition lock.
XVehicles with KEYLESS-GO or KEYLESS-GO start function:switch off the engine.
XFold the wiper arm away from the windshield.
XHold on to the wiper arm with one hand. Withthe other hand, turn wiper blade in directionof arrowCaway from the wiper arm as far asit will go.
XSlide catchDin the direction of arrow

XSlide catchDin the direction of arrow