2018 HYUNDAI I20 Owners Manual

1.$$
,204/3424-3
HHeadlight, Parking (Position)
Light, Turn signal Light, Low
Beam Assist-Static Light, Fog
Light and Daytime Running Light
bulb replacement(1) Headlight (Low/High) *
1
(2) Parking (Position) Light
(3) Front Turn signal Light
(4) Daytime Running Light
(if equipped)
(5) Front Fog Light (if equipped)
*1: MFR (Multi Focus Reflector) Headlight (1) Headlight (Low/High) *
2
(2) Low Beam Assist-Static Light
(3) Front Turn Signal Light
(4) Position Light/ Daytime Running Light (DRL)
(5) Front Fog Light (if equipped)
*2: Bi-Function Projection Headlight (1) Headlight (Low/High) *
1
(2) Parking (Position) Light
(3) Front Turn signal Light
(4) Front Fog Light (if equipped)
*1: MFR (Multi Focus Reflector)
Headlight
OIB077068
■ 5 Door
• Type A
OIB077069
■5 Door
• Type B
OIB077070
■Cross
• Type A

1.$',204/3424-3
(1) Headlight (Low/High) *
2
(2) Low Beam Assist-Static Light
(3) Front Turn Signal Light
(4) Position Light/ Daytime Running Light (DRL)
(5) Front Fog Light (if equipped)
*2: Bi-Function Projection Headlight
II nformation
If the headlight aiming adjustment
is necessary after the headlight
assembly is reinstalled, consult an
authorized HYUNDAI dealer.
The Fog Light aiming adjustment can be done by removing UNDER
COVER. Consult an authorised
HYUNDAI dealer.i(Continued)•
Always handle them carefully,
and avoid scratches and abra-
sions. If the bulbs are lit, avoid
contact w ith liquids. Never touch
the glass with bare hands.
Residual oil may cause the bulb
to overheat and burs t when lit. A
bulb should be operated only
when installed in a headlight.
•
If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
•
Wear eye protection when
changing a bulb. Allow the bulb
to cool down before handling it.
Halogen bulbs•
Halogen bulbs contain pressur-
ized gas that will produce flying
pieces of glass if broken.
(Continued)
WARNING
OLMB073042L
OIB077060
■Cross
• Type B

1.$1
,204/3424-3
HHeadlight (Low/High)1. Open the hood.
2. Remove the headlight bulb cover
by turning it counterclockwise.
3. Disconnect the headlight bulb socket-connector. 4. Unsnap the headlight bulb retain-
ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head- light assembly.
6. Install a new headlight bulb and snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Information
- Bi-Function projection
headlight
This headlight is bi-function type that
switches the low beam to high or the
high beam to low using solenoid sys-
tem. So, the moving sound may be
heard when the headlight switches the
low beam to high or the high beam to
low and it does not indicate malfunc-
tion of the headlight.
Turn signal light1. Remove the turn signal light bulb cover by turning it counterclock-
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
i
OIB074048
Turn signal light
Parking
(Position) light
Headlight
■ MFR (Multi Focus Reflector) Headlight
OIB075061
Turn signal light
Headlight
■Bi-Function Projection Headlight

1.',204/3424-3LLow Beam Assist-Static Light1. Open the hood.
2. Remove the Low Beam Assist-
Static Light bulb cover by turning it
counterclockwise.
3. Disconnect the Low Beam Assist- Static Light bulb socket-connector.
4. Unsnap the Low Beam Assist- Static Light bulb retaining wire by
depressing the end and pushing it
upward.
5. Remove the bulb from the Low Beam Assist-Static Light assem-
bly. 6. Install a new Low Beam Assist-
Static Light bulb and snap the Low
Beam Assist-Static Light bulb
retaining wire into position by
aligning the wire with the groove
on the bulb.
7. Connect the Low Beam Assist- Static Light bulb socket connector.
8. Install the Low Beam Assist-Static Light bulb cover by turning it clock-
wise.
Parking (Position) light1. Remove the socket from theassembly by pulling it straight out.
2. Remove the bulb from the socket by pulling it out.
3. Insert a new bulb by inserting it into the socket.
4. Install the socket in the assembly by pushing it in.
Front fog light or Daytime runninglight (if equipped)
OIB075061
Low Beam Assist-Static Light
OIB077071OIB077072OIB077073
■
5 Door
• Type A (without DRL)■5 Door
• Type A (with DRL)■ Cross

1.'&
,204/3424-3
1. Remove the under cover by rotat-ing the screws and bolts.
2. Reach your hand into the back of the front bumper.
3. Disconnect the power connector from the socket.
4. Remove the bulb-socket from the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the housing.
5. Install the new bulb-socket into the housing by aligning the tabs on
the socket with the slots in the
housing. Push the socket into the
housing and turn the socket clock-
wise.
6. Connect the power connector to the socket.
7. Reinstall the front bumper under cover.
PPosition light/Daytime running light(if equipped)Your vehicle is equipped with LED
lamps. LED lamps do not have
replaceable bulbs. If the LED lamp
does not operate, we recommend
that the vehicle be checked by an
authorized HYUNDAI dealer.
Side repeater light (LED)
replacement (if equipped)If the light does not operte, we rec-
ommend that the vehicle be checked
by an authorized HYUNDAI dealer.
OIB074035

1.'),204/3424-3
1. Using a flat-blade screwdriver, remo ve the light assembly from
the body of the vehicle by prying
the housing and pulling the
assembly out.
2. Separate the socket and the lens part by turning the socket counter-
clockwise until the tabs on the
socket align with the slots on the
lens part.
3. Remove the bulb by pulling it straight out.
4. Insert a new bulb in the socket.
5. Reassemble the socket and the housing part.
6. Reinstall the light assembly to the body of the vehicle.
IInterior light bulb replacement1. Using a flat-blade screwdriver,
gently pry the lens from the interi-
or light housing. 2. Remove the bulb by pulling it
straight out.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interior light housing notches and snap
the lens into place.
Be careful not to dirty or damage
lens, lens tab, and plastic housings. NOTICE
■ Room lamp■Luggage room lamp
OIB074042OIB074041
OIB074040
■Cross

1.'(
,204/3424-3
$  "$# $Exterior careExterior general caution It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning
and caution statements that appear
on the label. High-pressure washing• When using high-pressure washers,
make sure to maintain sufficient dis-
tance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.
• Do not spray the camera, sensors or its surrounding area directly with a
high pressure washer. Shock appliedfrom high pressure water may cause
the device to not operate normally.• Do not bring the nozzle tip close to boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
Finish maintenanceWashing To help protect your vehicle’s finish
from rust and deterioration, wash it
thoroughly and frequently at least
once a month with lukewarm or cold
water.
If you use your vehicle for off-road
driving, you should wash it after each
off-road trip. Pay special attention to
the removal of any accumulation of
salt, dirt, mud, and other foreign
materials. Make sure the drain holes
in the lower edges of the doors and
rocker panels are kept clear and
clean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar
deposits can damage your vehicle’s
finish if not removed immediately.
Even prompt washing with plain
water may not completely remove all
these deposits. A mild soap, safe for
use on painted surfaces, may be
used.
After washing, rinse the vehicle thor-
oughly with lukewarm or cold water.
Do not allow soap to dry on the fin-
ish.
• Do not use strong soap, chemicaldetergents or hot water, and do not
wash the vehicle in direct sunlig ht
or when the body of the vehicle is
warm.
• Be careful when washing the side windows of your vehicle.
Especially, with high-pressure
water, water may leak through the
windows and wet the interior.
• To prevent dam age to the plastic
parts and lamps, do not clean with
chemical solvents or strong deter- gents. NOTICEWet brakes
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by
water. If braking performance is
impaired, dry the brakes by apply-
ing them lightly while maint aining
a slow forward speed.
WARNING

1.'#,204/3424-3
•• Water washing in the engine com-
partment including high pressure
water washing may cause the fail-
ure of electrical circuits located in
the engine compartment.
• Never allow water or other liquids to come in contact with
electrical/electronic components
inside the vehicle as this may dam-
age them.
WaxingWax the vehicle when water will no
longer bead on the paint.
Always wash and dry the vehicle
before waxing. Use a good quality
liquid or paste wax, and follow the
manufacturer’s instructions. Wax all
metal trim to protect it and to main-
tain its luster.
Removing oil, tar, and similar materi-
als with a spot remover will usually
strip the wax from the finish. Be sure to
re-wax these areas even if the rest of
the vehicle does not yet need waxing. • Wiping dust or dirt off the body with a dry cloth will scratch the finish.
• Do not use steel wool, abrasive cleaners , or strong detergents con-
taining highly alkaline or caustic
agents on chrome-plated or
a nodized aluminum parts. This
may result in damage to the pro-
tective coating and cause discol-
oration or paint deterioration.
Finish damage repair Deep scratches or stone chips in the
painted surface must be repaired
promptly. Exposed metal will quickly
rust and may develop into a major
repair expense.
Information
If your vehicle is damaged and
requires any metal repair or replace-
ment, be sure the body shop applies
anti-corrosion materials to the parts
repaired or replaced. i
NOTICE
NOTICE
OLMB073082