2018 FIAT 500 battery

READ THIS CAREFULLY
REFUELLING
Petrol engines: Only refuel with unleaded petrol with octane rating (RON) not less than 95, in compliance with the European
specification EN228. Do not use petrol containing methanol or ethanol E85. Using these mixtures may cause misfiring and driving
issues, as well as damage fundamental components of the supply system.
Diesel engines: refuel only with Diesel fuel motor vehicles conforming to the European specification EN590. The use of other
products or mixtures may damage the engine beyond repair and consequently invalidate the warranty, due to the damage caused.
For further details on the use of the correct fuel see the “Refuelling the vehicle” paragraph in the “Starting and driving” chapter.
STARTING THE ENGINE
Versions with manual gearbox (petrol engines): make sure that the handbrake is engaged, put the gear in neutral, fully
depress the clutch without pressing the accelerator, then turn the ignition key to AVV and release it as soon as the engine has
started.
Versions with manual gearbox (diesel engines): make sure that the handbrake is engaged, put the gear in neutral, fully
depress the clutch pedal without pressing the accelerator, then turn the ignition key to MAR and wait for the
mwarning
lights to switch off. Turn the ignition key to AVV and finally release it as soon as the engine starts.
Versions with automatic transmission: make sure that the handbrake is engaged and that the gear lever is in P (Parking) or N
(Neutral), fully depress the brake pedal, then turn the ignition key to AVV.
PARKING ON FLAMMABLE MATERIAL
The catalytic converter develops high temperatures during operation. Do not park the car on grass, dry leaves, pine needles or
other flammable material: fire hazard.
RESPECTING THE ENVIRONMENT
The vehicle is fitted with a system that carries out a continuous diagnosis of the emission-related components in order to help
protect the environment.
ELECTRICAL ACCESSORIES
If, after buying the vehicle, you decide to add electrical accessories (with the risk of gradually draining the battery), contact a Fiat
Dealership. They can calculate the overall electrical requirement and check that the electric system of the vehicle can support the
required load.
SCHEDULED SERVICING
Correct maintenance of the car is essential for ensuring that it maintains its performance and its safety features, its environmental
friendliness and low running costs for a long time to come.
K



KNOWING YOUR CAR
12
HOT ENGINE COOLANT
The warning light switches on when the ignition key is turned to MAR, but it should switch off after a few seconds.
The warning light or symbol on the display lights up when the engine is overheated, on some versions, together with a
dedicated message on the display.
❒ In normal driving conditions: stop the car, switch off the engine and check that the fluid level in the reservoir is not
below the MIN mark. In this case, wait for the engine to cool down, then slowly and carefully open the cap, top up with
coolant and check that the level is between the MIN and MAX marks on the reservoir itself. Also check visually for any
fluid leaks. Should the warning light turn on again at the next start-up, contact a Fiat Dealership.
❒ if the vehicle is used under demanding conditions (e.g. towing trailers uphill or fully loaded): slow down and, if the
light stays on, stop the car. Stop for two or three minutes with the engine running and slightly accelerated to facilitate
better coolant circulation, then turn the engine off. Check that the coolant level is correct as described above.
IMPORTANT Over demanding routes, it is advisable to keep the engine running and slightly accelerated for a few minutes
before turning it off.
On certain versions the dedicated message is displayed.uu
{{
“DUALDRIVE” ELECTRIC POWER STEERING FAULT
When the key is turned to MAR, the warning light switches on but it should switch off after a few seconds.
If the warning light stays on, on some versions along with a dedicated message on the display, you may not have steering
assistance and the effort required to operate the steering wheel could be notably increased; steering is, however, possible.
In this case, contact a Fiat Dealership.
If the warning light switches on while driving (on some versions, together with a dedicated message on the display) you may
not have steering assistance. Although it will still be possible to steer the vehicle, the effort needed to operate the steering
wheel could be increased: contact a Fiat Dealership as soon as possible.
IMPORTANT In some circumstances, factors independent of the electric power steering could cause the warning light on
the instrument panel to switch on. In this case, stop the car immediately (should it be in motion), stop the engine for about
20 seconds and then restart the engine. If the warning light stays on, contact a Fiat Dealership.
IMPORTANT After the battery is disconnected, the steering must be initialised. The warning light switches on to indicate
this. To carry out this procedure, simply turn the steering wheel all the way from one end to the other or drive in a straight
line for about a hundred metres.

13
INSUFFICIENT ENGINE OIL PRESSURE/DECAYED ENGINE OIL
When the ignition key is turned to MAR, the warning light (for versions/markets, where provided) switches on, but it should
switch off as soon as the engine is started.
NOTE For versions/markets, where provided, the indicator may be amber.
Low engine oil pressure
The warning light or the symbol switches on constantly along with a message on the display (for versions/markets, where
provided) when the system detects that engine oil pressure is low.
Engine oil degraded
The warning light switches on and a message is displayed (for versions/markets, where provided).
The warning light may flash in the following ways, depending on the version:
❑ cycles of 3 minutes with intervals with the warning light off for 5 seconds until the oil is changed.
After the initial warning, each time the engine is started up, the warning light will continue to flash in the same mode, until
the oil is changed. A specific message will appear on the display (for versions/
markets, where provided) in addition to the warning light. The lighting of this warning light should not be considered as a
fault, it simply informs the customer that the oil needs to be changed following normal car use.
Engine oil deterioration is accelerated by:
❑ mainly town use of the car which makes the DPF regeneration process more frequent;
❑ use of the vehicle for short drives, in which the engine does not have time to reach its regular operating temperature;
❑ repeated interruption of the regeneration process, signalled by the DPF warning light coming on.
vv
vv
DOORS/BONNET/LUGGAGE COMPARTMENT OPEN (versions with multifunction display)
The warning light appears on the display, together with a dedicated message, on some versions, when one or more doors,
the tailgate or the bonnet (for versions/markets, where provided) are not properly closed.
An acoustic signal is also emitted with the doors open and the car in motion.
ww
LOW BATTERY CHARGE
The warning light switches on when the ignition key is turned to MAR, but it should switch off as soon as the engine has
started (with the engine idling a brief delay before switching off is acceptable).
If the warning light or the symbol on the display (together with a dedicated message on the display on some versions)
remains on, contact a Fiat Dealership immediately.

39
ROOF 10) 5)
FIXED GLASS ROOF
(for versions/markets, where provided)
The large glazed roof includes a
transparent panel provided with
manually operated blinds. The blinds
can be used in the “all closed” or “all
open” positions (there are no
fixed intermediate positions).
❒ To open the blind: grip the handle
and press the catch A-fig. 31, then
release the blind and bring it to the
“all open” position.
To close it, repeat the same
operation in the opposite direction.
SUNROOF
(for versions/markets, where provided)
To move the blinds, follow the
instructions in “fixed glass roof”
Opening the sunroof
❒ Keep the button A-fig. 32 pressed:
the sunroof will move to “spoiler”
position.
To fully open the sunroof press
button A again and hold it down: the
sunroof will stop in the position
reached when the button is
released.
32DVDF0S018c
Closing the sunroof
❒ Keep the button B-fig. 32 pressed:
the sunroof will move to “spoiler”
position.
The sunroof will stop in the position
reached when the button is
released. Press button B again and
hold it down until the sunroof is
completely closed.
Anti-pinch device
❒
The sunroof has an anti-pinch safety
system capable of detecting the
presence of an obstacle whilst the
sunroof is closing. When this
happens, the system stops and the
movement of the sunroof is
immediately reversed.
Initialisation procedure
The sunroof must be re-initialised after
disconnecting the battery or if the
relevant protection fuse is blown.
Proceed as follows:
❒ keep the button A fig. 32 pressed
so that the sunroof closes
completely in stages
❒ after full closing, wait for the sunroof
motor to stop.
31DVDF0S017c

KNOWING YOUR CAR
42
Emergency manoeuvre
If the switches fail, the soft top can be
moved manually proceeding as
described below:
❒ take the key provided and located in
the boot together with the tool box
or the Fix&Go kit;
❒ fit the wrench in the special housing
A-fig. 37 inside the luggage
compartment, under the parcel
shelf;
❒ turn in clockwise direction to open
the soft top and counter-clockwise
to close it.
37DVDF0S176c
Initialisation procedure
The soft top must be re-initialised after
disconnecting the battery or if the
relevant protection fuse is blown.
Proceed as follows:
❒ before carrying out any other
operation, make sure the engine is
on during the whole initialisation
procedure;
❒ keep the opening button A-fig. 34
pressed until the soft top is
completely open;
❒ when the soft top is completely
open, keep the button pressed for
at least 2 seconds;
❒ keep the closing button B-fig. 34
pressed until the soft top is
completely closed;
❒ when the soft top is completely
closed, keep the button B-fig. 34
pressed for at least 2 seconds.When the procedure is terminated, the
soft top will automatically carry out a
complete opening and closing cycle
(up to 25 cm from the completely
closed position) to inform the driver
that correct operation has been
restored.
Important notes
❒ The horizontal and vertical parts of
the soft top can be operated at any
speed lower than 100 and 80 km/h
respectively.
❒ The top can be operated at any
temperature in the range from
-18 to +80°C.
❒ It is recommended to have the
engine running always when
opening or closing the soft top.
❒ If required, remove the battery with
open or closed soft top, but NOT
when the soft top is moving.
❒ Do not fix a roof rack to the top and
do not travel with objects resting on
the open top.

45
BOOT 13)
ELECTRIC HANDLE
(SOFT TOUCH)
❒ Operate the electric handle A-fig. 41
to open the tailgate.
❒ To release the lock manually, use
the metal insert of the ignition key.
❒ To release the lock with the remote
control, press button R.
❒ To close, use the handle located
inside the tailgate.
❒ If the tailgate is not shut properly the
dedicated instrument panel or
colour display warning light (where
provided) will switch on.
41DVDF0S025c
Opening the tailgate with soft top
all open
❒ Pressing the tailgate opening
one-touch button A-fig. 41 to
automatically close the soft top to
spoiler position. The tailgate can be
opened in spoiler position.
Hatchback emergency opening
To open the tailgate from the
passenger compartment if the car
battery is run down or the electric
tailgate lock is faulty, proceed as
follows:
❒ remove the rear head restraints;
❒ fold the seat backrests over;
❒ press lever A-fig. 42 inside the
luggage compartment.
42DVDF0S026c
ROOF RACK/SKI
RACK 14) 7)
FASTENERS
The fasteners are located in the areas
shown in fig. 43.
To use the front fasteners, remove the
cap A fig. 43, accessible with the door
open.
The rear fixing areas B can be found
according to measurements shown in
fig. 44.
Lineaccessori Mopar
®at provides a
specific roof rack/ski rack for the
tailgate.
43DVDF0S178c

51
FUEL CUT-OFF
SYSTEM 8)
This intervenes in the case of an
impact causing:
❒ the fuel supply cut-off with the
engine consequently switching off
❒ automatically unlocking the doors
❒ switching on of all interior lights.
The intervention of the system is
indicated by a message shown on the
display.
IMPORTANT Carefully check the car
for fuel leaks, for instance in the engine
compartment, under the car or near
the tank area.
After a collision, turn the ignition key to
the STOP position to avoid draining the
battery.
To reset car operation, follow this
procedure:
❒ turn the ignition key to MAR
❒ activate the right direction indicator
❒ deactivate the right direction
indicator
❒ activate the left direction indicator
❒ deactivate the left direction indicator
❒ activate the right direction indicator
❒ deactivate the right direction
indicator
❒ activate the left direction indicator
❒ deactivate the left direction indicator
❒ ignition key turned to the OFF
position
❒ turn the ignition key to MAR.PARKING SENSORS
18) 25
(for versions/markets, where provided)
Located in the rear bumper fig. 51
these detect and inform the driver,
through an intermittent acoustic signal,
of the presence of obstacles at the rear
of the car.
As the distance from the obstacle
behind the car decreases, the acoustic
alarm becomes more frequent. The
buzzer becomes continuous when the
distance separating the vehicle from
the obstacle is less than about 30 cm.
It remains constant if the distance
between the vehicle and the obstacle
is unchanged.
If this situation concerns the side
sensors, the signal will stop after
approximately 3 seconds to avoid, for
example, indications in the event of
manoeuvres along a wall.
If several obstacles are detected by the
sensors, only the nearest one is
considered.

127
JUMP STARTING
26) 13)
If the battery is flat, the engine may be
started using an auxiliary battery with
the same capacity or a little higher than
the flat one.
IMPORTANT After turning the ignition
key to STOP and having closed the
driver’s side door, wait at least one
minute before disconnecting the
battery and then reconnecting the
electrical supply to the battery.
Proceed as follows:
Engage the handbrake on both
vehicles and place the gearbox
in neutral. Connect the positive
terminals (+mark near the terminal) of
the two batteries using a suitable lead.
With a second cable, connect
the negative terminal –of the auxiliary
battery to an earthing point E
on the
engine or the transmission of the car to
be started. Start the engine. When the
engine has been started, remove the
leads reversing the order above. If after
a few attempts the engine does not
start, do not persist but contact a Fiat
Dealership. IMPORTANT Do not directly connect
the negative terminals of the two
batteries: sparks could ignite explosive
gas released from the battery.
If the auxiliary battery is installed on
another car, prevent accidental contact
between metallic parts of the two cars.
For versions with Start&Stop
In the case of emergency starting,
NEVER connect the negative lead (–) of
the auxiliary battery to negative pole (–)
of the battery, but only to an earth
point on the engine/gearbox assembly.
IN AN EMERGENCY
98DVDF0S061c
In an emergency we recommend that you call the toll-free number found on the Warranty Booklet.
You can go to our web site at www.fiat500.com to find the Fiat Dealership nearest to you.