129
❒ If the vehicle is equipped with side
skirts, to let the jack pass under the
vehicle, the latter must be tilted (as
shown in 102)
❒ Make sure the jack is correctly
positioned (see fig. 103)
❒ Warn anybody who is nearby that
the car is about to be raised.
They should stay clear and they
should be warned not to touch the
car until it is back on the ground.
100DVDF0S063c
❒ For vehicles with wheel cap: use
the screwdriver provided, applying
leverage to the dedicated opening
on the outer edge.
❒ For cars fitted with alloy wheels:
remove the press-fitted hub cap
using the screwdriver provided.
❒ Loosen the fixing bolts for the
wheel to be changed by about one
turn using the spanner provided.
❒ Partially open the jack using the
handle.
❒ Arrange the jack close to the wheel
to be changed, next to the sign
fig. 100-101 indicated on the
bodywork.
102DVDF0S0163c
99DVDF0S062c
103DVDF0S065c
101DVDF0S064c
IN AN EMERGENCY
130
❒ Fit the handle to operate the jack
and raise the car until the wheel is a
few centimetres above the ground.
When turning the jack handle, make
sure that it can turn freely without
scraping your hand against the
ground. The moving components of
the jack (screws and joints) can also
cause injuries: avoid touching them.
If you come into contact with
lubricating grease, clean yourself
thoroughly.
❒ Loosen the bolts completely and
remove the wheel to be replaced.
❒ Make sure the contact surfaces
between space-saver wheel and
resting surfaces are clean so that
the fastening bolts will not come
loose.
❒ Fit the space-saver wheel aligning
the pin with one of the holes on the
wheel.
❒ Tighten the 4 fixing bolts, turn the
jack handle to lower the car and
remove the jack.
❒ Fasten the bolts completely,
passing alternately from one bolt to
the opposite one.REFITTING THE WHEEL
32) 40)
Versions with steel wheels
❒ Make sure the contact surfaces
between standard wheel and hub
are clean so that the fastening bolts
will not come loose.
❒ Fit the standard wheel inserting the
4 bolts into the holes, then tighten
them.
❒ Lower the car and remove the jack.
❒ Use the wrench provided to fully
tighten the bolts, passing alternately
from one bolt to the opposite one;
❒ Insert the pressure-fit cup making
the suitable slot coincide with the
inflation valve;
❒ Place the inner part of the hub cap
on the wheel rim;
❒ Engage the hub cap by applying an
axial force in several points as
shown in fig. 104 to allow the
correct coupling between hub cap
and wheel.
Versions with alloy wheels
❒ Place the wheel onto the hub and
tighten the bolts using the wrench
provided.
❒ Lower the car and remove the jack.
❒ Using the spanner provided, fully
tighten the bolts.
❒ Reinsert the press-fitted hub cap,
making sure that the reference hole
on the wheel is aligned with the
reference pin on the cap.
IMPORTANT: if it is not fitted correctly,
the hub cap may detach when the car
is running.
104DVDF0S461c
197(CONTINUES)
32) CHANGING A WHEEL
•The space-saver wheel (for versions/markets, where
provided) is specific to your car, do not use it on other models,
or use the space-saver wheel of other models on your car.
The space-saver wheel must only be used in an emergency.
Never use it for more than strictly necessary and never exceed
80 km/h.
•On the space-saver wheel there is an orange label,
summarising the main warnings regarding space-saver wheel
usage restrictions. Never remove or cover the label. The label
contains the following indications in four languages: “Warning!
For temporary use only! 80 km/h max! Replace with standard
wheel as soon as possible. Never cover this indication.” Never
apply a wheel cap on a space-saver wheel.
•If you change the type of wheel (alloy rims instead of
steel rims and vice versa) you will have to change the entire set
of fastening bolts with another set of suitably sized bolts.
•Alert other drivers that the car is stationary in compliance
with local regulations: hazard warning lights, warning triangle,
etc. Any passengers on board should leave the car, especially
if it is heavily laden. Passengers should stay away from on-
coming traffic while the wheel is being changed. On hills or
uneven roads, use chocks or appropriate objects to block the
wheels of the vehicle.
•The driving features of the car may change when a space-
saver wheel is fitted. Avoid violent acceleration and braking,
abrupt steering and fast cornering.
The total life of a space-saver wheel is approximately 3,000
km, after which it must be replaced by another wheel of the
same type. Never install a traditional tyre on a rim designed to
be used as a space-saver wheel.
PERSONAL SAFETY
(CONTINUED)
Have the wheel repaired and refitted as soon as possible. Using
two or more space-saver wheels at the same time is forbidden.
Do not apply grease to the bolt threads before fitting: they could
come unscrewed.
•Snow chains cannot be fitted to the space-saver wheel.
So, if a front (drive) wheel is punctured and chains are needed,
a rear wheel should be fitted to the front of the car and the
space-saver wheel should be fitted to the rear. In this way,
equipped with two normal drive wheels at the front, they can be
fitted with snow chains, thus resolving the emergency situation.
•If the hub cap is not fitted correctly, it may come off when the
car is travelling.
Never tamper with the inflation valve.
Never introduce tools of any kind between rim and tyre. Check
tyre and space-saver wheel pressures regularly, complying with
the values given in the “Technical specifications” chapter.
•The jack is a tool developed and designed only for changing a
wheel, if a tyre gets punctured or damaged, on the vehicle with
which it is supplied or on other vehicles of the same model.
Any other use, e.g. to jack up other vehicle models or different
things, is strictly prohibited. Never use it to carry out
maintenance or repairs under the vehicle or to change
summer/winter wheels and vice versa.
Never go under the raised vehicle. If any work under the vehicle
is necessary, contact the Fiat Service Network. Incorrect
placing of the jack can cause the vehicle to drop: use it only in
the positions indicated.
