2018 FIAT 500 change time

Dear Customer,
We would like to congratulate and thank you for choosing a Fiat.
We have written this handbook to help you get to know all the features of your vehicle and use it in the best possible way.
Here you will find information, advice and important warnings regarding use of your vehicle and how to achieve the best
performance from its technical features.
You are advised to read it right through before taking to the road for the first time, to become familiar with the controls and above all
with those concerning brakes, steering and gearbox; at the same time, you can understand the vehicle behaviour on different road
surfaces.
This document also provides a description of special features and tips, as well as essential information for the safe driving, care and
maintenance of your vehicle over time.
After reading it, you are advised to keep the handbook inside the vehicle, for an easy reference and for making sure it remains on
board the vehicle should it be sold.
In the attached Warranty Booklet you will also find a description of the Services that Fiat offers to its customers, the Warranty
Certificate and the detail of the terms and conditions for maintaining its validity.
We are sure that these will help you to get in touch with and appreciate your new vehicle and the service provided
by the people at Fiat.
Enjoy reading. Happy motoring!
This Owner Handbook describes all vehicle versions.
Options, equipment dedicated to specific markets or versions are not explicitly indicated in the text: as a
consequence, you should only consider the information which is related to the trim level, engine and version that you
have purchased. Any content introduced throughout the production of the model, outside the specific request of
options at the time of purchase, will be identified with the wording
(where provided).
All data contained in this publication are intended to help you use your vehicle in the best possible way. FCA Italy
S.p.A. aims at a constant improvement of the vehicles produced. For this reason it reserves the right to make changes
to the model described for technical and/or commercial reasons.
For further information, contact a Fiat Dealership.

13
INSUFFICIENT ENGINE OIL PRESSURE/DECAYED ENGINE OIL
When the ignition key is turned to MAR, the warning light (for versions/markets, where provided) switches on, but it should
switch off as soon as the engine is started.
NOTE For versions/markets, where provided, the indicator may be amber.
Low engine oil pressure
The warning light or the symbol switches on constantly along with a message on the display (for versions/markets, where
provided) when the system detects that engine oil pressure is low.
Engine oil degraded
The warning light switches on and a message is displayed (for versions/markets, where provided).
The warning light may flash in the following ways, depending on the version:
❑ cycles of 3 minutes with intervals with the warning light off for 5 seconds until the oil is changed.
After the initial warning, each time the engine is started up, the warning light will continue to flash in the same mode, until
the oil is changed. A specific message will appear on the display (for versions/
markets, where provided) in addition to the warning light. The lighting of this warning light should not be considered as a
fault, it simply informs the customer that the oil needs to be changed following normal car use.
Engine oil deterioration is accelerated by:
❑ mainly town use of the car which makes the DPF regeneration process more frequent;
❑ use of the vehicle for short drives, in which the engine does not have time to reach its regular operating temperature;
❑ repeated interruption of the regeneration process, signalled by the DPF warning light coming on.
vv
vv
DOORS/BONNET/LUGGAGE COMPARTMENT OPEN (versions with multifunction display)
The warning light appears on the display, together with a dedicated message, on some versions, when one or more doors,
the tailgate or the bonnet (for versions/markets, where provided) are not properly closed.
An acoustic signal is also emitted with the doors open and the car in motion.
ww
LOW BATTERY CHARGE
The warning light switches on when the ignition key is turned to MAR, but it should switch off as soon as the engine has
started (with the engine idling a brief delay before switching off is acceptable).
If the warning light or the symbol on the display (together with a dedicated message on the display on some versions)
remains on, contact a Fiat Dealership immediately.

35
With the selector switch in the AUTO
position, the side lights and dipped beam
headlights are controlled by the dusk
sensor.
MAIN BEAM
HEADLIGHTS
❒ With the ring in the 2position,
push the stalk forwards towards the
dashboard. The
1warning light on
the instrument panel will light.
❒ For vehicles with the AUTO
function: with the ring in the AUTO
position and the dipped beam
headlights on, push the stalk
forwards toward the dashboard.
❒ They are deactivated by pulling the
stalk towards the steering wheel.
Flashing
❒ You can flash the beams pulling the
stalk toward the steering wheel
(unstable position).
PARKING LIGHTS
These lights can be turned on with the
starter switch in the STOP position or
with the key removed, by moving the
left stalk ring first to the position (or
the AUTO position if the vehicle does
not have a dusk sensor) and then to
position
2.The warning light
3lights on the
instrument panel. Repeat the same
operation to switch them off.
DIRECTION INDICATORS
Bring the stalk to the (stable) position:
❒ up a: activates the right direction
indicator;
❒ down b: activates the left direction
indicator.
LANE CHANGE
FUNCTION
❒ Move the lever upwards or
downwards (unstable position) for
less than half a second and the
direction indicator will flash 3 times
to signal a lane change, then
immediately switch off
automatically.
FOLLOW ME HOME
This function allows the space
surrounding the car to be lit up for the
set period of time.
Activation
The “Follow Me Home” device is
activated by pulling the stalk fig. 25
towards the steering wheel, in addition
to the stroke end click.
EXTERNAL LIGHTS
DAYTIME RUNNING
LIGHTS
7)
❒ For vehicles with the AUTO
function: with the key in the MAR
position and the ring turned to the
O position, the daytime running
lights switch on automatically.
❒
For vehicles with the AUTO function:
the daytime running lights are turned
on automatically by the dusk sensor
when the ring is in the AUTO position.
DIPPED HEADLIGHTS/
SIDE LIGHTS
❒ With key at MAR, turn the ring nut to
2. The warning light
3on the
instrument panel will come on. When
the dipped beam headlights are on,
the daytime running lights switch off.
24
1
2
DVDF0S008c

KNOWING YOUR CAR
50
iTPMS System
(indirect Tyre
Pressure
Monitoring System)
(for versions/markets, where provided)
48)
RESET PROCEDURE
The iTPMS needs an initial “self-
learning” phase (with length depending
on the driving style and road
conditions: optimal conditions being
driving on a straight road at 80 km/h
for at least 20 minutes) which starts
when the Reset procedure is carried
out.
The Reset procedure must be carried
out:
❒ each time tyre pressure is
modified;
❒ when even only one tyre is
changed;
❒ when tyres are rotated/inverted;
❒ when the space-saver wheel is
fitted.
In a few situations such as sporty
driving, particular conditions of the
road surface (e.g. icy, snowy,
unsurfaced roads...) the signalling may
be delayed or partial in detecting the
contemporary deflation of more than
one tyre.
Under special conditions (e.g. vehicle
loaded asymmetrically on one side,
towing a trailer, damaged or worn tyre,
fitting the space-saver wheel, use of
the “Fix&Go” quick tyre repair kit,
fitting snow chains, fitting different
tyres on the axles) the system may
give false indications or be temporarily
deactivated.
If the system is temporarily
deactivated, the warning light
nflashes for about 75 seconds and then
is continuously on; at the same time,
the display shows a dedicated
message.
This indication is displayed also after
the engine has been switched off and
then on again if the correct operating
conditions are not restored. Before carrying out the “Reset”
procedure, inflate the tyres to the
rated pressure values specified in the
inflation pressure table (see “Wheels”
paragraph in the “Technical
specifications” chapter).
If the Reset procedure is not carried
out, in all above cases, the
nwarning light may give false indications
on one or more tyres.
To carry out the Reset procedure, with
the vehicle stopped and the ignition
key at MAR, use the setup menu (see
the description of the “Display”
paragraph). At the end of the Reset
procedure the display will show the
“Reset saved” message, indicating
that the self-learning has been started.
If the iTPMS self-learning is not
correctly executed, the message is not
displayed.
OPERATING
CONDITIONS
The system is active for speeds above
15 km/h.

KNOWING YOUR CAR
58
❒ switch A pressed rightwards
(identified by symbol Kindicates
petrol operation with lighting of the
respective amber LED C;
❒ switch A pressed on the left side
(identified by the symbol G)
indicates LPG operation with
activation of the associated green
LED D.
Five LEDs B (one amber and four
green) on the top part of the switch
display the amount of LPG in the
cylinders.
If the LPG runs out, the system
automatically switches to petrol: the
amber LED C besides the switch
comes on and the green LED D
indicating LPG operation goes off.
60DVDF0S0189c
After refuelling with LPG, after a normal
start-up on petrol, the fuel system
automatically returns to LPG: the
amber LED C next to the switch goes
off and the green LED D for LPG
operation turns on.
If you specifically wish to run on petrol,
press the switch A on the right-hand
side.
The amber LED C next to the switch
will turn on to indicate that switching
has taken place (the LPG fuel system
has been entirely disabled).
The fuel supply can only be returned to
LPG by operating switch A again,
green LED D next to the switch will turn
on to indicate that switching has taken
place.
In addition, when starting at outside
temperatures below approximately –
10°C, the switching times from petrol
to LPG increase to allow the pressure
regulator/reduction unit to heat up.
IMPORTANT If switching takes place
during acceleration or setting off, there
may be a brief drop in power.MULTIMEDIA
47)
10)
TIPS, CONTROLS AND
GENERAL
INFORMATION
Road safety
Learn how to use the various system
functions before setting off.
Read the instructions for the system
carefully before setting off.
Reception conditions
Reception conditions change constantly
while driving.
Reception may be interfered with by the
presence of mountains, buildings or
bridges, especially when you are far
away from the broadcaster.
IMPORTANT The volume may be
increased when receiving traffic
bulletins.

77
Connected services that can be
accessed on the vehicle
The Uconnect™ LIVE services
available in the radio menu can change
according to the market.
The eco:Drive™ and my:Car
applications were developed to
improve the customer’s driving
experience, therefore they are available
in all markets, where the Uconnect™
LIVE services can be accessed.
For further information visit the
www.DriveUconnect.eu website.
If the navigation system is installed in
the radio, accessing the Uconnect™
LIVE services enables use of the
TomTom LIVE services. Further
information about the LIVE functions is
available in the dedicated chapter.
eco:Drive™
The eco:Drive™ application allows you
to display your driving behaviour in real
time, in order to help you reach a more
efficient driving style as far as
consumption and emissions are
concerned.In addition, the data can be saved on a
USB flash drive, and the data analysis
can be made on your personal
computer thanks to the eco:Drive™
desktop application, available on
www.fiat.it or www.DriveUconnect.eu.
Driving style is evaluated by means of
four indices which monitor the
following parameters:
❒ Acceleration
❒ Deceleration
❒ Shifting
❒ Speed
eco:Drive™ display
Press the eco:Drive™ button to
interact with the function.
A screen will be displayed on the radio,
showing the 4 indices described
above. These indices are grey until the
system has enough data to evaluate
the driving style.
Once sufficient data are available, the
indices will have 5 colours depending
on the evaluation: dark green (very
good), light green, yellow, orange and
red (very bad).“Current trip index” refers to the entire
value calculated in real time based on
the average of the described indices.
It represents eco-friendliness of the
driving style: from 0 (low) to 100 (high).
In the event of extended inactivity the
display will show the average of the
indices up to that moment (”Average
index”) then the indices will be
coloured again in real time as soon as
the vehicle is restarted.
To check the data average of previous
trip (a “trip” is a cycle starting from
when the ignition key is turned on until
it is turned off), select the “Previous
Trip” button (fig. 4).
The details of the previous trip can also
be displayed by pressing the “Details”
button, in which duration (time and
mileage) and average speed will be
shown.

93
SIRI EYES FREE
(available with iPhone 4S and higher
and compatible iOS only)
After having paired the Siri enabled
device to Uconnect™ hold the
}button
on the steering wheel pressed and then
release it.
After the double beep, you can start
interacting with Siri, to listen to music,
make calls, read text messages and
more.
Uconnect™ LIVE
SERVICES
Press the Uconnect™ button to
access the Uconnect™ LIVEapps.
The services available depend on the
car configuration and the market.
To use the Uconnect™ LIVE
services, you need to download the
Uconnect™ LIVEapp from Google
Play or Apple Store and register using
the app or on www.DriveUconnect.eu.
First access to the vehicle
Once you have launched the
Uconnect™ LIVEapp and entered
your details, you have to pair the
Bluetooth® with your smartphone and
the radio, as described in the “Pairing
a mobile phone” chapter, to access
the Uconnect™ LIVEservices in your
vehicle.When pairing is complete, the
connected services can be accessed
by pressing the Uconnect™ LIVE
icon on the radio.
Before you can use the connected
services, you must first do the
Bluetooth®pairing, then complete
the activation procedure by following
the instructions that appear in the
Uconnect™ LIVEapp.
Setting of Uconnect™ LIVE
services that can be managed
through the radio
In the Uconnect™ LIVEradio menu
the “Settings” section can be accessed
by pressing the icon . In this
section the user can check the system
options and change them according to
their preferences.
System updates
If an update for the Uconnect™ LIVE
system is available while the
Uconnect™ LIVEservices are being
used, you will be informed with a
message on the radio screen.
Connected services that can be
accessed on the vehicle
The eco:Drive™ and my:Car
applications were developed to
improve the customer’s driving
experience, therefore they are available
in all markets, where the Uconnect™
LIVEservices can be accessed.
If the navigation system is installed in
the radio, accessing the Uconnect™
LIVE services enables use of the
“Live” services.
eco:Drive™
The eco:Drive™ application allows you
to display your driving behaviour in real
time, in order to help you reach a more
efficient driving style as far as
consumption and emissions are
concerned.
In addition, the data can be saved on a
USB flash drive, and the data analysis
can be made on your personal
computer thanks to the eco:Drive™
desktop application, available on
www.DriveUconnect.eu.
Driving style is evaluated by means of
four indices which monitor the
following parameters: acceleration,
deceleration, gearchange, speed.

95
To use Android Auto, the smartphone
must be connected to the car with a
USB cable.
On the first connection, you will have to
perform the setup procedure that
appears on the smartphone. You can
only perform this procedure with the
vehicle stationary.
Apple CarPlay – app configuration
Apple CarPlay is compatible with the
iPhone 5 or more recent models, with
the iOS 7.1 operating system or later
versions.
Before using Apple CarPlay, enable Siri
from Settings General Siri on the
smartphone.
To use Apple CarPlay, the smartphone
must be connected to the car with a
USB cable.
NOTE Enabling Apple CarPlay/Android
Auto or some functions could require
interaction on the smartphone. If
necessary, complete the step on your
device (smartphone).Interaction
After the setup procedure, the
application will run automatically on the
Uconnect™system when your
smartphone is connected to the USB
port in the car.
You can interact with Apple CarPlay
and Android Auto using the steering
wheel controls (long press of the
}button), using the SCROLL TUNE
button/knob to select and confirm or
using the Uconnect™system
touchscreen.
Navigation
With the Apple CarPlay and Android
Auto applications, the user can choose
to use the navigation system on their
smartphone.
If the system "Nav" mode is already on,
a warning pop-up will appear on the
Uconnect™system display when a
device is connected to the car with a
navigation session in progress.
The pop-up allows the user to choose
between using the system navigation
and using navigation controlled by the
smartphone.
The user can choose to change their
selection at any time by accessing the
navigation system that they want to
use and setting a new destination.Setting "AutoShow smartphone
display on connection"
Through the Uconnect™system
settings, the user can decide to view
the smartphone screen on the
Uconnect™system display as soon
as the smartphone is connected via the
USB port. When this function is set,
each time a connection is made via
USB, the Apple CarPlay or Android
Auto apps will run automatically on the
radio screen.
The "AutoShow smartphone display
on connection" item can be found in
the "Display" submenu. The function is
enabled by default.
NOTES
❒ Bluetooth®is disabled while Apple
CarPlay is being used
❒ Bluetooth®remains on while
Android Auto is being used
❒ The data connection will depend on
the tariff plan of the smarphone
This information may be subject to
changes that depend on the
smartphone's operating system.