2017 MITSUBISHI ASX Owner's Manual (in English)

Front fog lamps*
E01004003485
1. Remove the clip (A).
2. Insert a straight blade (or minus) screw-
driver with a cloth over its tip into the fog lamp cover (B) and pry gently to re-
move it.
3. Remove the screws (C) and remove the
lamp unit.NOTEl Except for vehicles equipped with daytime
running lamps, when unfastening the screws,be careful not to move the beam position ad-
justment screw (D).4. While holding down the tab (E), pull out
the socket (F).
5. Turn the bulb (G) anticlockwise to re-
move it.
6. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-33OGAE17E2Maintenance10

CAUTIONlHandle halogen lamp bulbs with care. The
gas inside a halogen lamp bulbs is highly
pressurized, so dropping, knocking, or scratching a halogen lamp bulb can cause it
to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the fog lamps are op- erated.
If the glass surface is dirty, it must be
cleaned with alcohol, paint thinner, etc., and refit it after drying it thoroughly.Daytime running lamps*
E01012400067
1. Remove the clip (A).
2. Insert a straight blade (or minus) screw-
driver with a cloth over its tip into the daytime running lamp cover (B) and pry
gently to remove it.
3. Remove the screws (C) and then remove
the lamp unit.
4. Turn the bulb (D) anticlockwise to re-
move it.
Replacement of lamp bulbs
10-34OGAE17E2Maintenance10

5.While holding down the tab (E), pull out
the socket (F).
6. To install the bulb, perform the removal
steps in reverse.
Rear fog lamp
E01004101596
1. When removing the lamp unit (A), push
it towards the left side of the vehicle body.
2. Remove the socket (B) and bulb assem-
bly by turning it anticlockwise.
3. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal
steps in reverse.
NOTEl If the wiring harness is pulled off the 2 har-
ness guides on the lamp unit while replacingthe bulb, make sure to secure the wiring har-
ness to the harness guides.
l When installing the lamp unit, first insert the
tab (C) into the groove (D) on the body, and then push on the lamp unit to fit it into place.
Replacement of lamp bulbs
10-35OGAE17E2Maintenance10

NOTERear combination lamps
E01004201366
1.Remove the screws (A) that hold the
lamp unit and remove the lamp unit.
2. Turn the socket and bulb assembly anti-
clockwise to remove it.
B- Stop and tail lamp (LED) - cannot be
replaced
C- Rear turn-signal lamp
NOTEl An LED, not a bulb, is used in the stop
lamp/tail lamp.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.
3. Pull the bulb out of the socket.
4. To install the bulb, perform the removal
steps in reverse.NOTEl When mounting the lamp unit, align the
groove (D) on the lamp unit with the clip onthe body and the pin (E) on the unit with the
hole in the body.Reversing lamps
E01004401430
1. Open the tailgate.
2. Insert a straight blade (or minus) screw-
driver into the notch of the cover and pry
gently to remove the cover.
Replacement of lamp bulbs
10-36OGAE17E2Maintenance10

NOTElWrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
cover.
3. Remove the socket and bulb assembly
by turning it anticlockwise.
4. Remove the bulb by pulling it out.
5. To install the bulb, perform the removal
steps in reverse.
NOTEl When installing the lid, align the tab on the
lid with the hole on the vehicle side.Licence plate lamps
E01004602093
1. When removing the lamp unit (A), push
it towards the left side of the vehicle body.
2. Remove the socket (B) and bulb assem-
bly by turning it anticlockwise.
Replacement of lamp bulbs
10-37OGAE17E2Maintenance10

3. Remove the bulb by pulling it out.
4.To install the bulb, perform the removal
steps in reverse.
NOTEl When installing the lamp, insert tab (C) first
then align and insert tab (D).High-mounted stop lamp
E01004500593
NOTEl An LED, not a bulb, is used in the high-
mounted stop lamp.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.
Replacement of lamp bulbs
10-38OGAE17E2Maintenance10

Vehicle labeling................................................................................ 11-02
Vehicle dimensions........................................................................... 11-04
Vehicle performance......................................................................... 11-06 Vehicle weight.................................................................................. 11-07
Engine specifications........................................................................ 11-10
Electrical system............................................................................... 11-11
Tyres and wheels...............................................................................11-12
Fuel consumption.............................................................................. 11-12
Refill capacities................................................................................. 11-15Specifications
OGAE17E211

Vehicle labelingE01100105207
Vehicle identification number
The vehicle identification number is stamped on the bulkhead as shown in the illustration.
Vehicle information code plate
The vehicle information code plate is riveted as shown in the illustration.
The plate shows model code, engine model,
transmission model and body colour code, etc.
Please use this number when ordering re-
placement parts.
1- Model code
2- Engine model code
3- Transmission model code
4- Body colour code
5- Interior code
6- Option code
7- Exterior code
Vehicle labeling
11-02OGAE17E2Specifications11