2017 MAZDA MODEL CX-3 Owners Manual (in English)

4–97
When Driving
i-ACTIVSENSE
How to Set the Speed
1. Adjust the vehicle speed to the desired
setting using the accelerator pedal.
2. Headway control begins when the
SET
or SET switch is pressed. The
set speed and the inter-vehicle distance
display ¿ lled with white lines are
displayed. The Mazda Radar Cruise
Control (MRCC) indicator light (green)
is indicated simultaneously.


Travel status Display
During travel at constant
speed


During travel under
headway control



N O T E
 


y If a vehicle ahead is detected while
traveling at a constant speed, the
vehicle-ahead indication is displayed
and headway control is performed.
Additionally, when a vehicle ahead is
no longer detected, the vehicle-ahead
indication turns off and the system
switches back to travel at constant
speed.
 


y Headway control is not possible if
the vehicle ahead is driving faster
than the set speed. Adjust the system
to the desired vehicle speed using the
accelerator pedal.

How to Set the Distance Between
Vehicles During Headway Control
The distance between vehicles is set to a
shorter distance each time the
switch is
pressed. The distance between vehicles is
set to a longer distance by pressing the

switch. The distance-between-vehicles can
be set to 4 levels; Long, medium, short,
and extremely short distance.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–98
When Driving
i-ACTIVSENSE
Distance-between-
vehicles guideline
(at 80 km/h (50 mph)
vehicle speed) Indication on display
Long (about 50 m (164 ft))

Medium (about 40 m
(131 ft))


Short (about 30 m (98 ft))

Extremely short (about
25 m (82 ft))



N O T E
 


y The distance between vehicles differs
depending on the vehicle speed, and the
slower the vehicle speed, the shorter the
distance.
 


y When the ignition is switched to ACC
or OFF and then the engine is started
again, the system automatically sets
the distance between vehicles to the
previous setting.

Changing the Set Vehicle Speed
Changing the set vehicle speed using the
SET switch
Press the SET
switch to accelerate.
Press the SET
switch to decelerate.
The set vehicle speed changes as follows
each time the SET switch is pressed.

Short press 1 km/h (1 mph)
Long press 10 km/h (5 mph)

N O T E
For example, the set vehicle speed is
changed by pressing the SET switch four
times as follows:
The vehicle speed accelerates or
decelerates by 4 km/h (4 mph).

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–99
When Driving
i-ACTIVSENSE
To accelerate using the accelerator
pedal
Depress the accelerator pedal and press
and release the SET
or SET switch at
the desired speed. If a switch cannot be
operated, the system returns to the set
speed when you release your foot from the
accelerator pedal.
CAUTION
The warnings and brake control do not
operate while the accelerator pedal is
depressed.

N O T E
 


y When accelerating using the SET
switch while in headway control, the set
vehicle speed can be adjusted but
acceleration is not possible. If there is
no longer a vehicle ahead, acceleration
continues until reaching the set vehicle
speed. Check the set vehicle speed by
viewing the set vehicle speed display in
the active driving display.
 


y When depressing the accelerator pedal,
the inter-vehicle distance display in the
active driving display changes to the
white-line display.
 


y The minimum settable speed is 30 km/h
(19 mph). If the set vehicle speed
reaches 30 km/h (19 mph) using the
switch operation, constant speed travel
is maintained at about 30 km/h (19
mph) even if the SET
switch is
pressed. The Mazda Radar Cruise
Control (MRCC) system is not canceled.

To Deactivate
The Mazda Radar Cruise Control (MRCC)
is canceled when the OFF switch is
pressed.
When the system is temporarily
canceled
In the following cases, the Mazda Radar
Cruise Control (MRCC) system is
temporarily canceled. The Mazda Radar
Cruise Control (MRCC) indicator light
(green) turns off simultaneously.
 


y The CANCEL switch is pressed.



y The brake pedal is depressed.



y The parking brake is applied.



y The selector lever is shifted to park (P),
neutral (N) or reverse (R).
 


y In the following cases, the beep sounds
one time.
 

y
 The vehicle speed decreases to less
than 25 km (16 mph).
 

y
 The DSC has operated.


y
 The TCS has operated for a certain
period of time.
 

y
 The Smart City Brake Support (SCBS)
has operated.
 

y
 The Smart Brake Support (SBS) has
operated.
 

y
 When traveling on a down slope for a
long period of time.
 

y
 There is a problem with the system.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–10 0
When Driving
i-ACTIVSENSE
N O T E
 


y The Mazda Radar Cruise Control
(MRCC) system may be canceled during
rain, fog, snow or other inclement
weather conditions, or the front surface
of the radiator grille is dirty.
 


y If you have temporarily canceled the
Mazda Radar Cruise Control (MRCC),
you can return to your previously set
speed by pressing the RES switch and
after all of the operation conditions
have been met.
 


y If the OFF switch is pressed to cancel
the Mazda Radar Cruise Control
(MRCC), the system does not return to
the previously set speed even if the RES
switch is pressed.

Cruise Control Function
While this function is operating, the
headway control operation is canceled and
only the cruise control function operates.
The vehicle speed can be set more than
about 25 km/h (16 mph).
Use the cruise control function on
expressways and other highways which do
not require a lot of repeated acceleration
and deceleration.
WARNING
Do not use the cruise control function in
the following locations:
Otherwise, it could lead to an accident.
 


¾ Roads with sharp curves and where
vehicle traffi c is heavy and there is
insuffi cient space between vehicles.
(Driving under these conditions
using the cruise control function is
not possible)
 


¾ Steep down slopes (Set speed may
be exceeded because suffi cient
engine braking cannot be applied)
 


¾ Slippery roads such as ice or snow-
bound roads (Tires could spin
causing you to lose vehicle control)

Always drive carefully:
The warnings and brake control
will not operate after the headway
control function is canceled and the
system is switched to only the cruise
control function. Depress the brake
pedal to decelerate according to the
surrounding conditions while keeping
a safer distance from the vehicle ahead
and always driving carefully.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–101
When Driving
i-ACTIVSENSE
Switching to cruise control function
When the ON switch is pressed
continuously for about 2 seconds while
the Mazda Radar Cruise Control (MRCC)
system is turned on, the system is switched
to the cruise control function.
The Mazda Radar Cruise Control (MRCC)
indicator light (green) in the instrument
cluster turns off and the cruise control
indication is displayed in the active
driving display.


WARNING
Always turn off the cruise control
function when it is not in use:
Leaving the cruise control function
turned on when it is not in use
is dangerous as it could operate
unexpectedly, resulting in an accident.

How to set the speed
Adjust the system to the desired vehicle
speed using the accelerator pedal.
Cruise control function begins when the
SET
or SET switch is pressed.
N O T E
 


y The system may not be able to maintain
the set speed constantly depending on
driving conditions such as steep up or
down slopes.
 


y The speed will continue increasing
while the SET
switch is pressed and
held. The speed will continue
decreasing while the SET
switch is
pressed and held.

How to increase the set speed
The set speed can be increased using the
following operations:
To increase speed using the SET

switch
Press and hold the SET
switch and
release the switch at the desired speed.
The set speed can be adjusted
incrementally (1 km/h (1 mph)
increments) by pressing the switch and
releasing it immediately. For example, if
the switch is pressed 4 times, the set speed
increases by about 4 km/h (4 mph).
To increase speed using accelerator
pedal
Depress the accelerator pedal and press the
SET
or SET switch at the desired
speed.
If the switch is not operated, the system
returns to the set speed after you release
your foot from the accelerator pedal.
How to Decrease the Set Speed
P r e s s t h e S E T
switch continuously and
release the switch at the desired speed.
The set speed can be adjusted
incrementally (1 km/h (1 mph) increments)
by pressing the switch and releasing it
immediately. For example, if the switch
is pressed 4 times, the set vehicle speed
decreases by about 4 km/h (4 mph).
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–102
When Driving
i-ACTIVSENSE
Cancelling the function
Cancelling using OFF switch
When the OFF switch is pressed, the
cruise control function is cancelled.
Cancelling using ON switch
When the ON switch is pressed
continuously for about 2 seconds, the
cruise control function is canceled and
the headway control function is made
available for operation.
The cruise control function is canceled
automatically in the following cases. If
the RESUME switch is pressed while
the vehicle speed is 25 km/h (16 mph) or
higher, the speed returns to the original set
speed.
 


y The CANCEL switch is pressed.



y The brake pedal is depressed.



y The parking brake is applied. 



y The selector lever is shifted to P or N
position.

N O T E
 


y If the vehicle speed decreases by about
15 km/h (9.4 mph) or more than the set
speed, the cruise control function may
be canceled.
 


y When the vehicle speed is less than
21 km/h (13 mph), the cruise control
function is canceled. In this case, the
vehicle speed will not return to the
original set speed even if the vehicle
is accelerated to 25 km/h (16 mph) or
higher and the RES switch is pressed.
Reset the cruise control function.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–103
When Driving
i-ACTIVSENSE
*Some models.
Smart City Brake Support (SCBS) *
The Smart City Brake Support (SCBS) system is designed to reduce damage in the event
of a collision by operating the brake control (SCBS brake) when the system's laser sensor
(front) detects a vehicle ahead and determines that a collision with a vehicle ahead is
unavoidable. It may also be possible to avoid a collision if the relative speed between your
vehicle and a vehicle ahead is less than about 20 km/h (12 mph).
In addition, when the driver depresses the brake pedal while the system is in the operation
range at about 4 to 30 km/h (2 to 18 mph), the brakes are applied ¿ rmly and quickly to
assist. (Brake Assist (SCBS brake assist))


Laser sensor (front)

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–104
When Driving
i-ACTIVSENSE
WARNING
Do not rely on the Smart City Brake Support System (SCBS) as a substitute for safer
driving:
The Smart City Brake Support (SCBS) system cannot compensate for unsafe and reckless
driving, excessive speed, tailgating (following another vehicle too closely), and driving on
slippery roads such as wet, snowy, and icy roads (reduced tire friction and road contact
because of water on the road surface). You can still have an accident.

Do not rely completely on the Smart City Brake Support (SCBS) system:
 


¾ The Smart City Brake Support (SCBS) system is only designed to reduce damage in the
event of a collision. Over reliance on the system leading to the accelerator pedal or
brake pedal being mistakenly operated could result in an accident.
 


¾ The Smart City Brake Support (SCBS) is a system which operates in response to a
vehicle ahead. The system may not be able to detect or react to two-wheeled vehicles
or pedestrians.
 


¾ The laser sensor (front) for the Smart City Brake Support (SCBS) system is installed near
the rearview mirror. To assure the correct operation of the Smart City Brake Support
(SCBS), heed the following cautions.
 

¾
 Do not apply stickers to the surface of the windshield near the laser sensor (front)
(including transparent stickers). Otherwise, the laser sensor (front) may not be able
to detect vehicles ahead which could result in an accident.
 

¾
 Do not apply coating agent to the windshield. Otherwise, the laser sensor (front)
may not be able to detect vehicles or obstructions in front which could result in an
accident.
 

¾
 Do not disassemble the laser sensor (front).


¾
 If cracks or damage caused by fl ying gravel or debris is visible near the laser sensor
(front), stop using the Smart City Brake Support (SCBS) system immediately and
have your vehicle inspected by an Authorized Mazda Dealer. If the vehicle continues
to be driven with cracks or scratch marks left on the windshield near the laser sensor
(front), the system may operate unnecessarily and cause an unexpected accident.
  Refer to Stopping The Smart City Brake Support (SCBS) System Operation on page
4-107 .
 

¾
 When replacing the windshield wipers or windshield, consult an Authorized Mazda
Dealer.


Do not modify the suspension:
If the vehicle height or inclination is changed, the system will not be able to correctly
detect vehicles ahead. This will result in the Smart City Brake Support (SCBS) system not
operating normally or mistakenly operating, which could cause a serious accident.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD